Hi there, I'm having problem connecting to the internet using WIFI on my Tornado smartphone (SP5m)... it always connects but takes a while to locate the url, it says "Locating..." in Internet Explorer for a long time and then finally open up the url. To me, it looks like a DNS issue?!
And that's using my own WIFI router at home with a DSL line (5 Mbits), no firewall on it, etc.
But whenever I'm connected to any other WIFI access point (e.g. coffee shops, etc), web pages and other internet stuff would load and open as quick as any WIFI laptop, any thoughts??
Thank you all for your time,
highmighty
Could it be because my personal wifi connection uses wpa encryption as oppose to no encryption at all (like in coffee shops or elsewhere)?
I wouldn't have thought it would be anything to do with the WPA encrpytion.
I sometimes get Locating... in PIE and it hangs, then eventually appears with a DNS error.
In my case it is because PIE is trying to load the page, but at the same time the device looses the connection to the Wireless AP because it's lost signal or whatever and as a result gets a DNS error.
On my end it can't be related to my device loosing the connection to the wireless AP because I'm siting next to my wireless router and the page will ALWAYS finally load up after spending couple of seconds on "Locating...". I temporarely fixed it by assigning a manual IP/subnet/gateway/dns instead of using DHCP to connect to my personnal wireless AP, now web pages are loading super fast, same as any laptop or desktop machine.
Still unsolved as to why it's doing this? Why in PIE using DHCP it stays a long time on "Locating..." while in Opera for example, and using the same DHCP settings, it loads in a jiffy?!
DNS Problem
Hello... I had the same problem and the way to solve it is assigning a DNS server to your WiFi Connection:
Start->Settings->Connections Tab->WiFi->Network Adapters Tab-> Select IEEE 802.11b/g->Name Servers Tab
And write down the following numbers:
DNS: 80.58.61.250
Alt DNS: 80.58.61.254
Leave the WINS and AltWINS empty.
Good luck!
Cheers
Related
Hi,
I tried to connect my tytn to my wifi network for the first time yesterday, and couldn't get any web pages to load.
I was connected to the router, and had an IP address assigned by DHCP, but whenever I tried to load any pages in IE, it sat at 'locating' for ages and then errored.
I thought nothing of it and thought I'd give it another try later. But since then, I get the same problem when I try to browse via activesync. The device syncs properly and is connected, but I can't load any web pages.
My first thought was a DNS problem so I've tried setting some static servers but I'm not getting anywhere. I tried 'Microsoft Network Analyzer' which gives me ticks in all the tests (even the one where it pings www.microsoft.com, when I can't browse to there).
I'm now thinking that when I'm connected via activesync it's still trying to use the wifi connection somehow (even though it's turned off). In the network adaptors, wifi is set to DHCP but has an ipv6 address in the box under static IP (odd, as my router doesnt use ipv6).
I'm pretty lost now. I could do a hard reset but I've got a feeling I'd end up in the same place when I next try to get wifi to connect at home.
Any ideas?
StarMonkee said:
Hi,
I tried to connect my tytn to my wifi network for the first time yesterday, and couldn't get any web pages to load.
I was connected to the router, and had an IP address assigned by DHCP, but whenever I tried to load any pages in IE, it sat at 'locating' for ages and then errored.
I thought nothing of it and thought I'd give it another try later. But since then, I get the same problem when I try to browse via activesync. The device syncs properly and is connected, but I can't load any web pages.
My first thought was a DNS problem so I've tried setting some static servers but I'm not getting anywhere. I tried 'Microsoft Network Analyzer' which gives me ticks in all the tests (even the one where it pings www.microsoft.com, when I can't browse to there).
I'm now thinking that when I'm connected via activesync it's still trying to use the wifi connection somehow (even though it's turned off). In the network adaptors, wifi is set to DHCP but has an ipv6 address in the box under static IP (odd, as my router doesnt use ipv6).
I'm pretty lost now. I could do a hard reset but I've got a feeling I'd end up in the same place when I next try to get wifi to connect at home.
Any ideas?
Click to expand...
Click to collapse
Check your connection settings. Some carriers have proxies enabled for your GPRS connection. If you have proxy active, you will not be able to connect through a router. AT&T does this, for example.
Yep, that was it!
My GPRS was set up under 'My Work Connection', and had a proxy server. I disabled the proxy and activesync started working.
So I completely cleared out the 'My Work Network' connection, and added a new one for my providers GPRS which made activesync work. I then set the preferred networks to Work first, then GPRS second, and everything works.
Thanks
Forgive me if this has been covered before, I'm new to the forum. I did a search but can't find a problem which is just the same - hence the new thread.
