ATOM EXEC - White Screen - iPAQ rw6828, XDA Atom General

Hi,
My Atom-Exec decide over the weekend to go to a white screen and display nothing. i can hear things going on in the background (i.e beeps etc) but cant see anything. it sync with the PC so i'm guessing it may be hardward.
i tried a soft reset but cant see anything so cant confirm that i am doing it right. also tried taking out the battery for a couple of days but no luck.
Any ideas?
Cheers,
sunnyd

Most likely the screen is broken.

hi
are you try hard reset ?

White screen again and again
I know this post is quite old, but I can't find a clear answer about this problem...
My Atom stop with a white screen (colored,thin lines appear on the screen.Then the screen slowly turns to white)...
I must remove the battery and reset it to launch it again
I tryed everxthing... ROm update from the original firmware, PDAVIET (3 version on WM5 an WM6)
lot of resets, hard and soft...
This problem appers all the time... but randomly... 1 hours, 5 hours or 2 days after a reset....
Can you help me...
RGS
Fred

Related

Has it died??

My O2 XDAII is 10 weeks old. After using the internet and the screen freezing I SOFT-RESET it. Now the screen will only flash with the O2 logo between the backlight coming on and off and a few letters/numbers at the bottom right of the screen. Ive never had any problems before...I cant soft-reset, hard-reset or (it seems) to be able to charge it. The only way in which it stops 'flashing' is to take out the battery. Is there anything I can do at home?? (as you probably guessed Im a novice at all this!)
Any help would be greatly appreciated
Many thanks, Rob
This happened to me just yesterday, although It happened in different circumstances. Baiscally, I went to turn the phone on and it wouldn't (with any button.) I tried a soft reset and all that happened was the O2 screen appeared with the backlight flashing on and off every 10secs.
Before trying a hard reset I waited to see what would happen when i connected it to the cradle at work. Soon as I connected it. it switched back on, but it was as if it had done a hard reset (ie everything I have installed was erased. Good job I made a backup!).
Basically, it seemed to rectify the problem once connected to the cradle, which hasn't happened to you I know, but i thought I'd let you know that I got the same "symptoms".

XDA Exec, STUCK ON SPLASH SCREEN

Ok, Ive got a new problem with my XDA Exec.
Opened it up and tryied to turn on the backlight and nothing. tried a soft reset, nothingtried a hard reset now it just sticks on the splash screen, the red writing comes up on the right and side and just hangs there forever!
Please help
You're stuck. apparently the only remedy is turning it in to repair. For most of us it is under warranty.
Just off the phone to 02. Theres sending me a new one via courier on monday. it's less than a day old.
Is this a comon fault with the Exec?
erm ... I managed to experience this problem.
I was trying to uninstall SPB GPRS thingy that comes with the O2 package, and it just wouldn't go. I ended up deleting the program files and getting an error when it started up, so I deleted the GPRSNotify file under Startup. It never worked again ...
I got the splash screen, tried soft and hard resetting and various permutations (including standing on one leg and while holding breath) ... nothing. Did try to install fresh ROM, but startup wouldn't get far enough to let PC load ROM over USB.
Ended up contacting O2 who sent me a nice shiny new one, as it was only three weeks old. This time I haven't installed GPRS monitor thingy, and I don't intend to fiddle with it again ... or at least until I've forgotten my lesson ...
Sorry i ment to give you guys an update on this. I did manage to get it working again, although i still accepted the new one the sent to me.
What i did was installed a new rom off the 02 website. at 1st the computer couldnt see the phone so wot i did was enter what i think was the programming side of the phone. i found the instructions on how to this on the net. i think i pressed the 2 soft keys and the light switch while pressing the reset switch with the stylus (i think that was the buttons but unsure as i cant find the page again) when the screen light up again there was some faint writing on the screen with the word serial or usb. Double clicked on the rom file and 30mins later my phone was revived.
Funny it was the gprs monitor that i too installed before the phone screwed up? ive since installed it again on the new phone and have had no problems with it since.
trickydickyd said:
I think i pressed the 2 soft keys and the light switch while pressing the reset switch with the stylus (i think that was the buttons but unsure as i cant find the page again) when the screen light up again there was some faint writing on the screen with the word serial or usb.
Click to expand...
Click to collapse
Otherwise known as Bootloader mode
Aye, thats the one.
Cheers

