Database Users

Bricked my S200 after installing jasper AKU3.3 plz help!

hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!

did try upload another rom from bootloader ?

did try upload another rom from bootloader ?
but first try a hard-reset

i don't know how to load a rom from bootloader (i allready have made soft and hard reset

no one could help me ?

1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!

i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?

while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.

this rom don't work, it give me the message
error 294 invalid vendor id

it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much

pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right

stuck at boot loader -cant connect to pc

Hi,
I tried a new rom and now am stuck at the bootloader with no OS on the phone.
ipl 2.10.0001
spl 2.10.0001
gsm 02.69.21
os 4.0.0.0
I have searched all the forums and still cannot get my spvm600 to do anything. I have tried to run several roms but the problem is they cant see the phone as activesync wont connect. is there a way i can boot from the sdcard or somthing or do i have a expensive paperweight. when i try to hold down the camera and comms keys on start it asks me to format the device and then says doen and goes back to the above screen

anyone?
ideas?

Try to restart your device and deliberatly go to boot loader (keep camera button in) (keep usb disconnected).
once at boot loader screen connect usb cable ... you should now see "usb" in bottom left corner on device screen.
now run a wm5 rom like in step 1 of "how to upgrade from WM5 to WM6" thread - - http://forum.xda-developers.com/showthread.php?t=310452.
it worked for me!

every rom i try to install on it needs activesync to connect to it but activesync douesnt connect to it as the phone has been formatted. there must be a way to fix it but but i am totally stuck

Rom Upgrade doesnt need Active Sync, you just need to be in bootloader and have the usb cable connected. Then just go through the update utility.

I try that and it still seems to say no device connected would you like to try copying again. I cant understand it cause it makes that bling noise when i plug it in

Use Update_NOID
You must use the No_ID Updater to upload a ROM from the 3 colour screen. Just run this exe file and you should not have any problems.

Hi,
Please help, I too have the same problem. Installed all the versions but no use. Can any one help me how to downgrade to Original German ROM version for Neo. So that I can return to O2 company... otherwise this become expensive paper weight

thankyouthankyouthankyou
YEEAAAAHHH
my phone is now working.
the no id rom worked a treat.
xtrafletch thanks a million!!

trouble with hard spl

Im unable to upgrade the rom on my stock htc polaris.
im using vista with the 4.0 driver installed (dl'd from this forum).
I've turned off usb connection in win device center however when i try and install hard spl2 the progress screen sits at 0% and then times out with a 262 error.
does anyone have any ideas that can help me?

Use XP. I bet it works OK then...

4.0 Driver installed?
I have a stock Vista Ultimate, stock Device Center 6.1 and a German Orbit 2. It took me a while, but I finally managed it.
I didnt turn anything off, nothing. The only thing I had to change since the O2 ROM doesnt run unsigned stuff: the reg-entry to allow unsigned apps. Thats all.
Remove SD-Card
Connect to Device Center, wait till connection is fully established
Start the supplied RUU from HardSPL package
Follow instructions/click next/next/next...
Check your device, you have to confirm the execution of the loader
When the tri-color screen appears, unplug and replug, it'll upgrade the SPL and takes approx. 2 seconds
If you have no success at all: try to leave the device at the tri-color screen, quit the RUU and run it again, just leaving the device at the tri-color screen.
After a couple tries, I managed it and I'm happily running a stock HTC ROM instead of the O2 one.
Good luck, report back if it worked.

bencassie said:
Im unable to upgrade the rom on my stock htc polaris.
im using vista with the 4.0 driver installed (dl'd from this forum).
I've turned off usb connection in win device center however when i try and install hard spl2 the progress screen sits at 0% and then times out with a 262 error.
does anyone have any ideas that can help me?
Click to expand...
Click to collapse
u must be in normal status i mean just whe u r synching with vista and the ppc should be on and then start the hard spl (u don't need to go in bootloader by yourself) it will go to bootloader automatically and then upgrade will be successfull.
so
connect ppc with wmdc vista and then when connected and start hardspl

tried all of this but still no joy.
i think running it on xp would be fine but i dont have an xp box

bencassie said:
tried all of this but still no joy.
i think running it on xp would be fine but i dont have an xp box
Click to expand...
Click to collapse
failing that, go get an (micro)SD card and format it as FAT32
bung the RUU_Signed.nbh inside the rom update onto the SD card and name it POLAIMG.nbh (or to make it flash with no user confirmation, POLADIAG.nbh) slap the SD into your device and reset into SPL

