Hello xda!!
I am very much a newbie and now I find myself with a brick of a phone. I wanted to put a new rom with the touch flo on it but it did not work. I upgraded to the SPL 3.08 I think that the right number and then I try to download the diamond 2.0. However the ROM did DL correctly but when I wne to configure it it said windows.autoconfig not found on my 8125 wtf is that all about. I own a cingular 8125. I dont know where to start now. All I want is the touch flow rom but how and where do I start. I even tried to flash it back to the HTC OEM rom but I could not do it. Please anyone?? Help por favor....
Regards,
David
I would try to help you, but you will need to type (give) more information that those that I give/ask you. I'll need to know
- Your phone, G3/G4, IPL/SPL/OS/Radio
- The OS you flash page, instructions followed
- Your PC OS used
Read the Wiki (on top of this page, XDA-Wiki) on Wizard section on how to un-brick your phone.
I have a g3 type but I dont have the phone with me. I switched my sim to my treo for now. the OS ROM I tried to flash it with was Diamond 2.0 my SPL 3.08. Any help would be greatful
As I said in my previous post, you'll need to give me more info. Example of more info http://forum.xda-developers.com/showthread.php?t=339014
UPDATE:
How do downgrade http://forum.xda-developers.com/showthread.php?t=335222
I have a Cingular 8125 and the ROM I currently have is a Wizard Love/ AKU 2.3
When I turn my phone on it reads this
IPL 3.08
SPL 3.08
GSM 2.25.11
OS. 2.26.10.2
This is what I wanted to do. I wanted to put WM6 with the Touchflo on it but now I am stuck with this ROM I know nothing about. When I try to flash it back to the Cingular ROM is will not update I need a new NBF file? If you can help I would be greatly thankful and would donate to you.
Cheers,
David
Hi!
I have a problem. I installed WM6.1 on my VPA C2. Everything went fine, but WM6.1 seemed to be slow on my device. So I decided today to downgrade to the original Qtek AKU2 WM5. After I was done downgrading my VPA is not booting and hangs up on the provider screen with the Vodafone Logo.
Here my facts:
IPL 2.21.0001
SPL 2.21.Olip
GSM 02.19.11
OS 2.18.7.7
Please tell me how I can reactivate my device.
Soft- and hardreset didn't work.
Greetings,
Chris
moiney said:
Hi!
I have a problem. I installed WM6.1 on my VPA C2. Everything went fine, but WM6.1 seemed to be slow on my device. So I decided today to downgrade to the original Qtek AKU2 WM5. After I was done downgrading my VPA is not booting and hangs up on the provider screen with the Vodafone Logo.
Here my facts:
IPL 2.21.0001
SPL 2.21.Olip
GSM 02.19.11
OS 2.18.7.7
Please tell me how I can reactivate my device.
Soft- and hardreset didn't work.
Greetings,
Chris
Click to expand...
Click to collapse
Your phone is HardSPL,did you first remove it before flashing wm5 ? if not than you have to first remove the HardSPL flash back to official original vodafone IPL/SPL and than flash official wm5.
Well,you are lucky,if it still boots up or goes into Bootloaders,coz flashing a rom with IPL/SPL even if its an official rom, to a HardSPL device will 'Brick' the phone.
Now,if it still gets into Bootloaders,reflash any custom build wm6 or 6.1 rom to recover the phone,than remove HardSPL,flash back to official IPL/SPL and than revert back to wm5,hope it'll work out.
@zabardast_1: Thank you for the fast answer!
Okay, I now flashed the phone again w/ WM6.1. Everything works again.
What do I have to do now to get WM5 back on the device? I don't want the Vodafone ROM, I want the Qtek ROM. How can I remove the Hard SPL so?
Greez,
Chris
Read and do the method explained in this thread and remove HardSPL :-
http://forum.xda-developers.com/showthread.php?t=342744
The Mighty Search
...knows all!
Hint:
try "remove HardSPL"
Thank you all!
Everything is back on WM5 and working!
Thanz!
Have a nice day
Hello! I want to upgrade my Qtek 9100 with the latest ROM version. I have the official Qtek ROM 2.17.7.2 WWE, IPL/SPL 2.17, Radio 02.07.10 and AKU 2.0. Where can I find the latest official Qtek ROM?
How does the IPL/SPL influence 9100's performance or stability? I have found IPL/SPL version 3.08. Can I install IPL/SPL 3.08 separately from ROM version? Can I damage the Qtek?
And the most important thing: I want the latest official AKU installed on my Qtek. Can it be installed separately from ROM? Where can I find it? If it can't be installed separately, please help me to find the latest official Qtek 9100 ROM packed with the latest official AKU version.
One more question: Is the radio version a good one? Is there a better version? Can this be installed separately?