White screen in TyTN

Hi,
I bought my TyTN 6 months ago. I upgraded it to WM 6 from HTC update and and few weeks later during wirting a text message my screen went white and I couldn't do nothing. I restarted it after 15 minutes and I discovered that all data is gone. I got plain OS.
From that time the situation was accuring again, but after few seconds it was working ok and white screen was disapearing. I was using different OS versions, as well as Shap's form 3.54 up to 4.31 but it on every the situation become the same.
I contacted with HTC but still i didn't get any reply. Any idea what the problem could be? Is it the screen? Please help...
KaPeer
It's probably flex cable problem. There's been a few issues this type.
hmotwr said:
It's probably flex cable problem. There's been a few issues this type.
Click to expand...
Click to collapse
Do You know is it possible to fix it and if YES how to do this?
im having the same problem with my softbank xo1ht. if i hard reset screen returns but after about 15-30 mins screen fades to white and i cant see anything or use any function??? please advise
My screen was going white like for almost a week (coincidentally after going through airport security xray). I called for a warranty replacement and wouldn't you know it, after I called I have yet to see the white screen on the old one.
Are your hard buttons (d-pad, answer, hang up, mail, IE) failing as well? Try pushing down on your device right under the bottom right of the screen and see if it'll turn white.. or put it in standbay and press down above your d-pad and then take it out of standby and see if that fixes it..
your probably running into a hardware problem which is discussed here:
http://forum.xda-developers.com/showthread.php?t=321163&highlight=white+screen

Anyone! Freezes, weird image and hangs...

Hi Everyone,
I'm having some issues with my P3600.
Sometimes (to many times in the past days) while making something on it, the image on the screen suddenly mess up (freezes and weird image) and hangs. Then after the soft reset, somethimes the image stays black, and finally on the 5\6 try it boots fine...
Also noticed that this occurs more while connecting the usb cable jack to sync...
Already make some hardresets and some rom upgrade tests... Also tryed some wm61 cooked rooms, no luck.
Anyone already got this? I think there's must be some problem on the flat cable that connects the lcd-board. Can anyone help me whit some more ideas... before I decide to open it?
Thanks In advantage
SteelwarrioR
it happens the same to me... the pixels all messed up... i dont know wath is the problembut i think its the flat cable ... becouse i have open it one time 3months ago and now its fine. now yesterday have done the same thing
sorry my english
Ok, I open it last night based on the service manual I found somewhere on the Internet, the flat cable looks fine... Now this morning this same situation occurred again, this time while unplugging the usb charger. I Think there's must be some problem on the usb connector. The usb connector is part of the main board so it could be a hardware board issue? Anyone got this on problem on Trinity? Any troubleshooting tips ideas will be appreciated...
SteelwarrioR
hi,
same here. trinity hangs up after some time, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts. I already changed the simcard and removed the sd-storagecard.
The vodafone hotline adwised me to send it in. Seems to me like a hardware issue.
My trin is about 1 year old.
(sry for my bad english)
Andi
No solution Yet???????
hi,
same here. trinity hangs abouth 3 or 4 time a day, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts
hi, the same to me... it's like the rom's, after a few soft reset couldn't find the necessary files to start again.... and sometimes, after meny tries, it starts well... it's like the ppc processor gets tired and goes to stand by..... it starts freezing the display, and loosing some pixels. so the only things to do is soft resetting the device... any solution? thanks
same with my htc - it appears to me that the errors occur when the trinity was used for a while and the processor was getting warm. the files and folders on the sd-card show strange symbols. but i have also problems when i stick out the sd-card completely.
i will send it to htc repair center - i just hope that they will not send it back as the errors occur only frequently.
so long,
bjoern
solution solved
take taste power and center ok reset take few sec to powering and phone starting
or power and run and stop call reset and phone starting on factory powering
not solved at all
sorry no - this is not the point - i think all guys here have (hard- and soft-) reset their Trinity more than 50x!
the problem is that once the software has crashed you can`t reset it for about 20min - it seems that the processor has to cool down or something like that - after a while (if I´m lucky) my P3600 boots as normal.
I already flashed several new roms - same problem with all of them - I`m pretty sure it`s a hardware failure.
Hello, i don't have any such problem, my Trinity runs very stable even with cooked roms. but sometimes Mobile navigator 7 takes too much memory so the System becomes instable and i have to softreset it.
Hi, mine bug also, and that's begin 2 or 3 days after I have flash to the 1.56.70.11 Radio Rom....
mine worked fine for about 1 1/2 years but suddenly it crashed continous. i havent flashed it and allready hard reseted several times on different days. sometimes it worked for a while but hangs if i started a bigger app like tomtom. vodafone told me they will exchange my p3600. now im waiting for their call
E: Got a new one today which works perfectly so far!
Hi guys,
has anyone had this issue solved without swapping the device?
I have the same problem.....
Bye
Petz
Same problem here...
I have to sftreset or hard reset several times to get it runing again...
In my opinion its some kind of problem with the processor...
Stiil i'm hoping this is a software insue... so that sone one have a hotfix for that...
For my part, when my Trinity crash, I remove the mini-SD, the SIM card and the battery. I just re put the battery, restart (soft reset until WM has realy start, and no more touch or screen freezes), I replace the sim, restart again.. and finaly I replace the mini-sd. It's very long, but generally works well
EDIT:
Finally, I better make my tongue and keep my method for me because at evening begin, my trinity crashed and impossible to turn it on until I finally come back house and have no need more...
my hand that it will crash tomorow morning juste after leave to works
hi, i started getting the same problem.
only thing different is I upgraded to wm6.1 (Mary SL)
I took it back to wm6 which was still locking, then down to wm5.
1week later no issue!
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
just a thought!
xpuser8334 said:
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
Click to expand...
Click to collapse
I don't think so because I downgraded my Trinity to original WM5 and, even if there were less crashes, it crashed anyway.
Now it's still with WM5 but it doesn't start anymore, only backlight.
Ciao
Petz
I want to let you known that my Trinity has run ok for 5 hours without any issue after putting some paper between battery and metallic plate under the battery.
I had to press a little over the rear cover to have it placed correctly because the battery is higher than before.
Keep in mind that it stopped running completely 3 monthes ago, it didn't start anymore and it didn't even go into bootloader mode.
Now I'm using WinMobile 6.5 beta........
Ciao!
Petz
Hi Guys , i have Trinity P3600 in Egypt ,,, it worked perfectly for more than 2 years , but last month it make the same problem like mentioned b4 , hangs , stuck in boot image , or mess in pixel ,,, and i tried to downgrade but no luck, i tried to use different Radio ,, it works sometime , but after a week no , i tried to take out the battery and wait for 3 hours , then back again , so it works but again it hangs if i start my GPS (IGO8) or heavy programs/.
any solution pls
Thanks

