How do you guys listen to your voice navigation software? I have the supertooth II BT handsfree set, and make and receive my phone calls through it. Now when I go into my nav software, the audio goes throught the loudspeaker, or I have to use the cable earphones (supplied with phone).
Using the earphones is a bit stupid, then I might as well not have the handsfree in the car. I would like to get all audio & sound to go to my Supertooth.
There was a site I found where a guy posted software that sends all audio to a bluetooth headset. Now this was a Samsung i730 post, now I wonder if it is not written for the i730, as I tried it out, and it switches my Supertooth on, but still nou audio can be heard.
Will something like a BT audio transmitter that is normally used to trasmit audio from a MP3 player to a hifi work?
Hi,
I have never owned a BT headset before, so I have some questions if you are willing to help me.
If I read some specifications (for example from Jabra BT8010), a BT headset could have 2 modes :
- Phone mode (mono)
- Music mode (stereo)
What is exactly the music mode? Does it mean that it controls Windows Media Player?
Or it has its own media player?
How if I want to play VIDEO (using Tcpmp for example), can I use the Music mode?
Mostly I will use the BT to watch movie and play games ....
PS: Do you use Jabra BT8010 with Kaiser? How is it?
Thanks,
since i know how frustrating it can be not to get an answer..maybe you prefer a soso answer to no answer...;-):
i used to have a stereo headset nokia hs-12 or so...but this is already some time ago...
so the way it basically works: upon pairing it will say that it supports music and phone.
depending on the layout of the headset (and the achieved compatibility with the handheld device) you will be able to control some to most features of the media players in the device. like play, pause vol up vol down, FF, RWD.. my headset worked well with windows media player, also with resco radio..tcpmp i did not have at that time yet.
hope this gives you an idea.
Andy
I think the difference is that the Phone Mode or Mono mode means that there is only ONE audio channel... suitable for making and receiving calls while the Music mode or Stereo mode means that it has TWO channels which is suitable for headphones because they have to channels.
Phone Mode BT devices can play your music but only out of one channel and in all cases Phone Mode BT devices only have one ear plug.
Music Mode BT devices can play your music or any sound for that matter out of both channels which is why they are in headphone form with two ear plugs.
MONO=1
STEREO=2
This is my take on this but please correct me if I am wrong as I would too like to get to the bottom of this.
actually that is not correct.
the so called A2DP profile is AFAIK only supported by stereo BT headsets/headphones. a mono headset will NOT get any audio sound under normal circumstances. However one can tweak the registry -and there is also software that does it - in order to direct the audio output to the headset.the price for this being, that as long as this function is active, voice dialling from the headset will not work, since this is the function that is being used to switch the audio gate.
Now, in the case of the 8010 this should be different, since it is basically a stereo headset with a detachable 2nd earpice. this one should therefore always work in A2DP mode and therefore enable audio throughput without any further tweaks.
I just picked up a BT8010 yesterday -- my local Fry's had them half-price. Stereo performance is pretty good, but there's a bit of skipping (i.e. momentary dropouts of the audio). There's a firmware update available from Jabra -- that may help.
Haven't had the chance to use the BT8010 as a phone headset yet, so I can't address that.
I just found that while I had my bluetooth hbh-pv740 mono bluetooth connected and played music via media player on X1i, I pressed call button on headset and voice command went to stand by.... the I said cancel and for about 5-7 seconds the music resumed in my bluetooth headset. Then is went back to the phones' speaker.
Does anyone know of a registry hack to make it stay in the mono headset and not go back to the phone?
Or even better, make the sound come out the mono bluetooth in the first place?
Would be great somehow.
You can try a software BlueMusic.
Version 3 can use with X1.
SUPER. Thank you very much, tried and just bought this thing! Works great! I knew somehow it WILL be possible to play music over a mono bluetooth! Thanks again!
Hey guys, thanks in advance. I've done some searching and haven't been able to find anything that addresses a small oversight.
So I have an A2DP audio receiver connected to the auxiliary input in my car. It works great for music, Pandora, and what not, but none of the mono-channel phone audio gets played through my car speakers. I realize it's due to the different profiles, that A2DP was designed for music and the hands-free profiles were designed for phone calls. However, I've been able to find Music --> Mono software that allows me to play music through mono-channel non-A2DP headsets.
Is there anything out there that can help me divert the mono phone audio stream through to A2DP?
Thanks.
-HD
With a connected Stereo-Bluetooth-Headset i can hear all Audio from Music or the StreamingClient for Ampache in this Headset.
But all Audio from Video or Xanox-TV it will play Audio only with the Speaker.
Connect i the cabled Headset then it plays all in the cabled Headset.
It this an Tweak in the Registry for Windows Phone 7.5?
The Phone is a LG-E906 with Windows Phone.