Database Users

Internet via bluetooth?

Hi all
Firstly apologies if this has been discussed elsewhere. Searching bluetooth returns ... too many results to sift through.
OK, I have this setup. I connect my laptop to the net using either the router OR network cable. My laptop is equipped with BT.
Is there any way to browse the net from my PDA, by establishing a BT connection from XDA2 to the Laptop?
I know it would be a doddle (I hope) if I were to purchase a wifi SD card, but if I can avoid the expense it would be great.
Thanks in advance.

One way would be through BlueTooth ActiveSync. As when in the cradle, when your PPC is connected to your PC through ActiveSync, internet connectivity is through the PC. I use it whenever I am in proximity to my BT laptop. Works well!

If you go to Options in ActiveSync, click the Rules tab, check Open ActiveSync when my mobile device connects. and have the Connection set to The Internet or Work depending how your network is set up. Then establish an ActiveSync connection (USB, serial, Bluetooth or IrDA) and it will allow you use Internet programs like PocketIE, Pocket Outlook, etc.[/b]

I thank you both for your very very quick response.
Yes, both methods work. YIPEEEEEEEEEEEEEEEEEE
I am one happy bunny.
Cheers

Going insane bluetooth activesync internet
I wish I could be so happy. Let me give a brief overview of the last 6 hours:
Installed bluetooth dongle on the work PC - eventually got it connecting to the XDA2.
I have now managed to get a connection with activesync which seems to be quite robust and synchronises ok.
I am now trying to get on the internet via my active sync bluetooth connection (and tearing my hair out)
My network management is now set to a new connection I have created call 'My Work' no modem set up with the proxy settings set to those required on my work LAN. No VPN set up.
Have set the pass through on the PC to work, internet and open activesync to enable and disable but can't get ti to connect. Please help!!!!!

Going insane bluetooth activesync internet
I wish I could be so happy. Let me give a brief overview of the last 6 hours:
Installed bluetooth dongle on the work PC - eventually got it connecting to the XDA2.
I have now managed to get a connection with activesync which seems to be quite robust and synchronises ok.
I am now trying to get on the internet via my active sync bluetooth connection (and tearing my hair out)
My network management is now set to a new connection I have created call 'My Work' no modem set up with the proxy settings set to those required on my work LAN. No VPN set up.
Have set the pass through on the PC to work, internet and open activesync to enable and disable but can't get ti to connect. Please help!!!!!

maybe it's a firewall issue
try messing around with the ping program
on your pocketpc and see if you can ping the ip of your computer
and on it's gateway and dns
also make sure your dns settings on your pocketpc is set to the same as your pc
pocket ping
http://www.pocketgear.com/software_detail.asp?id=11879

Thanks for the advice. Bit stumped really:
My PC has a static IP address (10.130.16.84) I run pocket ping on the XDA and it says it's IP address is 192.168.55.101 the network is DHCP enabled. Neither of them can ping the other one (so there is no way I can connect to the proxy from my XDA2). Any ideas why my IP address isn't in our LAN range.
Just out of interest I can use a Dell X3i and connect to the network wirelessly no problem at all.

Further to baffle everyone - If i disconnect bluetooth and cradle it. I get the same Ip address but can connect to the internet no problem! So this would lead me to believe that all the connection and activesync settings are correct.

not sure here are some guides
http://www.geekzone.co.nz/content.asp?ContentId=449

Thanks for the help but the guides didn't fix the problem.
I eventually got it working (and a better bluetooth connection in the process) by downloading the slightly newer version of the XTND Blue Manager software http://www.windigosys.com/support.htm
I can now suft the internet on the XDA over activesync and syncrhonise files ok. Slightly slow but this I expect with what is basically a glorified serial port!
The only slight niggle I have now is that ActiveSync always reverts back to COM1 as the default port when I reboot my machine. Is there any way to stick it to com3?

it's blazing away at 700K/sec at least so the specs says

VPN over WiFi connection

Hi
I searched the forums for info, seems that others have had issues trying to connect a VPN session over WiFi. Basically, my wifi (internet) is connected, the 'Connect VPN' option appears in the 'Connectivity' bubble, but tapping 'connect vpn results in the unit trying for a while to connect and then giving up with no error.
Probably yet another XDA bug. My device is the XDA IIs (Blue Angel).
Anyone got a VPN going over wifi?
For the record, it (VPN) works fine over GPRS, although the implementation is shockingly bad. You cant hit boxes on yr lan via IP, it drops the VPN the moment you try. I guess i'll have to set up some hosts file to fool the sack of crap into realising that it needs to head down the VPN to get to said ip.
Nigel
Nigel

Check your ip's, they must be in different subnets at each end of the vpn eg (192.168.1.--- >>>><<<<192.168.0.---). If they are both in the the same range then packets won't be routed correctly.
I use vpn over a wifi lan every day, and it works like a dream (on an xda2 with soket wifi card).

