Hi,
I am writing because I have some problem with my Qtek S200.
I have downoladed on this site a new ROM wm6pdamobile, I have installed it, and now my pda is blocked on a white screen.
When it starts appears the normal HTC page, the check of OS, GSM etc., and then.... nothing... only a white screen.
What I can do?
How I can format my pda? It doesn't works with active sync, because it can't take a valid IP, and so I can't reinstall a precedent ROM version.
Please help Me!!!!
Thanks
It is important to hard-reset your device after upgrading. Have you done hard reset? If not do it.
mine oso
i have installed WM6
i had hard reset..
but.. it goes to Align Screen
and stuck !!!
looool, u must reinstall a new rom.. dont ask me how..
Related
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
please help! I have made a wrong ROM Update for my Artemis. The result is that it doeasn`t starts anymore. I see only the start screen no more. If i make a SW or HW reset tahn i see a 3 colored screen and USB. But i don`t get a connection via usb to my compute`! How can i wake up my Artemis ???
tell use more what did you do and how did you do it?
what artemis is it?
what rom was it
Flash went sour..
You need the original ROM which was on your device when you bought it. What version (HTC, MDA, etc..) and what language was the original ROM?
please i need help too
I guess I made the same or a similar mistake that dr.moppi did. My machine is a Dopod P800 from mainland china with the chinese operating system. I flahsed it with PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap. Don't really remember what the original ROM was but now when i turn it on it freezes when it lights up. On the screen, it says
IPL 1.27.0001
SPL 1.27.0000
GSM 02.67.90
OS 1.28.0.0
DOPOD
I don't get a connection through usb to the computer either. I am not sure if I did the hard reset correctly. Didn't understand the instruction on that "press the soft key left and right and soft reset at the same time." Anyway, you guys are all experts, can you help me please?
it should be the same as my problem
if i remeber than i used the same ROM Update :-(
I hope anyone could give us a solution, please.
@dr. moppi we can only help you if we know what version you had before.
@empathyvirus you have to look for the original ROM which, in your case, should be the Chinese Dopod ROM. Install that one and your good to go.
Without the original ROM the only thing left to do is: sending your device to your provider or contact and sent it to the guys of imei-check. Either way, you'll probably have to pay to get it fixed.
how to install original rom
Thanks for your quick reply Pyth. In the case I get the original ROM from somewhere, how do I install it if I can't get a connection between the phone and my computer? Can you advice?
Put your device in bootloader by pressing the record button and reset at the same time. If you have your USB-cable connected between your PC and your phone it will indicate a connection by 'USB' in the left corner of your device. Now you should be able to run the ROM executable and update your device.
thanks anyway
i tried but it didn't seem to work. anyway, i have troubled you enough and maybe it's best i just go to the repair centre of dopod and pay for a fix. i really appreciate your help though Pyth.
Where can i find the t-mobile rom its the MDA Compact III that wont start for me
I have serious problem with my PDA SPV M2000 after upgrade to WM6. After upgrade i try to restart my PDA with Hard Reset, but can see only 4 collored screen. I can acess only bootloader mode and nothing else... PLEASE HELP
reflash
Did you try a reflash?
I try all the steps 5 times but nothing. I try use WM6 from helmi and xpode. With the same resolution. Now i try to downgrade to WM2003...
I am back on WM2003. Thanx god
I got a gray screen whith serial v 2.07... and few pages i find dosent help me att all..... please help me some one....
brb66 said:
I got a gray screen whith serial v 2.07... and few pages i find dosent help me att all..... please help me some one....
Click to expand...
Click to collapse
the grey screen with serial v 2.07 is the bootloader mode...
maybe a reflash will do the trick...
how did you screw up the upgrading process? did you accidentally unpluged the cable? is it a corrupted file?
I have never experienced this, but, if i were you, I would reflash it. if nothing good come up,then maybe the file you are using to upgrade is corrupted...
hope this helps, and maybe the experts would have more ideas cause i am just a user.....
I've upgrade to WM6.0 pdaviet, but can't use GSM network : no services...
Any body help me plz...
fix it now, pdaviet'rom works well with 1.15.00 radio .
sorry for my English
Ibhave a tmobil MDA amd i did an upgrade to windows mobile 6 and now my MDA is slow in most of the programs also the SMS when inserting any messages the words do not show after at least 10 sec.
Please, definelly need help.
navarde
Have you performed HARD RESET?
What ROM did you use for flashing?
(also some installed programs may slow down your device a lot!)
I had the same problem. From time to time whem im flashing my phone its happening. After few soft resets it'll be ok.
my sp3i is stuck on the WM splashscreen and afther that it just turn off, i'v installed WM5 and then back to the original WM2003SE from imate but after a while it just begun to do that, plz help me.
does any one know how to make a reflashing throw SD? can anyone make a guide? plz helpme to revive my dear phone.
thanks in advance.
Your phone can be reflashed with Mtty even when it freeze on the boot screen cause its not necesary have the phone ON.
Tried to do a hard reset maybe is a windows registry problem.. after the hard reset the values on registry will be reset to default.
already done that, and doesnt work, even it reflashes through USB but afther reaching 100% the phone restarts and get stuck again in the same place, no matter if I hard Reset or reflash by USB the phone still get freeze.
can any one tell me how to delete all the data on the memory to make a clean reflash? or how do I reupload the firmware? is there a way to recover the phone?
remember I already install the WM5 and back to WM2003SE but after that the problem started, maybe i screw someting wile doing it?
Solaris_irc said:
my sp3i is stuck on the WM splashscreen and afther that it just turn off, i'v installed WM5 and then back to the original WM2003SE from imate but after a while it just begun to do that, plz help me.
does any one know how to make a reflashing throw SD? can anyone make a guide? plz helpme to revive my dear phone.
thanks in advance.
Click to expand...
Click to collapse
Tutorial for sd flash
Check here
hi my friends.
I changed my jasjar's tomal 6.1 rom to Original WM5 for sell my phone
but after changing rom, i have a terrible problem.
when i closed the battery for change the simcard and turn it on. when the windows logo appears a blue screen showed and the gsm led begin to work (blinker).
after several soft resets the windows starts and ready to work but when i press the power button to standby the device (sometimes) for turn on the device (after standby) the screen didn't appear.!!
i'm very upset
after that i flashing the radio to newer version (1.18) and flash back to WM6.1 TOmal , WM6 , ... but i still have this problem.
in the tomal's wm6.1 rom (TML_v82_WM61_19960) before the problem shown an error appears under the windows logo > The Skin Is Not Loaded < and after that a black or blue screen appears and nothing...
please help me to fix it.
thanks friends
No Answer ?!
Really ?!
it's very important for me.
plz help
Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.
-Jonny- said:
Only thing I can think of is to doc-format (mtty). And then flash ROM again. Then make sure you Hard Reset.
Click to expand...
Click to collapse
What is the mtty ? doc-format ?
How can i do it ?
tnx for attention
DOC format
-Jonny- said:
DOC format
Click to expand...
Click to collapse
wow , thanks for guide me.
as your experiences , this work would be harmful for the device ?
thankx
It's not harmful - basically it totally wipes the device removing everything (including garbage). So you will, of course, need to flash a ROM afterwards.