Can't turn on phone while charging - 8525, TyTN, MDA Vario II, JasJam General

i can't turn on my phone while it is charging throught usb and normal power. the red light is on but i just can't turn it on. anyone can help me with this? thanksXD

Did you run the battery all the way down?
Red light means charge is below acceptable level.

Yep red light means battery is below the level where it can power the device and it has to charge so that's is why it won't turn on. Just give it a good charge and it will be as good as new hopefully.

even when i plug it in with 50% it'll still be red light. is there something wrong?

I was having the same issue with a cingular branded 8525. hard reset didnt work..flashing the rom didnt work. at&t sent me a new one a few days ago for free.. just talk to their warranty exchange and tell them htc deemed the device defective.
...(then install wm6)

ya, i bought mine in HK so exchanging it is out of the question, anyone else have ideas?

This has been a problem that has affected a small number of Windows Mobile phones all along. This is not specific to the Hermes or any other WM PDA phone.
If you can't exchange it, and you've tried the basic things like a hard reset and flashing the ROM, then you'll just have to live with it.
(You do know that you should first try a hard reset for every problem like this, right?)

Related

XDA 2 Say Always Charging

http://forum.xda-developers.com/viewtopic.php?t=8348&highlight=always+charging
I have a same problem before. But im update my device rom to 1.72.00 (Imate Rom) (Before my device have a 1.72.00 T-Mobile Rom) that problem is gone until my charge going %15. After that not blinkin Orange light is coming (thats normal for charge is about 10-15% but) also Setting > Power say charging and My XDA think its charging. Im not plug in my device anywhere (Cradle, Power Charge, USB Sync) but its always thing charging and charge is faster dropping to zero.
I dont understand anythig about that. After that i plug in my USB sync in my notebook and recharge it. After my battery full (100%) im unplug the sync cable from my device and nothing change. Its still say charging
After this i decided (i dont know why i think about that. please dont ask ) i plug in USB sync cable and plug out on my PC (Cable still plugged in on my XDA 2) and device gone normal. And unplug sync cable from my device. Orange light is gone and Settings > Power say Battery Mode.
Is there anythig wrong that. I think this is totaly software error bu i dont know.
Thank you for your advice.
My case was different. No matter what I did, the device ALWAYS thought it was in charging mode. I sent it to the repair centre twice and the device gone back to the problem again after a while. They said the connector pin has been in short circuit and so it thought it was charging. They also accused me of damaging it. I asked them why it would be so when I use it normally, the staff said 'Machine is like that, nobody can gurantee'. I was angry and sent several rude mails to O2. Upon some negotiation, they changed a completely brand new model to me and the problem did not happen anymore. I have used this new one for several months in exactly the same way I did with the old one and nothing untoward happen. That proved the old one was not damaged by me!
Sorry for being long-winded and yet could not solve your problem.
Anyone can help?
My device still have a that problem.
Im looking lights now and its some time say charging and some times not.
Please help
Thank you
always charging
i still have same problem :!:
anyone? help?
omg, this is exactly what my problem is. My XDAII always thinks that it is charging even though it is not plugged to the charger nor the usb sync cradle. And the amber LED light is steadily lighted like when you are charging, battery life of the XDA has dramatically gone down, it wont last me 3 hours or so and yet it is still on standby mode. I had reflashed it with the latest ROm available, 2.06WWE i think, and still after that, after the cold reboot, the problem was still there. Anyone has a better solution to that? Im planning on returning my unit for servicing if the problem cant be solved.
i have same problem , help me now
This will be less likely to happen when using usb cable rather than cradle. If you get a magifying glass you may be able to see the short on the pins and possibly nudge it back into position with a very thin sewing needle or similar.
up
i have exactly this problem too (
I´ve the same problem since yesterday with my T-Mobile MDA², it´s Rom Version: 1.72.01GER (6 months in use without problems), Rom Date 03/16/04, Radio 1.17.00, Protocol 1337.28, ExtRom 1.72.170
The yellow light is always on and the batterie runs very fast out of energy (1-2 hours) and it´s always says charging and think it´s connected to AC power...
any fix to this problem?
or what happen now to those who have this problem?
I have this problems too!!! How to fix it?

