Related
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
fulgerul said:
hello everyone. i just bought a g3 wich remains stuck in the ipl/spl screen. i tried VIPPIE 's tutorial (many thanks man for ur work) and flash button rom 1.05 to revive the phone. it flashed without any error , but same result. phone doesnt pass the ipl/spl screen. next i tried to flash Xda_MiniS_LaunchROM_v154102, flashed ok but nothing happend. i m just stuck on the ipl/spl screen. the phone isnt bricked but i can not start it to do a soft spl and flash it. any ideas ?
because it s an o2 xda mini s , i thought an original o2 rom would do the trick (start the phone) but i couldnt find an original rom (tried the xda dev ftp page and the o2 one).
many thanks
ps:sorry for the double posting(wizard+wm6) but now i figured out that since my phone doesnt start and hasnt a wm6 rom on it , the place for this thread is here
Click to expand...
Click to collapse
Is it the Bootloaders screen(Tricolor) with IPL/SPL or initial loading screen with ipl/spl ?
What ipl/spl...? it displays at the moment ?
You can try to get into Bootloaders mode (tricolor screen) by pressing and holding down the camera button and press the Soft Reset button at the same time with the stylus or turn off the phone and while pressing and keeping holding down the camera button,Power On the phone,it'll wake up and go into Bootloaders (tricolor screen).if it goes into bootloaders,connect your phone to the pc via usb and check if small usb appears at the bottom of the bootloaders screen,if its there run the Ruu to flash,But first post your present ipl/spl..? here.
Cheers
hmm , this is from XDADeveloperWiki
Once the flash is done and your Wizard is rebooted, it will display an IPL of 1.xx and an SPL of 2.xx.
Click to expand...
Click to collapse
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
zabardast_1 - many thanks for the quick reply mate. it starts with the ipl spl screen. i wrote the values above.
i get it into bootloader with the camera + on button , bot the active sync on the systray , doesnt activate, it remains grey (like no device is connected). weird stuff.
yesterday i just upgraded a g4 wizard to wm6 and everything went smooth , an now
fulgerul said:
hmm , this is from XDADeveloperWiki
well, in my case , after button rom flashes wizard displays IPL 1.01 SPL 1.03 and after i flash the xda_mini_launch_rom it displays IPL 1.03 SPL 1.05 . NOT SPL 2.xx as mentioned in the tutorial . why ?
Click to expand...
Click to collapse
ok,after flashing button's rom or xda_mini you'll certainly have an ipl/spl 1.xx,cuz these roms have actually ipl/spl 1.xx,they are aku 1.xx roms,it's required to have ipl/spl 1.xx to use lokiwiz02b tool to SIM/CID unlock the phone,only then it can be upgraded to any wm6 roms.But to upgrade to wm6 its essential to have ipl/spl 2.xx,so to get to ipl/spl 2.xx,you have to flash your phone with T-mobile 2.26,then it'll show an ipl/spl 2.xx as required,ok
Cheers
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Activesync will not work in bootloaders mode,bootloaders cut off the activesync,you can only verify the connectivity between your phone and pc,if in bootloaders,connect the phone to the pc via usb cable and check if small usb appears at the bottom of the bootloaders,if its there then just flash the rom,there's no need to establish connection through activesync,ok
fulgerul said:
thanks mate , but in order to do the lokiwiz soft spl i need to have a working phone (i need to write the cab into my phone and execute). by doing so , my phone needs to work after flashing the button rom or the xda mini launch rom (right?). but mine , after flashing, remains in the ipl/spl screen (not the bootloader).
if i flash an o2 xda mini original rom , do i have a chance to revive the phone and to start it in order to apply the lokiwiz soft spl ?
Click to expand...
Click to collapse
YES ! first of all you got to have a working OS on the phone to activesync,only the you can perform with lokiwiz02b,ok
ok , so what should i do in order to start it succesfully and use lokiwiz. i cant find an original o2 rom and button rom or launch rom doesnt start my phone. what can i do ?
the o2 roms were deleted from xda dev ftp
ps : mate , if u r kind , log in to yahoo or msn , i m trying to contact u . ty
after a lot of searching and digging, i found the missing xda dev ftp O2 original roms . i flashed Xda_MiniS_LaunchROM_v154102 , everything went ok , same result. doesnt pass the ipl spl screen. tried RUU_Wizard_1050402_101_11210_O2_ENG and same thing. im getting really confused. my pc responses when i connect the wizard, it flashes with no errors , but it wont start. what can i try more ?
ohh, i have made a new nasty descovery: when i keep pressed down the comm button and the voice button and press the reset with stylus, the phone turns off and restarts in spl/ipl screen instead of hard resseting. is it really messed up ?
I'm afraid m8,it has most probably some hardware issues,better get it checked by some techy or mobile repair shop.