Thanks A Million!!!!
Olipro said:
failing that, go get an (micro)SD card and format it as FAT32
bung the RUU_Signed.nbh inside the rom update onto the SD card and name it POLAIMG.nbh (or to make it flash with no user confirmation, POLADIAG.nbh) slap the SD into your device and reset into SPL
Click to expand...
Click to collapse
Olipro, You saved my life. After trying to flash my own cooked rom, my cruise wouldn't go beyond the splash screen. I used your tip and it worked!!!
THHHHAAAAAANKK YOUU!!!
Carlos

Newbie: cannot install Hard SPL for love nor money help!!!

Before anyone ask's I have read all the posts regarding installing the Hard SPL but still have the same problem.
When I connect through Vista 32 via WMDC it recognizes my device fine, I then follow the steps in the tutorials but as soon as I press the button to update the ROM image it goes into the 3 colour screen and then into the updating ROM progress bar were it sits at 0% for ever.
My WMDC has disconnected at this stage and then I get a screen saying communication error which is obvious as WMDC has disconnected.
Is this a WMDC issue/ Vista or am I missing something
I then have to soft reset and it just re boots into my standard ROM.
Any advice woiuld be greatly appreciated

hello
1) connect your polaris to PC
2) run update utility
3) when you see 3 color screen unplug USB and replug it immediately
4) your SPL flash may start
5) when flash end correctely your polaris reboot
6) Flash any ROM you want

Thanks for the quick reply.
Tried doing exactly as you have stated.
Unplug and reconnect in the 3 colour bar screen, after which it goes into the updating screen and sits at 0% for ages until communication error comes up.
My WMDC has disconnected and does not reconnect.
I'm at my wits end!!

Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.

Do it from MicroSD, before format it in FAT 32, after rename the file .nbh in POLAIMG.nbh e copy in your microSD, put microSD in Polaris e put it in bootloader ( photo + softreset ) you will see something like IPL, bootloader, SPLASH1, SPLASH2, gsm & OS, press POWER button and wait, it might be long,
never put off microSD, when it finishes soft reset, in the same way you can flash any ROM, always format microSD before.
I think hard-spl can not be installed with sdcard method!

Why not ??? With Trinity you can do it.

cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers

batista70 said:
Why not ??? With Trinity you can do it.
Click to expand...
Click to collapse
But this is not Trinity...Try it...
I know You can flash polaris if you use jumpspl (this is used by hard-spl flash) or hard-spl (this is used by os and radio flash).
But if you have original spl on you pda, and you want to flash with sd card, you will not use nor jumpspl neither hard-spl.

mikee5402 said:
cheers guy's for the feedback ,but not sure about the SD method unless someone can confirm it works for Orbit 2/ Cruise.
Somebody out there must have had the same issue as me regards this....what did you do to resolve.
Cheers
Click to expand...
Click to collapse
hi there.
try to hard spl with your sd card not in the device.
go in to bootloader mode (BL mode - by pressing down the Camera button, then using the stylus, press and hold the RESET button at the bottom of the phone and release when tricolor screen appears),
now connect the device to your pc (it should show usb in the white part)
flash what you may... hard spl first, oli's recomended by me.

ItayE,
Did you try the hard-spl flash with sd method? Does it work?

I didn't read it was Vista compliant so I ran it from a windows XP SP2 machine with Active Sync 4.5.
I did mine by taking out the SIM card and the SD Card then resettting and running the HardSPL.
HTH
Leon

Cheers for the advice guys I have managed to do it.
I used the Hard-SPL-V2 first which worked fine then I flashed to one of A.Serg roms, very nice and quick it is too.
However my reception bars are down to 2 from 4 that I previously had, although the reception seems ok.
Sim: O2 UK
Rom: 1.52.ASerg.4 WWE
The radio version I have is: 1.58.25.14
Now this is were I am confused.
Can I flash the radio Rom without affecting the o/s Rom, I have downloaded a couple of radio rom versions but not sure if you do it the same way as I am scared of over writing something.
Also could anybody advise if they are in UK on O2 which version gives best reception.
Any further advice much appreciated.

Dead Wizard, please help

Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.

hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps

But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?

when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.

i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08

sorry , i can't think of anything that might help you.

same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards

Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.