very dead exec

Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
towinguk said:
Having not use my exec for a bout a month I now find it will not start or take a charge (battery has 3.8v ) but it will not power up ,it is still in warranty BUT I have changed the rom ,so don’t know if o2 will repair it
If I use the wall charger a LED flashes on for about 1 second ,if I plug in to usb lead on pc (with battery removed) red led comes on any ideas appreciated
Click to expand...
Click to collapse
Problem indeed.... Firstly, I wish I could offer some constructive solutions, but afraid not.... it does sound like a worn battery, and maybe worth trying (or borrowing) another one to flash?
I take it as you refer to it as an 'Exec' that it is the O2 branded one? If it is, from my experience with the O2 technical support, they really don't have a clue. I would assume that they would send an exec straight to HTC for testing. It's a complete last resort, but if you were to tell them that your unit was dead and they were to take it in, they wouldn't be able to solve the problem before they sent it back to HTC. This is of course after you have clarified it's not just a dead battery cell.
Best of luck with the thread and hoping someone a bit more experienced can help.
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery remo....
good luck
Click to expand...
Click to collapse
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
kecido said:
So, let me get this straight, your universal does not turn on (and by turn on I mean that you see the familiar wm5 screen with your apps, etc.), no matter what have you done, and the only way to have the charging led on is by connecting it to USB port with the battery removed?
If this is the case, you might have a dead internal battery charging/power supply circuit, i have repaired some old Ipaqs with this failure, most of them failed due to a defective battery, easily recognized by overheating when the unit was placed in charge, usually the overheating increased slowly in time (months usually).
I don't want to be misunderstood, but all these devices have a way of turning of the LCD backlight, a long pressure on the on button does this, it can restores with the same long pressure, see if this is not your case.
If you have some electrical problem with your PDA you might take it to repair or you could try to do it yourself -if you're able to do it obviously-.
Anyway, try to get yourself another battery (you might ask for it to someone else with a uni), put it on and see.
I'm also assuming that you have tried to hard reset your device.
good luck
Click to expand...
Click to collapse
thanks for all the help
1 it will not turn or power ,no led no screen
2 battery dose get hot when charging
3 screen has not been dimmed
its back at o2 shop now we will see if they repair it and ill report back !!!!!!!!!
Grilloman said:
Look maybe this will give you some hope. Yesterday I took my Htc Typhon (smartphone) after a long time, the battery was die. I tried to charge via usb, and nothings happened, then I tried to use a usb charger and nothing happened neither. Finally I charged the battery alone on an universal battery charger and after 30 minutes my phone was alive again.
Hope it will help you!
Felipe
Click to expand...
Click to collapse
hi thanks for the reply i have had the same on a m600 ,would not charge from usb or car kit but did start with mains charger
i have tryed hard reset but it will not do that either
battery is stuck at 3.7v even after trying to discharge it with a small bulb
thanks
John...
This is something I've had happen in the past.
Try taking the battery out, and put it into a ziplock back, and place it in the freezer for a few hours. I know, I know, it sounds ridiculous. But sometimes, just sometimes, it will reactivate the cells, and you'll be able to charge it after that.
well done o2 uk
well as said before took my phone back to the O2 shop and sent it off to the service centre. The report came back that the main board US .not only did i get a new exec but But a new boxed one and a full set of all original parts !!
i had this problem when i first got my SPV m5000..i took it to the orange shop...(the people where nice) they kept it for few testing and said...
battary was faulty...so they gave me a new battery XD

Athena dead or dying........any miracle workers out there?

