hi there,
i bought this phone off ebay from someone who said i can reflash it to work.
it appears that the phone is realy dead.
The phone starts at&t splash appears, seems that it boots ok, however another splash screen appears saying GOODBYE and the phone powers off itself.
i tried to connect the phone on my PC with no luck. Used all the drivers and instructions through various forums but it appears that the phone is only found as "unknown device"!
When I try the Bootloader mode, I get :
*USB Downloader-Xcingular V1.2
[Phone] Active OFF
If i press left soft key + camera + power button, it boots into some other menu that has the windows moobile logo and on the very top it says:
Hit space or "0" to enter configuration
then if i press other buttons on the mouse it lists the following and after a few seconds it boots and powers off as in normal mode.
OEMLaunch BOOT Version : i607UCGD
INFO: Launch Windows CE .NET by jum
is there a solution to this stupid flash or shall i keep the accessories and battery and throw it in the garbage.
cheers
tio
Unfortunately no one has yet discovered a way to recover from this (flashing the wrong eboot to the phone)
If you are going to discard it, I would be willing to pay shipping etc. to see if I could resurrect it.
how would you go about doing that man?
i could resurrect it too if it was possible.
would a serial cable do the job?
is it the bootloader the problem?
is it that the phone cannot be recognized by the PC?
what is the problem here actually?
Related
Hi, so I found my old HTC Tattoo, and tried to boot it.
If I just try to boot it normally, it just stops at the TATTOO screen.
If I try to boot it while plugged into the computer, it does the same thing, but it also says FASTBOOT USB in the upper left corner, and my computer won't recognize it, it just says that there is something wrong with the usb device.
If I try to press MENU + BACK, and tap POWER, the menu comes up, flashing, and appears to be frozen, it does that until I release MENU + BACK, then it just starts to show the TATTOO screen, same with, or without computer.
So, can anyone help? I am a noob, so please give me easy directions
I'll be very happy for any help
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
vadeld said:
Hello guys, I'm new here and I hope you can help me out.
Let me make the story short.
My phone's screen broke and I replaced.
In that processes I lost the rubber that stick
to the panel of the volume. I was fine with that since my phone
in vibrate mode and I really don't use ring tone in my daily basis.
I tried to download Android 5.0 lollipop and flash it.
How did I get there? well since I did not have a volume button,
I downloaded an app that restarted my phone and got me into
fastboot mode without the key (I did got me where I wanted).
Then the problem was that in the middle of writing the .img
the freaking cheap bastard micro usb unplugged!!!
BAMM!! phone now is bricked, I cannot get into recovery/fastboot mode
since I cannot press the volume key and my phone is bricked.
I tried going through fastboot mode via my computer again,
but the computer doesn't recognize the device since it still
looping there forever at the google logo. I try installing USB
DRIVERS to see if I could do some "magic" haha. Got
error "This device cannot start ..." And still at the same problem.
I know I can get back to my recovery if order the part for the volume
key, I ordered the part to replace it, but trust me I was 3 weeks without
my phone and now this problem
Is there any way that I can get to fastboot mode to factory reset my phone
without volume key with a bricked forever looping a "google" logo ? :fingers-crossed: :fingers-crossed:
I appreciate any help.
Click to expand...
Click to collapse
Im not sure why your text is like this? But paraphrasing buddy comes a long way
Just hold the power button, until it dies, or just let it die in general since your volume button (You only need Vol down and Power) to power it off completely. Since your Volume keys are gone, the best solution is to wait for the replacement before doing so, unless you can get the contact keys to trigger the Volume button, you're in a loss atm. No OS or Volume keys means you can't trigger ADB commands or boot into fastboot. Just wait it out I guess?
Hello,
I tried installing Android Lollipop (Unofficial nightly build of CyanogenMod 12.0) on my LG G2 D802 model and now my phone is totally stuck in the boot. At first it shows the LG logo and then it show the LG logo and the text "Security Error" underneath. I think I've tried all combinations of "button-holding" during startup but I'm not able to access the recovery mode (or any other mode). I've tried hooking it up with the computer (Windows 8.1) but it doesn't seem to see it.
I'm pretty embarrassed by the whole situation :silly: so any help/guidance would be greatly appreciated! Thanks in advance.
Edit:
I've made some progress, but still not enough to get me through this. For some strange reasons the hardware shortcuts seem to be different for me than what is normally advertised on this forum (and the Internet).
I'm able to get into "Hardware Key Control Mode" using Vol-Down + Power + Vol-Up... not that is really useful.
I'm also able to get into "Factory data reset" i press Vol-Down + Power, then once the LG logo shows: Vol-Down + Vol-Up.
(Other places say I should press Vol-Down + Power, then Vol-Up + Power).
However that doesn't really fix anything. It momentarily shows the green Droid being operated on (1-2 seconds) but then shuts down. Then still the "Security Error"
So now I'm wondering if there is any other key-combination to get me into download/recovery mode?