Cheers !
thanks mate. you are most probably right. do you have any idea what should be checked and how ? i ask this because the software part is clearly damaged.
can i revive it using mtty program ? as a last resort. some mtty commands ? ty
dear friends,
i have just bought the htc p4350 and noticed that when i boot the the device it does not display anything i.e the ipl, spl , gsm etc
my question how should i flash the device with the cooked roms available here without bricking the device
thanking all in advance
thanks and regards
faizell
Are you looking for this info when you turn the device on (looking at the splash screens) or when you put the device in bootloader (tri-color) mode? As far as I know, the splash screens won't show any info, but if you put the device in bootloader mode (hold down camera button and soft-reset with reset hole) the IPL and SPL should show up. Not sure where else on the phone to get this information other than running the RUU.
And it's definitely a good idea to check those numbers out before HardSPLing.
faizeliza said:
dear friends,
i have just bought the htc p4350 and noticed that when i boot the the device it does not display anything i.e the ipl, spl , gsm etc
my question how should i flash the device with the cooked roms available here without bricking the device
thanking all in advance
thanks and regards
faizell
Click to expand...
Click to collapse
lennyjaxn
thanks so much i have the ipl and spl which shows 4.24
now i will get back to reading how to flash it
i had the imate kjam and whenever you soft reset the phone it would dispaly the ipl,spl etc on the splash screen hence i presumed that this also should apply for the 4350
thanks once again
regards
faizell
No problem! Glad I could give something back after the tons of help I've gotten from this place!
I can understand your confusion, for sure. I had another phone that showed that info on the splash screen as well.
Hi everybody,
I went to a store this evening in order to unlock my Polaris. The owner of the store has got a HTC herald with a problem that he wanted me to solve.
He tried to install another rom on his herald but, due to an unsuccessfull rom upgrading, the HTC is locked on a RGB screen (red green blue) with the only following indications:
RUU
IPL 1.08.0001
SPL 1.08.0001
USB (or nothing when not plugged)
Would you mind helping me? I tried several Roms, and there was only one that seemed to work (ROM HERALD_ smiley sWWE.gif _6.1.405.13_BUILD 20764.1.4.3): It gave me a progress bar on the HTC frozen at 0% while the upgrading tool on the pc told me that I needed a more recent upgrading tool.
What can I do?
Thanks for all the solutions you'll give me
Nounou7701
(sorry for my bad english, I'm only a 15 years old french guy, wich explains that way of speaking english)
Before installing cooked ROMs I believe the phone must be HardSPL'ed, and this can only be done if the SPL/IPL is 4 or above - any lower/not HardSPL'ed and the device will be bricked. The screen you are describing is the bootloader, and since you only have an IPL/SPL of 1.x I'm pretty sure you can't install custom ROMs. To unbrick the device, turn it onto the bootloader and then load the original HTC ROM that came with the device.
Hope this helps,
czhang
Dear Czhang,
I tried several times to enter in bootloader, but it's impossible as it starts with the bootloader menu! I can't change anything about that, even by soft resets, reset+camera, reset+buttons...
Do ya think this could work properly? http://forum.xda-developers.com/showthread.php?t=417930
As I am stucked with 1.08.0001 SPL, There is nothing to do. All the users who tried to unbrick their phone didn't got it working, except one who changed the motherboard for... 200$ ! The price of a used HTC Herald in very good conditions!
Still looking for help
Thanks
Nounou7701
sorry to say sir but your ipl and spl should have been 4.0 or higher and also HardSPL'ed. i'm pretty sure your device is bricked. GL on finding a way to fix it or buying a new one. =D
Nounou7701, though you cannot flash a cooked ROM with IPL/SPL 1.x you can definitely flash the official ROM from HTC.
AAAARRRGGHHH! thanks to everyone for the (bad ) news... I'll try to buy a mothercard, just like another user did...
Have a nice evening
Nounou7701
nounou7701 said:
Hi everybody,
I went to a store this evening in order to unlock my Polaris. The owner of the store has got a HTC herald with a problem that he wanted me to solve.
He tried to install another rom on his herald but, due to an unsuccessfull rom upgrading, the HTC is locked on a RGB screen (red green blue) with the only following indications:
RUU
IPL 1.08.0001
SPL 1.08.0001
USB (or nothing when not plugged)
Would you mind helping me? I tried several Roms, and there was only one that seemed to work (ROM HERALD_ smiley sWWE.gif _6.1.405.13_BUILD 20764.1.4.3): It gave me a progress bar on the HTC frozen at 0% while the upgrading tool on the pc told me that I needed a more recent upgrading tool.
What can I do?
Thanks for all the solutions you'll give me
Nounou7701
(sorry for my bad english, I'm only a 15 years old french guy, wich explains that way of speaking english)
Click to expand...
Click to collapse
He didn't head the warning of the SPL requirements. You can easily revive it using the GoldCard method. (Search for the term "goldcard herald".)
HTC P4350 do not switch on after a bad SPL
I've tried to flash my Hera 100 P4350 with HardSPL Herald, but I got an error message it has switched off and I can't get my mobile switched on again.