Background:
I have had MANY PPC's (so many I can't even count them) and I've loaded many different cooked ROMS and such on most of them so I'm not a complete noob on these things (don't claim to be an expert either).
However, my most recent acquisition is an HTC Advantage bought at CompUSA. I've read most of these came with a test ROM and mine was no different except for the fact that when I attempted to update the ROM to the "official" one provided to me by HTC it would not work. I always got the error "Connection lost" about half way through the process. I tried it numerous times and it never worked. On some occasions it would get stuck on the bootloader screen but I was able to get it back to working status (still on the test ROM).
I decided to try installing step 1 of Ollipro's SPL to see if that would help loading the HTC ROM. Turns out that wouldn't work either. It would get stuck at step 1 where it would ask if "PPC gone idle and didn't work or to wait 30 seconds". Tried it many times and would try to get it to keep going but the grey box on the bottom left would say the "parameters were incorrect" and would give me the option to quit, which I would. No problem, at least my 7501 was still working.
After that I tried the official HTC ROM again and I got the same "connection lost" error I had previously, except this time I didn't get anything on my PPC screen, just a black screen, not even the battery charging light behind the joystick lights up anymore. Soft reset...........nothing. Bootloader reset....................nothing. Hard reset.......................nothing. No lights, nada. The only flicker I get is if I try a reset wheen the power cord is connected. A red light flickers behind the joystick whenever I click the reset button. Any ideas or any help?
Sounds to me like the battery is just dead. I bought one at CompUSA (had the test ROM also) and I got the red ring around the joystick too when I tried to turn it on in the store. I left it plugged in awhile and it finally booted up okay. I then replaced the test ROM with the one and only available for the X7501 on HTC USA's web site. Good luck and I hope you get it working!
I think it could be battery related as well but it had a full charge when this happened. For some reason the unit has lost communication with the battery. I'm at a loss.
I got the same problem like you man !!! but i bad luck and so stupid man , i did with HTC X7501 then it dead after that i bought the X7500 then did it again , holy "... " it dead again....man ...So how your phone now bro ????
I left out the battery a half day and tried it again but still dead. Then I left it charging overnight and tried it again but still dead.
I can't believe this. I've never had a bricked device that can't be revived but after so many have seen this post and still no solutions I'm guessing it's no hope.
I met the same situation when I started to unlock Athena ( TMobile Ameo) within not fully charged battery ( less then 70%).
Solution ( try to make BL mode) with connected wallsocket charger ( not connected to PC USB slot) or find 100% charged battery. It helped me two times.
After many tries it changed to BL mode .
Now I didn't start unlock/change ROM without 100% charged battery.
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Lobstrick said:
I have the same BIG Problem, only red fliker when soft reset when AC conected. I wanted to update rom from russian to english and phone stoped working (black screen), and battery heats when inserted in phone . nothing to do? i read everything but i have not got any solution. I think it may be bios dead. helap us please
Click to expand...
Click to collapse
"heating battery" (i.e. discharging when inserted, you mean?), no charge led = dead bootloader indeed.
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Hearing these stories makes me nervous. I'm on the stock ROM (mine came from CompUSA with the latest ROM and I don't have an urge to try the cooked ROM yet). I've been using my Athena daily for 4 months, it charges correctly from several different chargers I have (car, computer USB, stock wall charger, aftermarket wall charger).
However, one day 2 weeks ago I went to make a call in the middle of the day and my Athena was dead. D-e-a-d. Usually I can make it back home at night and still have 90-100% on the battery meter, so with no use in the middle of the day and a dead battery, this was weird. It wouldn't turn on, no soft boot, took the battery out and put it back in, and always got nothing.
I bring this up here because when I plugged it in, I encountered similar problems that others here are describing. It wouldn't turn on, and it didn't give me the orange charging light behind the joystick. I ended up leaving it plugged in for a while and finally I got a red ring, not the usual orange. I've only seen red when the battery was almost dead and the unit was on. Then after some more time the ring turned orange and at this point it would turn on again. I still have no idea why my battery died so fast and hard.
So, is there a problem with the battery charging system that is starting to crop up in units that have been used a while???
miha_conan said:
I get the same problem. My device is work, but not charge. Also like yours i have red ring around the joystick when the battery is taked out. And if battery inside, when i make a softreset it blink one time, continued to load but not charge.
You`r speaking all wonderful. But have anybody found the solution?
Click to expand...
Click to collapse
Hi i am no expert but i had simaler problem no display or no lights round ring no responce to any commands (ie hard reset and bootloader ) only red light flickred on reset button all i did was removed battery while pressing reset button and placed new battery and left it on wall charger for couple of hours and before doing hard reset i pressed reset button 2 to 3 times and green light round the battery came up so i tryed bootloader and it worked and insted of flashing it with pc i just loaded the img in sd card and flashed it while whole thing was on charge (i had tmob test rom before ) which i think is best way to do no hassle of losing connection or failing in half way and it works like a charm
hope this helps
and ya if you have a spare battery it dose help
New battery?
I'm a wizard user (and lots of former PDAs) looking to buy and Athena, maybe.
Has anyone tried a new, right out of the envelope, battery? these issues sound like worn out Li-Ion batteries to me. I've had them completely conk (won't take a charge at all) if I let them go completely down, and I've had them wear out and stop taking a full charge (down to maxing out at about %20, but sometimes showing %100 depending on ROM status) when I kept charging them while they're already charged.
Li-Ion batts don't sit for long periods too well, either, so if they're sitting on the shelf at the store/warehouse, they may be suffering even more than one that has been used since earlier in its childhood.
Perhaps the answer is a switched charger that stops charging when the battery (not the ROM/unit reading) gets to %100. ???
I didn't see anything like this posted. I'm terribly curious to see if anyone can resolve it.
nother AMEO dead
http://forum.xda-developers.com/showthread.php?p=1859021#post1859021
Red ring comes for a sec only try to RESET the device with Charger connected
Click to expand...
Click to collapse
same here,
i am afraid i got a dead athena too, did you guys found any solution?? i tried switching batteries. this is my first experience with a windows mobile device not powering on, in inrepairable condition.
found another member with similar problems- http://forum.xda-developers.com/showpost.php?p=1639311&postcount=24
No genius,s on here,just insults
i have read every page on the advantage x7500,being such an old phone you would thin the genius,s on here could sort it out in seconds,but all they do is insult you.i tried to update from windows 6 on radio 1.20 to michys radio 6.5
it got to 94 percent then crashed, now when i boot up i just get a black and white screen,which then turns white,if it try to reinstall advantage 6.0 the phone reets after 2 or 3 percent..will anyboby help by giving simple term advice to unbrick it? NO.will they provide links to there advice no.THEY JUST INSULT YOU AND SAY ITS IN ONE OF THE THREADS.well im a computer tech and if anybody wants there pc or laptop fixing.guess what i will return the favour with computer speak,THAT YOU CANT UNDERSTAND