Try just holding volume up when device reboots. And make sure your attached to a usb, this should get you to download mode. To reboot hold power button until reboot.
blas4me said:
Try just holding volume up when device reboots. And make sure your attached to a usb, this should get you to download mode. To reboot hold power button until reboot.
Click to expand...
Click to collapse
Thanks for the reply but that doesn't work either.
I tried the following:
Holding the Volume down button (while phone is off) and plugging in the USB
Holding the Volume Up button (while phone is off) and plugging in the USB
Holding the Volume down + Volume Up button (while phone is off) and plugging in the USB
I've tried two USB ports on my computer, USB2 and USB3. All of the above leave me at the same "Security Error" screen.
I've also tried:
Powering it on while holding VolDown + Power, when LG logo comes up - release it and immediately do the same thing again and hold them down => the phone just turns off
Press and hold the Volume Down button and the Power button, when the LG logo is displayed release the Power button only then immediately press and hold the Power button again => does nothing.
Press and hold the Volume Down button and the Power button, when the LG logo is displayed release both buttons and then immediately press and hold the both buttons again => does nothing.
Tried the same as above, but with Volume Up
Hoping for more suggestions!
As this is the internation version of the phone (D802) I was wondering if there might be a different combination of buttons to access the download mode or the recovery mode... anyone have a clue?
I really don't want to throw away my phone
If you have removed your laf partition to allow access to fastboot you won't be able to access download mode. Another is that you say your key combos seem to be different... Where did you purchase the phone? From eBay/Craigslist style websites or from your carrier? It's possible that you don't actually have the model you believe you have.
ShadowEO said:
If you have removed your laf partition to allow access to fastboot you won't be able to access download mode. Another is that you say your key combos seem to be different... Where did you purchase the phone? From eBay/Craigslist style websites or from your carrier? It's possible that you don't actually have the model you believe you have.
Click to expand...
Click to collapse
I did all sorts of stuff when I tried to install this (very hackish and little research) but I don't remember removing the laf partition (not that I know what that is - but I do remember messing with partitions because the phone doesn't have an external SD card). If I can't access download mode, is there anything else that I can do? Is it possible it is ruined? Really?
The phone was bought new from a respectable company here in Iceland and the sticker on the box says it's LG-D802. It has an IMEI number and a S/N (any way for me to verify based on that?)
There's a nice thread on here somewhere regarding unbricking a phone that's lost download mode. I'd link you it but I'm not near my PC ATM. You can verify model on the LG support page I believe. As for the unbricking, be prepared with an Ubuntu live CD to follow the instructions.
Edit: I noticed you said you were messing with the partitions, what exactly did you do with them? It may be of help.
ShadowEO said:
There's a nice thread on here somewhere regarding unbricking a phone that's lost download mode. I'd link you it but I'm not near my PC ATM. You can verify model on the LG support page I believe. As for the unbricking, be prepared with an Ubuntu live CD to follow the instructions.
Edit: I noticed you said you were messing with the partitions, what exactly did you do with them? It may be of help.
Click to expand...
Click to collapse
I'm guessing you are referring to this thread: http://forum.xda-developers.com/showthread.php?t=2582142
I hade downloaded Ubuntu and ran it in VMWare but it didn't seem to see any traces of my phone. I ran "ls /dev/sd*" but didn't find the phone there. Windows doesn't see anything either (e.g. device manager, nothing happens when I plug in the USB). Wonder if it would help if I ran Ubuntu directly from a USB stick? (The thread did say it was OK to run within a virtual machine)
Any further pointers appreciated!
Make sure that your phone has been passed through to VMware via the USB status icon in the lower right corner. It may indeed be easier to run it from a USB stick as you won't need to mess with the USB Virtualization layer in VMware as much. And I do believe that is the thread I was meaning.
ShadowEO said:
Make sure that your phone has been passed through to VMware via the USB status icon in the lower right corner. It may indeed be easier to run it from a USB stick as you won't need to mess with the USB Virtualization layer in VMware as much. And I do believe that is the thread I was meaning.
Click to expand...
Click to collapse
Hi, this is me again... now posting from Ubuntu (from a USB stick). I tried the instructions given in the mentioned thread but my phone does not seem to show up at all:
Code:
[email protected]:~# ls /dev/sd*
/dev/sda /dev/sdb /dev/sdc /dev/sdc2 /dev/sde /dev/sdg /dev/sdh1
/dev/sda1 /dev/sdb1 /dev/sdc1 /dev/sdd /dev/sdf /dev/sdh
Once I plug in the phone and execute the same command, it gives me the same results. I've executed it multiple times during the phone startup but it didn't show up for one second. I even tried executing it during the "Reset Data to factory" process... no difference. I verified the USB port was working OK by sticking (another) USB key into it and running the command and that drive showed up just fine (using ls /dev/sd*).
Love to hear more - and thanks again for helping out! :good:
Plug it into a windows machine if available and let us know how it's showing up (if at all) in device manager. Look especially for any device mentioning "qualcomm".
iowabowtech said:
Plug it into a windows machine if available and let us know how it's showing up (if at all) in device manager. Look especially for any device mentioning "qualcomm".