It looks like completly dead (kaput).
Can anyone help me ? Or explain why that happened ?
TIA,
dark_side61
HTC P4350 do not switch on after a bad SPL
After a total reset (left soft touch + right soft touch + reset) I got the
IPL 1.08.0001
SPL 1.08.0001 screen but with no USB on the lower left corner of the screen
After arrived here what shoul I do to reinstall my P4350 ?
What do I need to have ?
TIA
dark_side
Do what Ivan said!
Search for Goldcard to fix it....
Dears Freinds
I have Qtek s200 and i Upgrade it from win 5 to win6.5 and when it restart hang up and dosent work any more
so pls can anyone help me
Muamer
By Hung up do you mean it goes into the bootloader screen (tri-colour)
First things first
Did you perform a HardSPl if not you need to do this first. Do a search for it, but make sure you get the correct one. By this I mean a G3 or G4, when you go into the bootloader screen look at the SPL if it ends in .000 it is a G3 if it ends in .0001 it's a G4.
This is just the same as flashing a Rom.
Then check this page and download the Qtek NVID Rom flash that and it should get your beloved prophet back to WM5
http://wiki.xda-developers.com/index.php?pagename=Prophet_ROMs
BUT before you do any flashing open up your activesync click on FILE then CONNECTION SETTINGS uncheck ALLOW USB CONNECTIONS then OK.
Then connect your phone via the USB in bootloader mode (press and hold the communication button and press the reset button keep holding the communication button until you get the tri colour screen) look at the bottom left of the screen for USB (in the white part) as long as you have got this you can begin flashing.
Dear Dixiesmu
when I turn in on i jus t get the first page
IPL 2.10
Spl 2.20.0000
gsm 02.47.21
os 10.1.0.811
And i wnat to tel u that befor the os is windows 5 with sweden lang.
so the link u gave me dosent include sweden so can i use the english rom
and im new in this feld so can help me more if u can and i will appreciate that
Many thanx for you reply
My freind
I did what u suggest and it works and now my qtek is working agian and can i upgrade it to win6.5 and if u have tje link for my qtek pls send it me
Thanx again for your help
Muamer
WM6.0/6.1/6.5 Roms
I have found that Bikertibi roms seem to be the best (only my opinion and no disrespect to the other fantasic chefs, long may thier excellent work continue ).
They also include the HardSPL for both G3 and G4 devices.
Another good one is Gullum's Prophet TouchXB if I recall this also includes the HardSPL, but please check as I am not 100% certain.
G4
Hi Malfakhry
Forgor to mention that your device is a G4
Dear
How did you know that my device is G4
thanx
G3 or G4
If your SPl ends in .000 then it's a G3
If it ends in .0000 or .0001 thens it's a G4
dear
You are very helpfull thanx for you
Dear
I read in wiki that if its end in .000 is g3 and .0001 is g4
http://wiki.xda-developers.com/index.php?pagename=prophet_g3g4_how
so mine ends with
Spl 2.20.0000
so it must be g3 that right or not
thanx again
I also facing d similar problem like bro malfakhry. After flashing back to Qtek NVID Rom WM5 it go hang....and it show
IPL 2.20
SPL 2.20.0000
GSM 02.47.21
OS 2.20.7.34
May I know my device is G3 or G4?
How myself gonna to solve this hang issue?
Thanks in advance.
rgrds
lrew9999
G3 or G4
Hi All
If your device was a G3 the SPL can only end in .000
As your devices end in .0000 it is a G4
When you flashed the NVID rom this means there is no vender identification and will reset your SPL back to 0 all you do is count the noughts as it can only be 3 or 4 this then gives you the G rating.
If your phone hangs after this flash then try a hard reset first if it still hangs just go through the whole proccess again from the start remembering the hardSPL and when done perform a hard reset.
Dixiesmu said:
Hi All
If your device was a G3 the SPL can only end in .000
As your devices end in .0000 it is a G4
When you flashed the NVID rom this means there is no vender identification and will reset your SPL back to 0 all you do is count the noughts as it can only be 3 or 4 this then gives you the G rating.
If your phone hangs after this flash then try a hard reset first if it still hangs just go through the whole proccess again from the start remembering the hardSPL and when done perform a hard reset.
Click to expand...
Click to collapse
Dear Dixiesmu,
Its work now!!!
Thanks a million.
Hi to all,
I have strange problem with my HTC surround.
I unlocked it and install 7.5 ROM ... strange thing is that I just use soft SPL ( just for installing )
and now I have working ROM and everything is work fine ( in OS )
but when I go to boot loader ( three colors ) I have see only 1 row .. that is no SPL data and no serial or USB communication,
so I can't change ROM or do anything else !
Please, help me to fo find out what may cause the problem
Regards
Look at this post, it talks about half bricked spl
http://forum.xda-developers.com/showthread.php?p=21247026#post21247026