Amber charge light always on! Arrhh!

Hi everyone,
I have an unusual problem and I have searched almost the whole internet but I have not found an answer, so now I turn to you for any ideas. My problem is that over the past month, my amber/orange charge light remains constantly on, even when the phone is not charging. I have tried to soft reset, I have looked into HKLM->Drivers->BuiltIn->Battery key and have found no solution. The phone will still charge the battery OK. The other bluetooth light works OK, it still blinks when bluetooth is on. The right led remains orange. I have also tried to take out the battery and re-insert, but issue persists. I am using Faria's 3.3 and IPL/SPL is 2.26, radio is 2.61.11 for over 6 months on a WIZA100, but the issue has occurred a little over a month. Phone has always been well taken care of, no major drops and absolutely no water has ever touched it. Battery drain is normal, I get about 1 day and a half of normal usage, push email. I thought it was batterystatus, and I have removed it, but problem persists. When I soft reset, as soon as the IPL/SPL screen comes on, better yet, as soon as the HTC logo screen before the IPL/SPL screen comes on, the battery light remains constant orange. Any ideas? Please help!!
Sincerely,
Ricardo Cheing
Ricardo Cheing said:
Hi everyone,
I have an unusual problem and I have searched almost the whole internet but I have not found an answer, so now I turn to you for any ideas. My problem is that over the past month, my amber/orange charge light remains constantly on, even when the phone is not charging. I have tried to soft reset, I have looked into HKLM->Drivers->BuiltIn->Battery key and have found no solution. The phone will still charge the battery OK. The other bluetooth light works OK, it still blinks when bluetooth is on. The right led remains orange. I have also tried to take out the battery and re-insert, but issue persists. I am using Faria's 3.3 and IPL/SPL is 2.26, radio is 2.61.11 for over 6 months on a WIZA100, but the issue has occurred a little over a month. Phone has always been well taken care of, no major drops and absolutely no water has ever touched it. Battery drain is normal, I get about 1 day and a half of normal usage, push email. I thought it was batterystatus, and I have removed it, but problem persists. When I soft reset, as soon as the IPL/SPL screen comes on, better yet, as soon as the HTC logo screen before the IPL/SPL screen comes on, the battery light remains constant orange. Any ideas? Please help!!
Sincerely,
Ricardo Cheing
Click to expand...
Click to collapse
It doesn't sound like you've tried hard resetting your device yet. Hard resetting the device will not revert back to manufacturers rom but will bring you back to the part where you configure the phone, before customization.
I imagine this is the only way you are going to get the orange light to go away, at least when its not charging... You can hard reset by holding the comm manager and voice button and pressing the reset button with the stylus.
BACK UP EVERYTHING BEFORE HARD RESETTING!!!! If you do not, you will lose everything on the device IE: music, videos, pictures, documents etc...
Try to use another Radio ROM version. The charging related issues are related to the Radio ROM.
Thanks guys, I will change the radio rom on my phone before hard resetting. I didn't want to try to hard reset because of the way I already have my phone configured. I have heard there is a way to create a cab with all customizations, but I'll have to figure out how to do this. I will report more later, because I'm at work right now and I don't have the usb cable.
Ricardo Cheing said:
Thanks guys, I will change the radio rom on my phone before hard resetting. I didn't want to try to hard reset because of the way I already have my phone configured. I have heard there is a way to create a cab with all customizations, but I'll have to figure out how to do this. I will report more later, because I'm at work right now and I don't have the usb cable.
Click to expand...
Click to collapse
Hi, my phone last night (O2 XDA Mini S (Wizard)) started the exact same symptoms as you. At half 4 last night the screen came on and the phone claimed to be charging, while unplugged. I soft reset, but no change. by the morning the phone now claims to be fully charged. I've taken the battery out for a while, soft reset but nothing has worked so far, it now claims to be 100% charged constatnly, so i'm currently running the battery down to see what happens.
did you ever find a solution to this?