Click to expand...
Click to collapse
Hi,
I see no traces of it in Windows / Device Manager (see screenshot)
It may be a hard brick, in which case you may need to get a replacement. Sadly if you're not seeing Qualcomm devices anywhere in any of the categories in device manager, then the phone isn't entering qcom bulk mode which is bad :/ I guess that if you're worried about warranty you could possibly use the update gone bad excuse to get an RMA but I'm not sure if that will fly.
I have international D802 where I have installed a custom rom based on android 4.4.2. Yesterday I wanted to upgrade it to an android 5 rom and and mistakenly installed a new custom rom that was builded for F320S. After reboot only the fastboot mode was displayed. Then I’ve tried to repair the download mode by flash the img files, but as I’ve verified later they was not intended for LG G2 D802 32Gb version. So now if I try to enter either the download mode or the hard reset / recovery I see only the LG logo with security error.
I’ve tried a different button-combinations. Please correct me if it was wrong.
For power off I’ve pressed the power button for about 15 seconds, wait until the logo is displayed then hidden then shortly displayed again and then the display is black.
For hard reset / recovery I’ve pressed press volume down button and power button together until the LG logo appears on the screen. When the LG logo is displayed, un-pressed the power button, but keep pressing the volume down key and then pressed once more the power button. Then the LG logo is displayed again, and then below was the security error displayed.
For download mode, I’ve pressed and hold the volume up button and connected the USB cable. But after some seconds the security error was displayed and the device manager in windows didn’t showed any changes.
Is it possible to recover the phone from the security error state? Any help would be appreciated.
EDIT:
Solved in following steps.
1. Open the phone like described here: LG G2 is UNBRICKABLE NOW!
It was not hard and you don't need any special tools, only a small screw driver. Look first this both videos https://www.youtube.com/watch?v=15krGmydqgQ&feature=youtu.be and http://forum.xda-developers.com/show....php?t=2582142. The do the steps till you can access the processor chip. Ensure the battery is disconnected. By disconnecting the both left and right plates be sure to separate it from the surface.
2. Connect the phone to the PC with USB cable. Open the device manager.
3. Short the test pins on the chips, see the https://www.youtube.com/watch?v=FiofVOqfnxw with e.g. bent paper clip till you'll see the new QHSUSB qualcomm 9006 connection on COM port. Then you'll see a lot of windows messages about to format the new founded partitions. Close them.
4. Flash an images, like laf.img,aboot.img, boot.img from your phone model using export very partition see https://www.youtube.com/watch?v=_d5b_osUTug for details and files.
5. Now the download mode is available. Remove the usb cable, enter the download mode and flash a original stock rom for your model using the LG Flash Tool 2014.
Now your phone is unbricked!
Any questions?
What is the security error on LG G2? Is it a common way to reset some settings to reset it?
Added solution in the first post. If you have any questions, please post.
Ive done till step 3, only one window poped up, and i don't get step 4, i still got the security thing...
Help I guess?
avi57 said:
Ive done till step 3, only one window poped up, and i don't get step 4, i still got the security thing...
Help I guess?
Click to expand...
Click to collapse
You've shorted a wrong pin, please try again step 3 untill you will see the qualcomm 9006 and not 9008 or another number.
Hello dear forum users. Help me to repair Samsung gt-i9500 phone. The phone turns on but it does not boot beyond the logo. It is impossible to turn off the phone either. I have to remove the battery to turn it off. I wanted to do a hard reset, but it didn't work either. I went into factory mode, but the on / off button just does not work there to select menu items. There are 6 items in factory mode menu: 1)Full test 2) Item test 3)Test report 4)clear eMMC 5)version 6)reboot. I read on the Internet that clear eMMC is a hard reset, but I can’t choose. The phone does not respond to pressing the on/off button to select. The phone does not respond when trying to select other items too. I have googled that i need to flash the phone in this case. I connected the phone to the computer using a usb cable. Installed the driver.I entered factory mode on the phone.Phone is successfully recognised by Windows. I downloaded sb flash tool and downloaded one of GT-i95** MT6575 roms also.I have launched sp flash tool and choosed scatter file from rom folder that i have downloaded and pressed download button. But process didnot started and nothing happened. Sp flash tool didnot started process.I have attached screenshot of device info from Skipsoft Android Toolkit. I dont know why it have strange serial number . Maybe someone tried to repair it but unsuccessfully or i dont know.I can run adb on this device and can view files on this device with adb. I dont know how to get root on this device with only adb option to interact with device.I cannot get to download mode also . It shows me red triangle with exclamation mark. In this screen i pressed on/off button + vol.up button to enter . No response to this from device.Also Windows didnot recognise device when i pressed vol.down + home+on/off .It shows unrecognised device in device manager.But in Factory Mode this device was recognised by Windows.So i stucked in repairing this device. So guys what to do next to repair this device ? thanks for answers.