Hi
Yeah, they are in different subnets, still refuses to connect. God knows. The wifi implementation on the Blue Angel is bugged to hell so I suspect this is just another bug.
Nigel

I can get my VPN to connect.
My M2000 is connected to my local lan via wifi (192.168.0.0) and I have set up a VPN to my work lan (172.16.0.0).
The vpn connects and shows as connected in the connection dialog bubble.
However, I can't see/ping anything on my work network.
The PPTP NDISWAN Miniport adapter shows as not connected.
Using xvIpconfig i can see that there are two active adapters.
One is my wifi card...all ok there.
The other is called RAS VPN Line 0.
It seems to have a correct IP address, subnet mask and default gateway for my work network but it says that DHCP is disabled.
Also the adapter address is 00-00-00-00-00-00...that can't be right can it ?

VPN
hi guys, have you made any progress with the vpn and the blue angel. I am having the same problem - VPN appears to connect fine and then drops without any errors etc. to make matters worse i deleted all 02 connections so now i can't even see the vpn connection. Help!!!
yanni

WiFi and GPRS

For some reason I can connect to the internet very easily through GPRS (even when roaming), but at home with my own wirelss LAN, I can connect with no problem, but each time I try to access anything on the internet, I get a pop-up stating "Could not locate remote server". I don't have a router, I am using a desktop as the gateway, I am currently accessing the net with my laptop through the same means. All configurations for the LAN appear to be correct, but I must be missing something on the JAMin. In the WiFi settings, I see the LAN, almost full signal - Ad hoc Mode - status is connected - I'm assigned an IP ... seems like everything is in order.
Will one of you wizards point out what I've missed? I know it's probably simple, usually is.

If I'm having trouble connecting a device to a network that has previously been working ok, the first that I do is turn off all network security i.e WEP, MAC address filtering etc. Then reboot the wireless access point/router and your device. If you still can't connect, you can start to blame your device.

Don't think it's a network prob...
Thanks Matterhorn, but my laptop is still connected fine, no problems there... I get the feeling that the PPC's only recognising the GPRS as a valid network for internet access... it works okay when I login to a commercial WiFi network (when I'm in the States) but for some reason on my own network here at home, it logs in, just can't find a server for some reason. The first thing I thought of was the firewall, turned it off and still no luck.
Any other ideas? I thought maybe there was a setting for default AP or connection, but can't find it, nor can I find an appropriate reference in the manual. Ugh!

Resolved!
It would seem my JAMin was trying to access the internet not through the gateway, but through my laptop. As I don't have the laptop setup to share an internet connection, it would allow my JAMin to connect, but that was all. I went in the room where my desktop is, registered on the network there and bingo!
Too simple, should have tried that right away but it didn't occur to me at the time. Thanks for the help anyway Matterhorn!

ICS & VPN with WM6

My searches on the web haven't yielded much help or information so I thought I would come to the experts...
I have a Treo 750 that I just "upgraded" to WM6 2 days ago. I noticed that DUN has gone away and was replaced by ICS. After configuring my laptop to use that instead of DUN I connected and was surfing the web. My problem now is VPN. I travel frequently (luckily I'm in the office until Jan.) and regularly used my phone to connect to the corporate network via VPN. I also work with a lot of other companies and have VPN access to their systems as well. Basically now I can open my Cisco VPN client, connect to a VPN gateway, authenticate, get assigned all the appropriate IP information, but cannot communicate on the network. What gives? Is there a solution to this? If not, what the heck was MS thinking when they did this!? My phone is basically useless for one of the major reasons I bought it...
Any help is appreciated!
thanks!

Ok, further searches found that DUN can be added back into WM6 via a cab that was posted here at the XDA forums. I installed it and the DUN service is now visible again. I unpaired by phone and laptop, re-paired, and included DUN. Now when I try to connect, I get the DUN connection box after the bluetooth connection is initiated but when I click DIAL I get the DIALING... prompt, followed by Error 678: The remote computer did not respond.
Anybody get this working on a Treo 750? Thoughts, ideas suggestions?

What is the ip address you are getting via the cisco vpn client
It maybe that it is in the same subnet as the ip address assigned to the pc from the wm6 ics. The ICS gives the address 192.168.0.1. and if your Cisco is also giving a 192.168 address then you will have two routes for the 192 address range thus giving you the problem when accessing hosts.
If this is the problem Im pretty sure you can change the address allocated via the ICS using a registry editor. If not you may be able to get work to use a different range for you on the cisco vpn.

Our corporate network is 172.x.x.x so it's nowhere near the 192.168.0.x assigned by the phone. When I look at the route in the VPN client I see 192.0.0.0, 10.0.0.0, and 172.0.0.0 so I am assuming 192 is my laptop, 10 is the phone, and 172 is the corporate network.
I'm guessing NATing is the problem. I've been reading that if I use a different APN (isp.cingular instead of wap.cingular) there is no NATing. I've tried both, and I've tried turning off and on the "force AT&T" proxy setting to no avail.
Tried the DUN cab hack that is floating around for WM6 also. The service is active again and I can also add Modem Link back in and my laptop sees my Treo as a modem but when I dial I get an error stating the remote computer did not respond. I'm guessing along with going from WM5 to WM6 AT&T also updated the radio so the old communications protocols don't work anymore?