Hello, just wanted to update the thread, after 1-2 months of the battery charging light always on, no matter what, it fixed all by itself as I was preparing to hard reset my phone, no BS, I swear. I took the phone in my hand and was debating if I should hard reset or just flash another radio rom, and bam, I saw the light go back to normal, blinking green. That day it went back to always on, but then it would fix itself, but finally it's back to normal. So I went ahead and flashed the official T-MO 2.26/ 2.26.11 ROM which downgraded my Radio from 2.61 back to 2.26.11 and replaced my OS and then I flashed the official T-MO 3.08/ 2.69.11 ROM which upgraded my IPL/SPL and Radio. I then flashed Dr. Dot's BlackDiamond 2.0 WM6 and applied the 2.69.11 radio fix on XDA Mobile 6 Release 3. My phone has been wonderful since, thanks everyone.
hi leewebster try this and let me know if it works for you
thanks Ricardo Cheing ,
your input helped as this problem started when i had charged my phone with wife's dopod m700 charger
any way after playing around for some time i figured a workaround for it
i did the regitry hack for disabling the charging via the usb,
powered off the device by pressing the power button then took out the battery and put it back and then powered the device and the problem was sorted also the phone now will not charge when connected to the comp
now if i enable the charging via the usb then the problem returns
hope this is of help to somebody
ps: registry for disabling charging via usb
HKEY_LOCAL_MACHINE/DRIVERS/BUILTIN/usbfndrv
enablineUsbcharging change the value to "0" (for disabling)
and
"1" (for re enabling)
Thanks for this tip, I have added a reference to this thread in the Wizard Wiki
just to update
today i re enabled the charging via the usb by making the registry hack , powered down the phone took out the battery and then restarted the device and was pleasently surprised to see that the device no longer had the solid amber light
device is working absolutely fine
Sweet hack
Hi, The post about disabling USB charging does indeed cure the charge light on all the time. Now the battery status works correctly. Only drawback was I use a cradle to charge with a USB plugged into a wall adapter. It won't work because of the USB being disabled and I mistakenly assumed since it was plugged into the wall it would although USB is USB whether powered from wall or computer. The factory AC adapter charges it fine though and the annoying light on all the time is gone. SWEET!! I will also re-enable it just to see if it remains gone like you did after a few days, and hopefully it will. If it doesn't I can live with it the way it is now
Thanks for the post!
Amber Charge Light Always ON!
wizard1 said:
Hi, The post about disabling USB charging does indeed cure the charge light on all the time. Now the battery status works correctly. Only drawback was I use a cradle to charge with a USB plugged into a wall adapter. It won't work because of the USB being disabled and I mistakenly assumed since it was plugged into the wall it would although USB is USB whether powered from wall or computer. The factory AC adapter charges it fine though and the annoying light on all the time is gone. SWEET!! I will also re-enable it just to see if it remains gone like you did after a few days, and hopefully it will. If it doesn't I can live with it the way it is now
Thanks for the post!
Click to expand...
Click to collapse
Dear All,
Please help me if possible. I have been facing this same issue, however, when I go to battery icon and click on it, the next screen shows that the battery bar is running as it runs during charging, though the device is not connected neither with USB and/or wall charger, amber light is also stays on. I did hard reset, i did soft reset, I took the battery out and put it back in, all my efforts are in vain, no success sofar. I must tell everyone here that this is my third battery and the last two faced the same problem and then died and now they are useless, using those two batteries, i can't turn the device on, i cannot charge the device, they are garbage now, please help if possible!
Is There any solution to this....
hi I have been facing the same problem in my HTC touch Viva (India))...... but the problem is random .......... all of a sudden the light comes on and the phone claims to be charging without any source of charging ............... however in my case soft reset makes the light revert back to normal......but the problem re occurs after a few hours ....... I have tried every solution given on the internet (Hard Reset , registry hack etc) ....... but no avail.........Has anyone found a solution to this
My phone Specifications
WM 6.1
ROM 1.35.720.2 WWE
RADIO 03.37.90