I have an XDA Orbit II and run Vista Home Premium on my desktop, connecting to the internet via a Netgear WiFi router. My desktop and my partner's are connected via ethernet to the router, my laptop connects via WiFi and all have normal internet access. The router is set up for WPA-PSK and TKIP with a long password and when I turn on WiFi the XDA connects to the router immediately, and shows a valid IP address - which can only have been assigned by the router, confirming the conection.
I seem to be able to be able to access the Internet from the XDA OK, but then another time I get "page not found" errors and cannot connect to any sites at all. Generally when this happens it stays that way and subsequent connections cannot access the Internet either. Deleting all details of the connection and starting again seems to restore the status quo, but in view of the time it takes to retype the 32 digit password, I'm not too keen to do that often!
Whilst the XDA shows as connected and shows an IP address, accessing the router setup does not show the XDA as a "connected device" - I presume it should?
I'm not overly technical, but this seems quite incongruous to me. Has anyone any suggestions as to how I should go about troubleshooting this? I've no idea if it is a problem with the XDA, Vista or the router.
Regards,
Bob
hi there , i can see that my Polaris is connected to my router via wpa2-psk
as it's MAC and ip are showed in router
I also see that an IP is assigned to my Polaris , but i cannot surf the internet
Tried IE , Opera and YouTube
Anybody has a suggestion?
depend on your network setup really
as take me my wifi dont have direct uplink
so i have to manualy set ip's and gateway and dsn to my
pda to match the computer which is the gateway and what
dns it have
you can get that in windows in a console by ipconfig /all
and manualy set my ip within the same subnet as the computer
which is gateway
Rudegar said:
depend on your network setup really
as take me my wifi dont have direct uplink
so i have to manualy set ip's and gateway and dsn to my
pda to match the computer which is the gateway and what
dns it have
you can get that in windows in a console by ipconfig /all
and manualy set my ip within the same subnet as the computer
which is gateway
Click to expand...
Click to collapse
THANKS!!!WORKS!!!!
you'd better check your router's DHCP settings as your provider might wish to change his DNS server addresses in the future and your device will keep using old, static ones
same but different?
Greetings:
this thread title describes my problem, but have to admit that I'm not certain the fix described above would apply to me (or perhaps I just didn't understand the answer??)
My setup:
HTC Advantage x7501 (freshly done a "hard reset") running WM6.
I DO NOT have a SIM card installed, nor do I plan (at this time) to use on a 3G network, just wish to use as a mini-computer on wifi. i've set the "wireless lan" Power Save Mode to "best performance" and am sitting close to wifi. Other windows and mac laptops have successfully used this router for years.
Asante FriendlyNet 3002 Wireless router (80211.b; WEP capable and on, MAC address controls capable and on)
The HTC has been connected several times to the router with the 40/64 - bit encryption. The little arrows move during connection, then stop and status is reported as "connected". The Wireless Lan "Advanced" tab shows "connected to network", reports the MAC, and the right IP address, and allows me to 'renew' it (and it always renews to the same #).
I do notice under the "configure network adapters" part of the wi-fi control settings that there are no "name servers" filled in, but the router is doing DHCP so maybe this is not a problem??? (checking my mac powerbook, I don't fill them in there either)
If I check (from another computer) the router I can see the HTC advantage shows up in the DHCP list of active clients.
Now: when I go to surf the internet, I get NOTHING with either IE or Opera 8.65.
when I put an address in the browser bar (or click a link on the Opera homepage) I see a status bar report at the bottom of the screen that says: "Images 0/0KB Looking up host..." after sometime this process times out. sometimes then I get a message to the effect of "unable to locate host" or just a time out.
Any suggestions?
ugggh: BTW, I have my "configure network adapters" setting to say that My Network Card Connects to: "the internet", not "work"
AND, under Connections I used the "select networks" button to say both types of programs should connect using "My ISP"
many thanks in advance! ( i have been trying for nearly two weeks a bit here and there, reading, googling, etc. w/o luck...)
May I suggest to enter manually the DNS and alternate DNS. I had the same problem and done that and worked.
marklar2u said:
Greetings:
this thread title describes my problem, but have to admit that I'm not certain the fix described above would apply to me (or perhaps I just didn't understand the answer??)
My setup:
HTC Advantage x7501 (freshly done a "hard reset") running WM6.
I DO NOT have a SIM card installed, nor do I plan (at this time) to use on a 3G network, just wish to use as a mini-computer on wifi. i've set the "wireless lan" Power Save Mode to "best performance" and am sitting close to wifi. Other windows and mac laptops have successfully used this router for years.