I think that is best for PDA that AKU, IPL/SPL and radio to be installed with ROM, not separately. Is that true?
Thank you very much!
Look at you men!!!
are you insane?
Jajajaj read men!
but as I am very good person I will tell you where you need to read ok?
First!!!!
Where can I find the latest official Qtek ROM?
Click to expand...
Click to collapse
So i think you were found the 3.08 is good but is not recomended yet.... ok.
Second!!!!
How does the IPL/SPL influence 9100's performance or stability?
Click to expand...
Click to collapse
It don't influence in nothing my men! nothing... why... because AKU (Actualization Kit Update) was just for wm5 ok? its like you wanna see if XP SP3 works well with your new Windows Vista Ultimate edition...
But you need to read the tutorial first to know how to downgrade first to1.01 then unlock, then upgrade to 2.XX not 3.08 ok?, then to a new WM6.1 rom ok...
Third!!!!
I have found IPL/SPL version 3.08. Can I install IPL/SPL 3.08 separately from ROM version?
Click to expand...
Click to collapse
Ok you found the 3.08... yes you can but is more important ask... what chipset do you have? G3 or G4? please provide us with this info first... i saw you have 2.12. bal bla bla so is a G3 but confirm cause some people said I have IPL SPL 2.17 and NOT they have 2.17.0001 (G4) and they has a bricked phone... so the only way to upgrade or change the IPL or SPL is flashing an Original ROM maded by your carrier and for your chipset ok? well... so the answer for this question is NO men!
Fourth!!!!
Can I damage the Qtek?
Click to expand...
Click to collapse
Yes the IPL and SPL changing system is the problem for all thats why people bricks their phones so please dont use it cause it wont lets you perform speed or something ok? AKU's was History Now! the world of WinMobile rules the 6.1 with .Net compact 3.5
Fifth!!!!
Can it be installed separately from ROM? Where can I find it? If it can't be installed separately, please help me to find the latest official Qtek 9100 ROM packed with the latest official AKU version.
Click to expand...
Click to collapse
No is not the most impoprtant question is the same but all in one hahahaha
No you cant upgrade separately... aku is history so dont try to upgrade stay in Aku 2.XX after your unlock process ofcourse and read a lot men you need to read a lot!
Oh sorry i forget something... you have the last the 3.08 AKU 3 (3.08)
The AKU2 comes with A2DP stereo sound bluetooth via Headsets
The AKU3 comes with A2DP and Direct Push tecnologies... so... they never works in WM6 or 6.1 why? cause it already have it by default....
Hope it answers all your question and please men I cant tell you where to go if goes to G3 tutorial for unlock or G4 hardSPL cause you dont have read to fill your signature with your info so...
Be cool men and Good luck we are here to support!!!!
No, I haven't found 3.08 ROM. It's only IPL/SPL 3.08. I have found T-Mobile 2.26 and I don't know if it's good or not. Does T-Mobile ROM differs from Qtek ROM? Thanks!
So...
So... what do you mean with this...
I have found IPL/SPL version 3.08. Can I install IPL/SPL 3.08 separately from ROM version?
Click to expand...
Click to collapse
The IPL and SPL cant be found separately men!
where is the one you found post the link please...
I have found T-Mobile 2.26 and I don't know if it's good or not. Does T-Mobile ROM differs from Qtek ROM?
Click to expand...
Click to collapse
Men!!!
With the Original ROM T-mobile 2.26 you will have the 2.26 IPL and SPL...
And with the Original ROM T-mobile 3.08 you will have the 3.08 IPL and SPL...
This components arent separately.... Never!
It diffiers from Qtek in many things like... some apps... Splash screens.... Configurations... and many little things.
Here all recomends to Use the T-mobile Rom 2.26 to Upgrade after the unlock process cause is the best Original BASE rom ( is the same but is highly recomended that after unlocks the CID and SIM use the IPL and SPL 2.26)
I have found the 3.08 IPL/SPL in the unlocking thread...I'l give you the link latter because I am in a hurry.
If I want to flash the T-mobile 2.26 over Qtek's 2.17, I have to go back to 1.05 ROM and CID unlock, or I have to install the 2.26 over 2.17?
How about with battery life in T-Mobile 2.26 when using wireless and bluetooth? When using only GSM, the battery drains fast?
Thank you very much!
I think here...
Here is your link... so
http://forum.xda-developers.com/showthread.php?t=311027
Whatever...
You are on qteks original 2.17 is it truth?
So... first of all downgrade to 1.05 (you dont need to upgrade to SPL 2.26)and do the unlocking process, if everything is ok...
second... upgrade to 2.26... then your favorite Coocked Rom by whoever you want ok?
third... everytime you want to upgrade or change your rom is highly recomended to flash first an Original ROM qtek 2.17... Tmobile 2.26 or 3.08 then your new Rom coocked ok?
