Related
Hi people,
I have a mayor problem. I just fu*ked up my phone by installing WM6.
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me!
s200 off
and I have this problem. my phone is off by installing new spl
Now the screen freezes when the QTEK "Keep the world in one" logo is visible with the OS Version information. Hard reset wont work.
How can I restore the original rom ?
Please help me
To go in the boot loader screen you have to:
press & hold camera and commmanager button
press the softreset hole
release the commmanager button and keep hold the camera button until the 3 colours display appear
Byez
but wat can i do after i hav the 3 colour screen come out?
pls help..... i'm very nervous..... i don wanna waste my money coz i screw up my phone.,...
i'm now outstation... can go back to the service center within this 6 mth....
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
mrsurya2000 said:
Connect USB Cable. Go in the Boot Loader screen (Hold down camera button, power button and soft reset until the 3 colours display appear). Run Rom upgrade Software.
Click to expand...
Click to collapse
Which rom upgrade software ?
de.schurk said:
Which rom upgrade software ?
Click to expand...
Click to collapse
http://www.romupdate.ru/ghjibdrblkz...rophet_220734_2207114_024721_QtekWWE_Ship.exe --> this software
don't worry, your device isn't bricked as long as you can run it in bootloader
check in WIKI if you have G3 or G4 Prophet
I'm the exact same situation.
And wiki didn't help so far...
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
namco said:
Take it easy and flash the ROM as described. Use any WM5 ROM compatible with your device, but preferrably one with no vendor ID. In case you cannot update normally use the RUU-No-Vendor-ID application found in the FTP.
As said above the device is not dead, it can be recovered.
Click to expand...
Click to collapse
Bear with me on the dumb questions
It looks like I managed to re-install
Thank you for your help. I installed the rom dezzer advised (post 7 of this thread) and it worked fine. Does that mean tha NOW i can flash smart1 1.3's?
Yep. Turn off the phone, make it sync with activesync and run UPDATE_ROM.bat.
Then cross your fingers Kidding. It will surely work. Remember to hard-reset after the upgrade.
If anything goes wrong just reflash WM5 and hard-reset. Always hard-reset after ANY OS upgrade.
Hi: This is my first posting and I am new on this board. I have had an MDA that I got as a gift from my Dad and I love it. However, I used it last week and for some unkown reason, it is stuck in the:
'Press Send to Restore Factory Defaults, Other Key to Quit.'
I have been trying to get past this for 4 days and am not having any luck.
I got to the Align Screen and that happened only once. Then I could not get past that. It keep showing the Align Screen and I kept tapping and it just kept going round and round from the Center Tap to the sides and back.
My battery is fully charged, I have read this forum and still I am lost. I would really appreciate any help. Thank you so much.
Toni
Do a Soft Reset or Hard Reset.
Cheers!
zabardast_1 said:
Do a Soft Reset or Hard Reset. Cheers!
Click to expand...
Click to collapse
Thank you for trying to help me. However, I have done both of the resets over and over and I keep getting the same result. 'Press send to restore factory defaults, other key to quit.'
I can get no further than that display regardless of what key or keys that I hit.
I have even tried the two ways of doing a Hard Reset:
1. Hold Com and Voice while pressing Soft Reset Button for 5 or more seconds until I get that display.
2. Hold Com, Voice and Camera while pressing Soft Reset Button for 5 or more seconds until I get that display.
I cannot get past that display regardless of what key or keys I press.
It seems frozen at that display point.
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Tonis said:
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Click to expand...
Click to collapse
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
sleurhut said:
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
Click to expand...
Click to collapse
Did a search for Love Rom and Wizard_Love ROM and only came up with 103 results consisting of some Threads with 1570, 898, 618,787, 893, 464........postings on the first page for Threads 1-25.
Now I do have a Red, Green, Blue, White Screen with RUU in the top right corner of the Red Bar with IPL 2.26 and SPL 2.26 in the Red Bar. Nothing is in the Green, Blue or White bar.
I tried to Hard Reset and Soft Rest and nothing happens. I removed my Battery and then tried again and still nothing happens?
Where can I find Wizard_Love ROM and what do I do when I find it. My PC will not recognize my MDA and I used WST and that cannot located my MDA.
I am at a complete loss of what to do next.
Thank you in advance for taking the time to try to help me get my phone operational.
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
Thank you again for your help. Prior to this posting I found:
epimazzo Posting at: http://forum.xda-developers.com/showthread.php?t=294107&highlight=bootloader #1 and this is what cleared up my problem and now my MDA is running GREAT!!!!!!!!
