Hello all,
Recently, when I browsed to my SD card to grab some pictures, I saw that there was only 1 (strange) file left. So I decided todo a soft-reset, now the sd card isn't being recongized. I really want to get it working again, because I have some important data on it.
- Joe
tried using a card reader?
Or the application WM5Storage to turn your phone into a card reader?
Related
Hi,
I have a problem in recognizing my Transcend 2 GB SD-Card.
During operation the MDA Pro "looses" my storage card. I do not need to move the MDA. It also happens when it is on the table.
When I eject the card and put it in again it is recognized again.
Do you have a suggestion what this can be?
Mike
****, I just ordered the same card two days ago. Should arrive today or tomorrow. I let you know what happens.
Unless your card is faulty, try reformatting the card (I know you don't usually have to do this staight out of the box). I have had this problem before, but on the i-mate jam and it would read the card in my PC, but not my LapTop, which has a dedicated SD slot. Go figure. Tried formatting to FAT and FAT32, but I think it doesn't make too much of a difference. For me it came down to the type of SD card being used!
My 1GB Scandisk card works flawlessly and quickly wherever I put it, but my 2GB Scandisk SD Ultra II only works in my PC and transfer rate seems noticeably slower. :?
I already formatted the SD-Card. I also tried Low Level Format with
Pocket Mechanic.
I haven´t found failures with a r/w test. On the PC there are no problems.
Mike
Send it back! :evil:
Send it back! :evil:
Having 2GB MMC works fine with me... Thank God.. was worried
I have the same problem with the Transcend 2GB card. When syncing Avantgo to the card I get a "write teimeout" error. The card is still there when I look at it with the explorer.
2GB SD card
I have no problems with a 2GB Sandisk SD card.
I bought an Integral 2GB High Speed SD card. Initially, my JASJAR refused to recognise the card as anything more than 128 MB. I tried formatting it with Pocket Mechanic (Low level and normal format) - still 128MB. My notebook (with a built-in SD card reader) also saw it a 128 MB. My EPSON card reader did not recognise it at all.
After finding a post on a forum through Google, I found out that the iMate JAM apparently creates a new partition on the 2GB card, and that it was a known problem (for the JAM).
Using Partition Magic, we saw that it in fact created three partitions (128 MB, 1GB and the remainder, but we could not format or use the other).
My husband got the brilliant idea to put the card in my Nikon CoolPix, which told us that the card was not formatted. He told the camera to format it, which worked -- I can now use the card as 2GB in both my JASJAR and my laptop.
I hope this helps somebody ...
Re: 2GB SD card
paulrousseau said:
I have no problems with a 2GB Sandisk SD card.
Click to expand...
Click to collapse
Which type?
THX!
Got no probs on my scandisc ultraII card on jasjar either, but my laptop won't recognise it! :?
Good thing I have a PC too! :lol:
No problems with my UltraII card either...
I always format my cards with my PC or Laptop before using them, and it's always been fine in PPC, PC, and Laptop.
I have previously had problems with the MD drive which I've learned to live with. However now I have SD problems.
I installed WMStorage to access my SD and MD from my PC. When I deactivated it, my SD card was invisible on my Ameo. i did a soft-reset and now the 2GB SD card is only recognised as 1GB. I have tried reformatting in the Ameo and on the PC. Still it stays at 1GB.
My card is a Corsair 2GB card.
Ideas?????
I also had a corrupt mini sd card... I have a sandisk 2gb mini sd and I have copied TomTom from the original (supplied) minisd onto the 2gb card and have added a few programs and films. I was happily using TomTom in the car when it stopped working...I removed the card and reinserted (which I had done on a previous occasion and it restarted TomTom ok) This time no luck...When I got home I tried to get all my information off the card using the card reader on my laptop.... It showed the correct amount of data on the card but showed only a few TomTom files nothing else....I couldn't copy anything from the card onto the pc.... I tried to format the card in the laptop but it wouldn't format..... I put the card back into the Ameo and did a low level format using pocket mechanic ok..... Then I recopied (using the laptop) all the TomTom files again and a few programs but not any films.... So far all is good...I suspect that I had left too little space on the card, which is why it locked up!! I may be wrong here...all input welcomed
Tim
I tried low level formatting - it didn't work. Decided in the end to take the card back to the shop (as fortuntaley i didn;t byuy this one from ebay). will see if it happens again. Unlikely to be a dodgy chip, though???
Today I noticed that the 2GB SD card in my Wizard is not being detected at all. So I tried re-flashing it, and there was no change.
On the About screen, it says "Expansion slot: In use", I'm not sure if this refers to the SD card slot or not. In the Memory screen, it says that there is no SD card installed. If the backlight is off, and I put the SD card in, the backlight will suddenly turn on.
Unfortunately, I don't have a miniSD card reader to see if my computer can pick it up. But is there anything I could try to get the Wizard to read the SD card, before I go out and buy a new one?
did you figure this out? i have the same issue
miniSD card woes
Fellas,
Since one of you mentioned that you don't have an external miniSD reader for your PC, I would recommend trying out Pocket Mechanic Professional. This PPC software will diagnose/format your miniSD cards in your phone.
One very important notice...make sure that your phone doesn't go to sleep while Pocket Mechanic Pro is formatting your miniSD card. If this happens, then the only way to revive your miniSD card would be to format it using your PC...trust me, I learned the hard way.
By the way...this software is not freeware, but I believe you can use the trial for 30 days or so.
Good luck!
Here is the link:
http://classic.pocketgear.com/software_detail.asp?associateid=373&id=12178
Same Problem
I had the same problem, my 2gb sandisk would not read on my cingular 8125 OR my computer... So I called Sandisk and told them what was going on. They ask you to do a ton of different things with you computer and your phone... At the end of it all they said they would send me a new one. I was very excited because I did not register it and I did not have any of the paper work. They have a kick butt customer service hot line
Same Prob. part 2
I forgot to add once I got the new card everything worked just fine.
hi,
I've got a problem with my sd card in my prophet. the prophet can not read the sd card the card. when I use the explorer prophet doesn't show the sd card. also I can not the start the apps stored on the sd card.
When I insert the SD Card into a card reader or an other xda I can see all the data on it but not in my xda prophet. Soft reset doesn't help.
check if the card is sdhc or simply sd
sdhc cards don't work with prophet
its a 2GB SD Card from Sandisk that I use for over one year. The issue exists since last week.
it seems like it's some hardware problem
if you haven't warranty, maybe try to open your prophet and clean up pins in prophet's reader
[sorry for my english]
it seems like a hardware problem. the prophet has got warranty, so I will send it for repair.
thank you all for your support.
I have 2gb Kingstone 120x SD card. This card going very crazy... It working only in MDAII Sd slot. In pda I can format, read , write. But in many and many reader, photo, sd player is unreadable... I spent many time on conferencies but i have no idea why this card doing it. if somenone have any Idea, please reply.. I have no idea but one years back I have same kingston card (microSd) readable only in MDAII card slot... I have other PDAs but card is not readable.. only MDAII has grand master SDslot and some piece of magic.. I have no idea about this..