You can change for every Original to Custom and viceversa now, and you dont need to downgrade again to 1.XX again cause its unlocked forever.
Hope it respeonds your doubts... The issue on many ROMs for this kind of things dont be the same on Original ROMS (I didn see issues on originals, well maybe the speed and performance), and many chefs recomends Three steps to upgrade if you experiments this batt drain issue:
1.-Before the NEW rom, Downgrade to any original
2.-Be sure your Batt is FULL I mean (100%)
3.-Let your device synchronize fully when it starts after an upgrade ( I mean dont unplug at the end of upgrade procedure)
Ohhhhhhhhhhhhh
God damn ****!!!!!
Men wait a minute you are G4!!!!!!!!!!!!!
You dont need to do this unlocking proces ok?
it will be brick your device
Your device is G4!!!!!!!!!!
You need to go to G4 forum and perform the HardSPL Patch ask there....
Well my prays was listening hahahahaha
Because you write your info on your signature we avoid to brick your device
forget all this ****n thread and start again asking on G4 forum please god damn!!!!!!!!!!!!!!
I have a G3 device and I have CID unlocked my phone before, when I upgraded from Button 1.5.4.2 to Qtek 2.17 (I have followed the steps in the upgrading "manual" from here http://forum.xda-developers.com/showthread.php?t=285435). So, I think I don't need to go back to 1.05, unlock and then install 2.26. All I have to do is simply to upgrade T-Mobile 2.26 over Qtek 2.17 with RUU utility.
Now, I don't know how T-mobile 2.26 will influence my phone's settings regarding that I live in Romania and I am a Cosmote mobile network user, not T-Mobile. I have seen on a web site that you can not connect to Wi-Fi hot-spot if the hot-spot isn't from T-Mobile. Is T-Mobile ROM 2.26 restricting the phone's settings and the choice to freely connect to wireless hotspot or Cosmote GPRS and MMS, Orange EDGE and MMS. Can I add new SMS, MMS or GPRS/EDGE settings? Or they force you to use their settings and data connections?
Thank you very much!
So xtrange
The IPL and SPL you have on your signature are for a G4.
No it is recognized by the SIM Card... i mean the sms and cellphone conections but mms gprs and other things yes... you need the configurations separately...
So T-Mobile ROM will work OK with Cosmote network... But does T-Mobile ROM restricts any of the device's function? Can I use all it's function freely (wi-fi, bluetooth, irda -I'm asking you this because I have played with an HTC Prophet from T-Mobile that wasn't wi-fi enabled)? Can I install all kind of programs? Do you know anything about battery life?
In a previous post, you said that after CID Unlock it is recomended to use IPL/SPL 2.26. Can you, please, tell me why?
About G3/G4 chip: when I have verified chip version on SYSTEM-DEVICE INFO it showed M-System G3. Now It only show M-System without the G3. Don't know why...
Thank you very much for your help!
Andrei__1 said:
So T-Mobile ROM will work OK with Cosmote network... But does T-Mobile ROM restricts any of the device's function? Can I use all it's function freely (wi-fi, bluetooth, irda -I'm asking you this because I have played with an HTC Prophet from T-Mobile that wasn't wi-fi enabled)? Can I install all kind of programs? Do you know anything about battery life?
In a previous post, you said that after CID Unlock it is recomended to use IPL/SPL 2.26. Can you, please, tell me why?
About G3/G4 chip: when I have verified chip version on SYSTEM-DEVICE INFO it showed M-System G3. Now It only show M-System without the G3. Don't know why...
Thank you very much for your help!
Click to expand...
Click to collapse
IPL/SPL: 2.17.0000
These are G3 Bootloaders,if it was 2.17.0001,then it wud have been a G4,therefore,your device is a G3 phone.nothing to worry about.
Now,you can flash any official roms to it as all the officiall roms like Qtek,t-mobile Cingular or O2 are basically the same roms provided by the Microsoft,they have the same Base Roms,but just all the vendors add up their own stuff to it.Like Splash screens,programs/applications and network/gprs settings.Apart from these ,there is no major difference in any Official rom from all the vendors.
Yes! Bootloaders(IPL/SPL)/Radio Roms can be flashed separately or within by a Rom flash.
Downgrading to IPL/SPL 1.xx is only needed if you want to CID unlock the phone for upgrading to any wm6 or wm6.1 rom,as no official wm6 rom is provided by any vendor.So its only possible to upgrade to wm6 or 6.1 latest rom through custom build roms and for that its required to get the phone CID unlocked
After getting the phone CID unlocked,its prefered to upgrade to T-mobile 2.26 coz its a proven stable base rom,but you can also upgrade to IPL/SPL 2.xx,required for upgrading to wm6 by flashing any other official Aku (Adaptation Kit Update) 2.xx rom.