Asante FriendlyNet 3002 Wireless router (80211.b; WEP capable and on, MAC address controls capable and on)
The HTC has been connected several times to the router with the 40/64 - bit encryption. The little arrows move during connection, then stop and status is reported as "connected". The Wireless Lan "Advanced" tab shows "connected to network", reports the MAC, and the right IP address, and allows me to 'renew' it (and it always renews to the same #).
I do notice under the "configure network adapters" part of the wi-fi control settings that there are no "name servers" filled in, but the router is doing DHCP so maybe this is not a problem??? (checking my mac powerbook, I don't fill them in there either)
If I check (from another computer) the router I can see the HTC advantage shows up in the DHCP list of active clients.
Now: when I go to surf the internet, I get NOTHING with either IE or Opera 8.65.
when I put an address in the browser bar (or click a link on the Opera homepage) I see a status bar report at the bottom of the screen that says: "Images 0/0KB Looking up host..." after sometime this process times out. sometimes then I get a message to the effect of "unable to locate host" or just a time out.
Any suggestions?
ugggh: BTW, I have my "configure network adapters" setting to say that My Network Card Connects to: "the internet", not "work"
AND, under Connections I used the "select networks" button to say both types of programs should connect using "My ISP"
many thanks in advance! ( i have been trying for nearly two weeks a bit here and there, reading, googling, etc. w/o luck...)
Click to expand...
Click to collapse
I have a HTC Wizard (Cingular version). Last week, I discovered this forum and upgraded my phone from WM5 to WM6.1.... and the exact same thing happened to me! Before the upgrade (on WM5), my phone was surfing the internet thru Wifi just fine... and 30 minutes later, after the upgrade -- it didn't work.
Like you, I searched thru these forums and found various "tricks"... none of them worked for me either.
Luckily, I didn't give up on my phone. A couple days later I got the idea "let's see if I can connect to other networks". I stood out on the back porch and my phone found 3 or 4 other Wifi networks..... I tried to connect to each, with no luck. I came back into the house, and on a whim tried my own home network again --- IT WORKED! Since then, I have been able to connect to various-and-sundry Wifi networks just fine. The problem "just went away" (which some others on the forum have reported... "just keep trying", they say).
I have no conclusive evidence, but my theory is that there are some default (or residual) registry settings for Wifi that need to get "pushed out" or overwritten. By attaching to several different networks, the new/default settings in the registry gets overwritten, and once all the "bad" data is gone -- your phone will be fine.
Hope that helps.... good luck!
TY - but no success yet
MariaM:
I went to my router config page and got the DNS, then I checked the DNS from a laptop (that is successfully connecting) and both report the same:
domain net
nameserver 71.252.0.12
nameserver 71.250.0.12
Note that neither show / report a "WINS".
entering these into the SETTINGS>CONNNECTIONS>WIFI>NETWORK ADAPTERS>NAME SERVERS helped...and I did a soft reset after entering them, and the entry did hold in the setting after the soft reset.
if anyone has any ideas I'd be thrilled. Happy to do a hard reset again and start from scratch if need be. TY.
Please assist.
1. My PC identifies the HD2 as Ad-Hoc and not as Infrastructure. Is it the case?
2. The WiFi router application registers only the WAP APN in the internet connections. I usually use the Internet APN, why is it not chosen?
3. On my PC, should I enter the 10 digits WEP key for all four WEP key slots, or just into the first slot?
4. When I try to connect, the HD2 prompts me to enter a Static IP address (no DHCP support). Where should I enter it? what mask and gateway addresses?
Thanks
anyone using that app?
I tried, but I can't. Unlike the original poster, it tries to connect to my MMS access point, of course there's no internet access there. I haven't been able to figure out how to make it work yet.
Mine works perfectly but only if the HD2 is right next to the computer. For some reason the range is ridiculously minimal.
sunking101 said:
For some reason the range is ridiculously minimal.
Click to expand...
Click to collapse
Battery drain, if the range was increased it would kill the battery.
I have the same problem as the first poster : I can't choose the correct 3G connection. Only one connection is displayed in HTC Wifi Router with one single radio button on its right and it's not the right internet connection for unlimited internet.
in order to choose the right APN, please choose SETTINGS>CONNECTIONS>CONNECTIONS>ADVANCED>SELECT NETWORKS and enter the right APN (Internet) in both tabs.
That will do the trick.
still, although HD2 is discoverable by my PC (in wifi Find networks), with a good reception level, my PC insists that it is an Ad-Hoc connection (no DHCP) and when I try to use Infrastucture (with the wep key), my PC cannot establish association (get IP address from the HD2) and it shows no signal level.
Please assist.
