Related
My blue tooth fortuna clip on will not respond to the XDAII with the updated rom, which suports serial ports. has anyone else had this problem, do I need to down load the BT tools patch again & if so can some one remind me of the web address
Ta
HI i have the GPSmart BT verision
and i have alos updated the ROm on my XDA II
all i can say is it works very very well i did have a delay when using
TOMTOM and that has now gone
Hope this help you out
I am also using the BT GPS Clip-on with the XDA II. Works perfectly after the O2 update. I'm using Tomtom 2 with the 2.09 GPS update from their website. Im not using it with the com port option, I'm using it as a Tomtom BT device.
Foruna clip on problems
I still can't get the tom tom gps driver to recognise / show information from the Clip on BT gps. I downloaded the latest driver from the tom tom site but still no luck. tom tom's gps drivers do not show the fortuna clip on. I have tried rebonding it with and without the serial port option. When I'm in the tom tom GPS page what GPS driver do I need and what com port do I select and do I need to set it up as com port 5 when I bond the gps????????
Well if you have the rom upgrade installed and you are using V 2.09 of the TOMTOM GPS drivers you can select
the device a TOMTOM Wireless GPS
and set the com port bit to Bluetooth GPS
I use this setup and have never had a problem
Hope this helps
I tried that but no luck, it would not show any satelite info on the gps pages. I notice in the blue tooth settings you can select com ports 4 & 5 for recieving and transmitting , what should these be set to? also when you bonded the fortuna, did you select the serial port option ?
Ta :x
Hi
It souds like you dont have the latest ver of the gps drivers fromtomtom installed
on V2.08 there was no mention of Bluetooth so i think you have that ver installed
And yes when i bonded with the GPSMART it asks me if i want to use the serial profile
Do you have ver 2.09 ? if not i can post it on here for you
pjcltd said:
Do you have ver 2.09 ? if not i can post it on here for you
Click to expand...
Click to collapse
Please do :lol:
OK here is the GPS Drives as from the TOMTOM website
pjcltd said:
And yes when i bonded with the GPSMART it asks me if i want to use the serial profile
Do you have ver 2.09 ? if not i can post it on here for you
Click to expand...
Click to collapse
sundownerspars said:
Posted: Sun Apr 04, 2004 20:38
I tried that but no luck, it would not show any satelite info on the gps pages.
what should these be set to? also when you bonded the fortuna, did you select the serial port option ?
Click to expand...
Click to collapse
I too have same problem - have 2.09 gps but now not getting info, it bonds ok, but won't display any tracked sats, do i need to say yes to serial when bonding?
Yes you must say to to it or it will not work
(that is if you have the updated Rom installed)
pjcltd said:
Yes you must say to to it or it will not work
(that is if you have the updated Rom installed)
Click to expand...
Click to collapse
All working now :lol:
now the back light drops out
I have tried reloading the ROM upgrade and reloading the Tom tom 2 software and latest drivers from the Tom Tom site (ver2.09GPS driver)
I still am having problems with the fortuna GPS. In tom Tom GPS it does not show any satelites and the little sat dish to PDA legends on the right hand side show no communication
Now the Back light drops out without warning and when I check the back light settings it has reverted to no back light on the battery power! (yes the battery is fully charged) and I keep getting a communication error popping up saying (cannot start communications with desk top computer" and the XDA 2 is not even in it's cradle
HELP!!!
I'm tempted to send it back to O2 for them to sort it out. :evil:
I have used fortuna gpsmart with xda2 with standard rom and had no problems, is it possible for you to download the launchrom from the O2 site and see if that will get you back where you started. You could also try unbonding everything then after loading the latest bthtools rebond and try that.
It worked fine with the original ROM & BT tools patch. I cant find the original rom on O2's site. May be I downloaded a corupt version even though it said updated ok? It took so long to down load on a dial up connection ( Damn XP at work on a broad band connection wont let any one apart from the administrator download programs!!!)
Do O2 send out discs with the rom update on them?
Also just noticed, when I try to turn it off on the power button all that happens is that the backlight turns off and the isplay is still there allbeit very faint. Still at least my BT200 works now!
I had the same problem for a few days after I got the Fortuna, but all went OK, not sure how I did it really, just kept, trying
I wonder if anyone can help me with a problem, sometimes I want to start TomTom2 with no GPS, just to do a quick route for someone, but when I start it, it locks up (presumably cause it cant find Bluetooth), I cant go into the GPS app to turn GPS off with the tick. The only way I can do it is turn on the Fortuna, THEN untick in the GPS app - very messy. Is there anyway to start TomTom without GPS/Bluetooth active?