Upgrading to IPL/SPL 3.08 will just give you a slightly better boot up timings,which is hardly noticeable and nothing else,so if you are at 2.xx,its more preferred.IPL/SPL 3.08 sometimes creates problems afterwards if you have to downgrade.
Its also not necessary to reflash back to official ro each time before flashing a new rom,but only recommended,to clear the Extended_Rom corruption and have a clean base,I have never reflashed any official rom before flashing any new rom,but then thats me!
Thanks men!!!
Im getting worried but... why does the Bootloader Shows the four zeros... on my device it never shows the zeros.
In 2.17.0000
I think he use the WST isnt it? not seing the bootloaders...
I have finally installed T-Mobile 3.08. It has interesting features, but I don't like the dialing pad and that when I start Internet Explorer, the phone asks if I want to connect to T-Mobile GPRS. I'm 60% with the Qtek 2.27 and 40% with T-Mobile 3.08. I'll wait to see the battery life compared with Qtek ROM and the power consumption when using wireless. I'll make a decision in weekend.
Oh, forgot to ask about WM6. Will the phone be faster or slower? What are the main differences from WM5? Is there an official WM6 ROM?
Thank you very much!
It seems that qtek's wi-fi is connecting continously, without establishing a connection. It show "connecting" all the time.
Today I have installed Qtek 2.17 ROM. I like it more than T-Mobile 3.08.
Dear all,
I have a HTC Charmer (t-mobile, German) and I am trying to change the ROM to an english one. I already managed to unlock the phone with Lokiwiz 3.0a but I didn't have any success at all trying to get a WiMo 5 ROM. Does anyone know where can I get one? I found one in t-mobile website (uk) but when I'm installing it, it says "invalid vendor ID".
I read in other threads that Prophet ROM may work.
http : //forum.xda-developers.com/archive/index.php/t-343356.html
However, I'm not sure if it's true and I'm afraid of obtaining a cool brick as an outcome.
Many thanks,
N
Next time just read and if you ask give more info. Which SPL and IPL do you have?
And to flash the English Aku3 to a German phone you need the NoID ruu. You can get it here: http://forum.xda-developers.com/attachment.php?attachmentid=42657&d=1183226200
If your SPL is 2 or higher I would recommend you to use an English WM 6 6.1 or 6.5 instead as they can be found in Charmer Mobile 6 subforum.
Before you flash WM6 or higher please read how it works. (The CID unlock part of the one howto isn't needed to be done!!)
Hope that helps.
And next time please read first and ask then!!!
have down grade my MDA compact 2 to WM 5 RUU_Charmer_38221_382116_026921_TMO_UK_WWE_Ship rom supplide by T-mobile and tried flashing it to 6.5 but it didnot work, now tried ur ROM to flash it to wm 6.1 but it get stuck at
while showing the following information;
IPL: 3.08.001
SPL: 3.08.001
GSM ; 02.60.21
OS : 6.1.0.0
Can you tell me what might have gone wrong.
Can you please help me.
Can you suggested any Cooked ROM which can i flash on to my charmer which is on WM2005 at present.
unforgetable0708 said:
have down grade my MDA compact 2 to WM 5 RUU_Charmer_38221_382116_026921_TMO_UK_WWE_Ship rom supplide by T-mobile and tried flashing it to 6.5 but it didnot work, now tried ur ROM to flash it to wm 6.1 but it get stuck at
while showing the following information;
IPL: 3.08.001
SPL: 3.08.001
GSM ; 02.60.21
OS : 6.1.0.0
Can you tell me what might have gone wrong.
Can you please help me.
Can you suggested any Cooked ROM which can i flash on to my charmer which is on WM2005 at present.
Click to expand...
Click to collapse
Hi!
You need 2.06 IPL,SPL to flash cooked ROMs.Downgrade is risky,I did it,but it needs some knowledge.
Before do anything with your Charmer,make a Goldcard,it can be useful!!!
http://forum.xda-developers.com/showpost.php?p=5612551&postcount=38
BR
Scootie
Hi,
Please help me guys.
Last night I flashed TNT ROM into HTC WIZA200. While installation, everthing was going perfect but after reaching at 99% it gave me "error 302".
I searched every where about this problem. So I got that my Wiza200 was not CID unlocked .
now I know that before loading any custom ROM, I must have to unlock the CID/SIM lock.
Now my Wiza200 is stuck at 3 color screen. Now the solution is that I have to load the OFFICIAL ROM of the Wiza200.
I search every where the Official ROM. But I can't find it.
PLEASE HELP ME... If anyone have the ROM for my Wiza200 please please share me the link....
my device is G3
IPL : 1.05
SPL : 1.05
PLEASE HELP ME....
THANKS IN ADVANCE
here is the offical T-Mobile 2.26 rom
also you should read this thread
good luck