Problem while booting my trinity phone

Hi,
I have got my trinity phone one year ago and never had a problem since last week. When starting my phone, it stops on the first screen (with "orange" logo) and nothing more happens.
I tried to reset it without succeed. The phone is not detected by the "activeSync" to make it flushable.
Help please !
Yves Florent CK
my problem is mor or less the same... only that dont apears any image on screen and the green led is constantly on...
I have loaded a long time ago an old version of ROM Gelly.
This ROM worked perfectly to a friend who suggested to do the same with my trinity.
The PROBLEM is that when i try to open the pda it freezes to the first srceen showing the rom version and after....nothing!
I tried to load again Gelly from the bootloader, it begins to run, it runs about 1% then the trinity makes a flash (this means it loses the connection with the pc) and then shows me again the first screen....
Please i need help!
me to. i try install the rom original and my pda is living again.
try this to
hi,
2 things ...
have you tried a hard reset ? (hold both softkeys & hit reset button)
and when flashing:
when you first run the rom upgrade from PC with phone on Activesync, it is quite common for phone to hang at the bootloader screen ...
worry not -
just re-run the upgrade from PC again immediately, without disconnecting or attempting to switch phone off.
(the word USB should be visable on device under the coloured bars)
if you do get hung up at bootloader screen a hard reset should at least get you back to where you were, and you can try re-flash again.
hope this helps,
regards,
Kevin
My trinity won't work anymore...
Hi all!
My trinity wont't work anymore. When i press the ON/OFF-button, the display is lighten up a bit, then the buttons are lighten up. And nothing more.
When i will go to bootloader mode, it is the same.
And when i will to a hard reset, the trinity ask me to press SEND or END key for restore factory default or cancel. When i choose the SEND key, on my display some ridicoulous letters appear, but nothing more.
When i try KITL mode, everything is the same.
Can someone help please?
Because i can't do something on my trinity
EDIT (maybe this can help my helper ):
After some time, the display and the buttons are not lighten up anymore.
When i try to charging the battery, it only works, when the buttons are not lighten up (when i switch on, charging is ok; when the display is lighten up a bit, charging is ok; when the buttons are lighten up, charging won't work; when the display and the buttons are not lighten up anymore after a time, charging is ok)
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
never mind... problem solved... tks anyhow
weezer_88 said:
never mind... problem solved... tks anyhow
Click to expand...
Click to collapse
ok solved...
Can you tell how you did it?
Thanks
weezer_88 said:
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
Click to expand...
Click to collapse
But my trinity don't go to the boot screen, nothing on the display but lighten up slightly...
Nevertheless, can you please post, how you solved your problem?
THANK YOU in advance!
I downloaded the original Rom windows mobile 5 from http://www.htc.com/www/SupportDownload.aspx?p_id=3&cat=2&dl_id=111 then entered in KITL mode, connected the usb and reinstalled the original Rom, and all was fine...

Categories

Resources