This was the same thing that you posted for me, too.
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode (Red, Green, Blue, White Screen) and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
1. Make sure your Phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your Phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
So, Thank you all for your time and help. I do hope this helps others to find a way to correct their problems.
Thanks !
Yes.thats exactly what I wanted you to do
I'm glad you got it up and running fine
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
I does everything you do but
I don't have the cradle :S
so that means a problem?
or there a nother way?
Hi!
I got an mada vario 4. How can I upgrade the rom on it? Or can I change the t-mobile touch flo to manila 2.5? Thx! Zoli
Help Help Help
Iam new to the flashing
I have herald (HTC P430 HERA) with wm5 ,i tried to upgrade to wm6 with TOUCH-IT.I installed the SPL and then ran the RUU ,everything was perfect the installation started normally ,durin the installation i chose the option to use the keylock ,when my htc started it kept on asking me the password on the device which i entered but it did not accepted .i kept on trying and eventually took out the battery.When i restarted the device it got stuck on a green scnreen with spl 1.08.0001 and when turned off i tried going in to the bootloader but everytime i run the same ruu it gives me erorr 300 i have tried several times now, donwloaded each and every ruu but all in vain and im in pain .sometime the screen get stuck on 0% . Can somebody help or atleast direct me to the right area.
at least it we could reach 1% rom update can be done
i think we can handle it via bootloader commands
you need to install enablerapi....
.......................
You have to download the official Tmobile RUU (google it), and reinstall it. After that before you try to flash your phone you have to take the Enablerapi cab and put it on your phone. After that do a hard reset. If you dont know what that is by now you shouldnt be flashing your phone. But anyway hold the buttons above the talk and end buttons and press the reset button at the same time. A black screen will come up and ask you to press the talk button (green button), press it and the phone will do a reset. Configure your screen and connect phone to active sync/WMDC and make sure you put the phone in airplane mode. Then run the uspl again and follow the directions on the screen.
First of All, I am Noob for all this flash phone stuff~~
I was using A-Unlocker last night on my Athena, however the phone got f**ked up
I was able to finish the Step 1 "Flash SPL". After I done with Step 1, here is I got from bootloader 3 Color Screen
ATHE 100
IPL-V1.00
ATHE100
SPL-V1.20. Olipro
and it unlocked Step 2 "Unlock Radio"
after the Step 2 there was a Notice popped up "Your Device must now be unlocked with a program, please configure your device and then connect and sync with Activesync. after doing so, click OK and watch your device screen"
and My phone stop at HTC loading screen, not able to boot to "Window Mobile" system. I did reset phone many times but didn't work.
Please Help Me Out here~~ Tyvm
p.s: I can still boot the phone to bootloader 3 Color Screen
please help me
Your device is okay. You can already proceed to flashing any ROM that is desgined for SPL 1.2. If you want just a good looking ROM, you might want to try PK3.0 ROM. If you want WM6.1, try irus ROM.
If I'm you, I'll skip any rom that uses SPL3.5 for the time being until you're sure there is a mean to come back to SPL 1.2. This mean you should skip AP4.0 for the time being.
To flash one of the SPL1.2 based ROM, remove your storage cards and SIM cards, and ensure your battery is close to full. Then get into Bootloader mode (by pressing down the Camera and poke into the reset hole - hold it down for a good few seconds until you see the tr-colored screen). Then connect your cable until you see USB on the device screen. Then on your PC, start the RomUpdateUtility program and follow the instruction on the PC.
Good luck.
Thx, man! U Rock!!
Just flash the phone with PK3.0 Rom~
I brick my phone ,now ,white screen start, not enter sys,can be link by pc!!please give a newer uspl!!thanks....
Hey buddy, can you give a little bit more info. Were you trying to flash your phone? If so, did you the PDF directions?
white screen experience
Brief experience:
1, my phone is the original shadow , English system.
2, would like to refresh the Chinese
3, in the absence of support shadow that use the Dopod c730'uspl refresh the shadow'uspl, lead white screen
4, the current machines can not be normal start, the start-up is white screen ; hold down the camera key and link usb phone can be connected computers, and can access to refresh uspl interface.An error come when use the latest uspl of shadow refreshing ," this update utility cannot be used for your shadow ,please get newer update utility"
Turn of your phone, press the two soft keys and press the power button, then let go of the power button while still holding the soft keys. Then you will get into the tri-color boot screen. Then try to flash your phone again.
He says that he had flashed the wrong SPL.
The SPL is for HTC S710(vox) only,but he flash it into his T-mobile shadow.