Phone will not turn on... HTC TyTN

I have the HTC Tytn and it will not turn on. It was sitting on my desk one day with more than 50% charge and when I picked it up to make a phone call I noticed it was turned off. I tryed hitting the power button to turn it back on, but nothing happened. I have removed the battery and tried just about everything I could think of. Even when I plug the unit into the wall charger there are no indicator lights. I read on some threads that my battery may not have enough charge to begin charging (I know that makes little sense, but it is true) so I took the battery out and tested the voltage. It rated at 4.17 Volts which is higher then the 3.7 rating on the battery. This means the "jumpstart" or extra "kick" that would normally be suggested would not work for me since I have too much charge. I have begun discharging my battery and it is down to 3.99 Volts, but I don't really know if this would help anything.
If anyone has had a similar problem and has a solution I would really like to try it, I am willing to try anything at this point. I know I am new to this forum and this is my first post, but I discovered this site through Google and found it to be full of many interesting posts. If any of these solutions work I would be happy to make a donation to this site. I appreciate any and all help.
-TOM
Hi Flashrapid,
Have you tried a soft or hard reset? If the phone comes back on with either of these solutions then let me know as there is more to be done to stop this happening again in the future.
Feel free to PM me directly if it helps.
WB
Same problem here. I know this is an old thread, but Im having the same exact issue. Completly stock factory ROM very few 3rd party add ons never dropped.Phone was actually a 3 month old refurb that I had replaced another 8525 with under warantee. No charging lights or anything. Tried soft reset,not sure how to hard reset with the phone dead. Anyway if someone has any insight to this issue it would be greatly appreciated. Thanks in advance.
Hard reset as you normally would - 2 softkeys and stylus reset.
Does the red LED come on when you connect to the power without the battery?
The Hermes should, if there is no hardware problems, show a red light to indicate no battery when you plug it in without one.
Cheers...

Categories

Resources