Hello Sir,
I have exactly the same problem... I have successfully connected via VPN, however unable to communicate with any devices on that network... Then what is the use of VPN on the phone? I've tried searching online for answers, but no luck... People are having the same problem but no one knows how to solve it... I'll try and trouble shoot this problem more as soon as my exams are done...

Hi
Working successfully for me. I am using Imate jasjam wm6. Pc using cisco client connecting via ics on phone. I have telstra 3g connection tested ok on both telstra.internet (Nated ip) and telstra.extranet (real ip).
You are correct it may be an nat issue. Can you check that your transparent tunnelling is on as follows: right click on your connection entry in cisco client and select modify then transport tab. Check that enable transport tunneling is enabled ipsec over udp(Nat/pat).
The other thing to check is that the cisco vpn server aslo has transport over Nat on as well.
Also are you sure your corporate ip range is 172 or is that the range given by the cisco vpn to clients.

Transport tunneling is on (always was). I'll have to check with our network admin and check on the VPN server setting...I guess as long as I have connectivity back to the office, I don't need it that badly for all the customers I need to connect to at various times.
Yep, positive on the corporate IP. Right now it is 172.28.1.87 and I'm in the office.
Thanks for the help so far. Got any other suggestions on how I can troubleshoot further?

One other thought...should I modify the registry on the phone to assign a different IP address to my laptop? Would that help?

Same Problem
MX. I am having the exact same issue but with Securemote VPN. I've looked through the registry and found the assigned address, but I'm wary of changing anything until I can find some more information.
Anyone out there ever change the DHCP configuration for their phone?

Somewhat related question?
Im attempting to route my connection on my mobile through a laptop acting as a wan bridge, then uplinking it into the router. The issue Im having is that XP and WM6 both use the same IP Block. Ive read and read and cant find much to tell me how to change the WM6 IP BLock to something like 192.168.2.1 rather than the default 192.168.0.1
Does anyone have any pointers? Ive looked through the registry. There MUST be a simple way to change a default.
To clarify my setup, I am using ICS Via USB into a UMPC laptop running XP. The UMPC is set to share that same connection back out over Ethernet. The ethernet runs into my WAN Uplink on the router and then back out via wifi/rj-45
This setup works as I have done it using Wifi with other networks, and I can chose the "Lan3" to share under the advanced settings on the UMPC. The reason I dont just share out via Wifi from the start is that Wifi on my Kaiser and Raphael both make the device to hot to charge, thusly killing the battery within a couple hrs of sharing. If I share via USB , it stays pretty cool and still charges.
Anyone have any pointers?
I have already tried tricking XP into using the Lan on another block but as soon as you try to share the USB lan, it reverts back to the 192.168.0.1
The only way I can imagine is a registry modification or a program change in ICS.
Thanks Much!

Tethering via Bluetooth PAN, no internet on laptop

Hi all, I know this is a well-discussed issue, but for the life of me I cannot figure what's wrong here.
- Have wizard with wm6 (TNT edition)
- Have macbook pro running latest Leopard.
Want to tether between; use Edge connection on the macbook. Everything works except for one thing... the actual internet connection on the macbook <sigh>
Internet Sharing : ENABLED
Bluetooth PAN connection : CONNECTED
Device browser : Internet works
Macbook browser : No Internet
The OS X network diagnostics say that all is well (all green lights), yet no internet. Proxy is disabled on the macbook.
The only thing that stands out is that the Bluetooth PAN is always using / giving a private IP address (169.254...) and the search domain is strangely set to a network that I do not have access to before (but only then connected via wifi using DHCP); it is in a different country, yet showing up here! The search domain entry is greyed but always there (cannot delete) in the DNS entry for the connection. Never seen anything like that; not sure if it's the macbook or the device that is causing this, or even if this is the cause of no internet via PAN on the macbook.
Have read many many posts for days now and still not making heads or tails of why this failing.
Any advice, tips, hints, nudges appreciated! Want to surf via unlimited GPRS data account!

Ended up getting this to work after noticing the bluetooth PAN IP was defaulting to some wacky numbers, so did the following on the device:
- IP; entered manual IP address in the Bluetooth PAN device settings under Wifi -> Network Adapters (weird place for what is not Wifi, but it's Microsoft so no surprise).
- Submask; entered default submask (it auto fills for this)
- Router; entered the IP of the Remote-NDIS Host device (also in Network Adapters) which is apparently what the GPRS stack uses (had to go trial and error to find out).
After that, it works like a treat! Yah for unlimited data plan! But boo for dial up speed!
Hope this helps someone down the line.
case
Wizard with WM6