Zolom, thanks? I did that and it improved a bit the situation: now email clients work (pop) but web surfing still doesn't work. I didn't try yet other internet connections.
not working anymore
before i installed 1.48 everything worked perfect but after the upgrade it doesnt work anymore. now my computer can connect but the phone also connects to its own network.... very strange behavior.... tried to turn off wifi but that also turns off router. any suggestions anyone?
Voila I finally got rid of the "HTTP 403 Forbidden" error with a (partial?) solution.
I have installed user agent switcher (http://chrispederick.com/work/user-agent-switcher/installed/07/) for Mozilla on Windows Vista, and I entered the user agent of my ISP on my HTC HD2 . It works!
Questions:
- Is it possible to set the user agent on other browsers such as IE or Opera?
- I noticed the user agent is not necessary for pop3 email clients. Is user agent mandatory for other internet services, like Messenger, SIP, Skype, software updates, etc?
Hello, been a long time reader from my G1 to my G2 and now my nexus 4.
I am unfortunately not able to use my device on certain wifi networks which is a real bummer.
Being that i have a background in diagnosing computer problems in my real world life, i thought i would post my findings as i found some interesting things!
First i will say that the network i will use as the demonstration is secured with WPA2 PSK AES security and encryption.
I can connect to it and often find i have problems on the first connect to the network. By this i mean if i have made my wifi settings 'forget the network' and then try to connect again.
On the first time it seems to indefinitely hang, showing the message 'authenticating' on screen next to the network and if i long press on the network name and press modify, the dialog shows that i have a link speed of 1mbps.
I can usually get past this by turning wifi off and on and then reconnecting, at which point it will connect straight away and have a normal link speed. (in this example 72mbps).
After i am connected, i find that the following does not load:
-browsing webpages through chrome does not load
-the wifi icon turns grey
-play store cannot load anything
I find that i get assigned an ip address by dhcp correctly too with the right gateway and dns.
I decided to download a network tool to have a better look. I use fing personally.
I found it very interesting what i found, which no other threads about wifi issues mention.
Network discovery found every device on the local wifi network.
I was able to scan the services of my computer which is also on the network and it found everything, including a http server which i run which i could browse to.
In fact i could do everything through wifi with this device and most others.
Again it got interesting when I then took a look at my gateway, the router.
I had discovered its mac address which i can verify through my computer is correct which to my understanding, being that i can communicate through the wifi, means that i have the information available to send information to that physical device?
When trying to scan services, i find nothing, which is not true, at the very least it exposes a http server on port 80 which my computer can access.
When trying to ping i have 100% packet loss.
So at this point it is only the gateway i cannot access.
So i figure i could setup another computer which is connected to the network with a wire to share its connection through wifi onto that network and then i have a standin gateway?
I connected this computer through wifi to the network and pinged it succesfully with my phone. I then turn ICS on my wired adaptor to share to my wifi adaptor. I ensure that the wifi maintains an ip address in the right range and subnet.
I then try to ping that ip with the phone and it then gets 100% packet loss.
Could this be that when a device is configured to act as a gateway something changes about how it handles any packets sent to it that the nexus 4 is currently in compatible with?
elltg said:
So at this point it is only the gateway i cannot access.
So i figure i could setup another computer which is connected to the network with a wire to share its connection through wifi onto that network and then i have a standin gateway?
I connected this computer through wifi to the network and pinged it succesfully with my phone. I then turn ICS on my wired adaptor to share to my wifi adaptor. I ensure that the wifi maintains an ip address in the right range and subnet.
I then try to ping that ip with the phone and it then gets 100% packet loss.
Could this be that when a device is configured to act as a gateway something changes about how it handles any packets sent to it that the nexus 4 is currently in compatible with?
Click to expand...
Click to collapse
I have found a bit of a workaround that i can use!
When i said i turned on the wifi and ICS i did the following:
-Turned on wifi.
-Connected to wifi network.
-Turned on ICS on my wired network to share to my wifi
-Observed that my ip changed from 192.168.10.x to 192.168.137.1 with no gateway or dns.
-I decided to change my ip on the wireless to 192.168.10.x and gateway to my router 192.168.10.10
-I then tested.
I ran through this again but slightly different:
-Turned on wifi.
-Connected to wifi network.
-Turned on ICS on my wired network to share to my wifi
-Observed that my ip changed from 192.168.10.x to 192.168.137.1 with no gateway or dns.
-I decided to change my ip on the phone to 192.168.137.5 with gateway and dns as 192.168.137.1
-I then tested. And it works!
I know this doesnt fix the wifi issue itself, but for me, this makes a big difference as i can now use wifi at work where we also have poor mobile network coverage.
Edit:
Additionally i previously tried to setup this same computer to host a wifi network to share the connection using 'netsh' and creating a 'hostednetwork' but i found i was in the same situation where i still couldnt get the internet.