The SPL still at work, can be connected with MTTY
but can not reflash official rom with RUU.
hikei say right
As the situation heiki said, master guide
who can help me!!
please help me!!!who can make a rom for my shadow!!!
Don't listen to previous posts
The Previous posts on how to fix this porblem are not correct. If your shadow gets a white screen, or will not boot windows fully, you will have to either reset the OS to defaults, or reinstal OS completely.
The First option is to Reset the OS to default this can be done by following these steps:
1. turn off the phone
2. Press and hold the two soft keys that are right below the LCD screen. (These are the keys above the Home Key and the Back key)
3. While holding these keys, press and release the the power button, this should turn on your phone, if not try again. (do not keep holding power key, but continue to press the soft keys)
4. A screen will then appear asking you if you want to reset your phone, press the Send key (The Key with the Phone on it)
5. The OS will then begin to reset. If this does not work, follow next option.
The Second and only other option is to perform a rom flash. You will need the original tmobile shadow rom. I've tried with several hacked roms, and they never finish while doing this. Download original rom from here:
http://wiki.allshadow.com/index.php/Downgrading_to_WM6.0/_Neo_on_the_Shadow_2007
Now you are ready to fix you problem.
1. Turn off you phone
2. Press and hold the Camera Button on the side of the phone. (press no other button with it)
3. Now press and release the power button (phone should now turn on, if it does not, try again. Do not release the phone button)
4. After phone turns on, it will then show you a Colored bar screen, this is knows as the Boot Loader screen. It has a similar purpose as the Boot Loader and Boot Select screen that is seen on PC computers.
5. Place phone down in secure location, and connect to your computer. (drivers may install after connection, let them install before moving on)
6. Open the Shadow Rom update utility that you downloaded before and follow prompts.
7. Once update completes you are now ready to use your Shadow Again. If you want a different Rom, go ahead and download and follow instructions for installing that rom.
Things to avoid this in the future:
1. ensure you are updating rom with phone on a secure surface, ensure it will not fall and disconnect from Computer during update.
2. ensure battery is full
3. use roms tested and validated by other users. Read reviews of problems and known issues.
4. Use tested, validated, and/or signed apps. (ensure apps are meant for smartphones with QVGA and windows mobile standard. Generally this is not a problem, but better safe than sorry)
So that is a step by step guide on how to fix your problem. good luck
Will this also help me?
Zephnath,
I'm pretty ignorant when it comes to my phone, but I upgraded to WM 6.1 a while ago. If I follow your steps to re-load the original rom will it also go back to WM 6.0? If not, do you know how I can change my phone back to WM 6.0?
okiesho said:
Zephnath,
I'm pretty ignorant when it comes to my phone, but I upgraded to WM 6.1 a while ago. If I follow your steps to re-load the original rom will it also go back to WM 6.0? If not, do you know how I can change my phone back to WM 6.0?
Click to expand...
Click to collapse
Sorry to keep you waiting, but if you follow the steps above and you use the rom downloaded from this link http://www.sendspace.com/file/thvf9u you will have your phone set back to the original rom issued by t-mobile.
If you installed, or tried to install a rom not from tmobile, you will have to follow the second step I provided.
If you have not attempted, or do not have a rom that is not from t-mobile, then follow step one.
If you are not sure, follow step two, by first downloading the file I posted a link to above
Edit: Following these steps will put you back to Windows Mobile 6.0
So you're saying that the SPL from the OEM rom will overwrite the SPL from the Vox? I always thought that flashing a SPL from the wrong phone would brick it for sure with no takebacks.
tonyc0642 said:
So you're saying that the SPL from the OEM rom will overwrite the SPL from the Vox? I always thought that flashing a SPL from the wrong phone would brick it for sure with no takebacks.
Click to expand...
Click to collapse
What I am saying, is that following these steps will get you out of the whole with the white screen of doom, if you follow them. I've done this on not only one shadow but on two, several times. When going back to original rom, it works just like it did out of box. (Slow and clumsy) But at least you have your phone back, and with MyFaves again.
When you go back to the original rom, provided via the download link from previous post, the phone is as it was when you first got it. (Including the SPL, so if you want to flash a different rom on the phone you have to unlock it all over again.)
People have done this many of times. Often people have hardware problems and need to send the phone back for warranty fixes, but waite, they flashed their rom to 6.1. That voids their warrenty. So what do they do now? I know, they flash it back to 6.0 using the official update (the link I included) that t-mobile provided. They send their phone back to manufacture and get their replacement as if their old phone never saw a different rom.