I have the tomtom navigator 3 and a EMTAC bluetooth antenna and this works perfectly
My problem is that when I'am trying to employ other softwares like VITONAVIGATOR, GPSDASH ,INTELLIGOLF, and so on I cannot configure the softwares to recognize my antenna.
Kindest regards
@[email protected]
hi,
solution is simple...
sorry to say it, but uninstall TomTom GPS or better the whole TomTom and use Mapsonic or Mapopolis instead of it...
i did the same.
buzz
emtac
Yes of course but i already bought tomtom, is there any other solution?
Simple, in Remove Programs uninstall TomTom~GPS.
This won't prevent TomTom from working but will stop TomTom locking the BT Com Port for its own exclusive use.
Plenty of discussion of this on our website, see our detailed explanation here.
@griffog
man, that's an excellent guide there... really good one...
;o) basically i meant the same... ;o)))
but, tomtom needs also far more processing power than other comparable programs, that means battery drains 30% faster, slower UI response, etc.
i know, battery is not any issue if you are driving, but i sometimes walk as well... )))
anyway, i don't like tomtom...
do you maybe know, is it possible to do crossborder routing in newer tomtom versions? like you can in mapopolis?
THANX
buzz
It looks like TomTom v5 will do cross border-routing yes. I have never experienced slow response to the UI except when using SD for map storage on iPAQ2210's. Using CF resolves this.
v5 also introduces walking and cycling modes which alter the route calculations. What PDA/GPS/memory Card Combo do you use?
darren it our work around doesnt work for xda2
griffog said:
It looks like TomTom v5 will do cross border-routing yes. I have never experienced slow response to the UI except when using SD for map storage on iPAQ2210's. Using CF resolves this.
v5 also introduces walking and cycling modes which alter the route calculations. What PDA/GPS/memory Card Combo do you use?
Click to expand...
Click to collapse
hi griffog,
i'm using XDA2 + EMTAC BT + Mapsonic or Mapopolis.
Maps are on Transcend 64Mb SD card.
i'm very satisfied with this combination
buzz
just being playing with mine :lol: :shock: eerrrr right
first delete gps 2.07 or above then soft reset the device install pocket bluetooth tools delete the pairing with your receiver repair then ( during which you will be asked to create a serial port for this device select NO at this point then intall gps 2.06 available from www.pocketgpsworld.com this available in the downloads section under tomtom gps drivers.
download the cab file and copy it to the xda2 and then exicute it from file explorer select you reciver and away you go
well thats how i did it hopefully the above ramblings make sense :lol:
Alix, how will he configure the other gps software if no serial port has been assigned, I understand this works under tomtom as "bluetooth gps" but I am not so sure it will work with the software he mentions.unless you have tried it, if so how did you configure it.?
bluetooth tools asigns the comport to com7 not sure hows these thing work really it just worked for me i can run tomtom 3 and copoilt 5 on the same machine
Hi guys!
Just learned of this forum, it might be my last chance.
I bought the GlobalSat SD-501 GPS secure digital receiver in Hong Kong. It was a big gamble and it turned out to a headache.
After installing the thing you are supposed to be able to see which comport it has received using the nifty utility "GPSInfo" from GlobalSat.
It is supposed to identify itself as COMX: MANF-0501-CARDID or something similar.
... but after loading the program I see the following:
COM1: Serial
COM2: Serial_Cmd
COM3: IrCOMM
COM4: BTIBserial
COM5: BTOBserial
COM9: Serial_Data
That is, nothing that resembles anything what I want. I tried to force select one of the following ports but of course that didn't work. There are also 3 different drivers to test, the one supplied on the cd and two on the developers site, found here:
http://www.globalsat.com.tw/english/download.php?level_id=3
I have tried all three drivers with no effect. I have also tried soft resetting after install and even a hard reset to see if that would solve any issues.Along with the drivers there is also a program called COMKiller that disables comports (after surfing found out that most IPAQ's tie up all comports leaving nothing for the GPS), I tried this as well with no success.
The LED on the GPS is supposed to blink when it has your location fixed, the device actually does that after a while so it seems to have a working hardware anyway - it just won't talk to the phone.
From looking at other forums it seems as this device work for people running the S2020 (the Himalaya) so maybe there is hope.
In summary this is what I have tried:
1. Tried all three drivers available from maker.
2. Soft resetting.
3. Hard resetting.
4. Upgraded ROM to the version described below.
5. Disabled IR (incoming beam).
This is what I have:
Qtek S100
ROM: 1.06.00 WWE
ROM date 01/06/05
Radio version: 1.05.00
Protocol version: 1337.39
ExtROM version: 1.06.115 WWE
Model NO.: PM10A
Maybe there is something in the driver that is trying to access the S100 in the wrong way, maybe it is trying to force select a busy comport. I don't know. Please you kind devs and others, can you maybe take a look at this?
best regards
Kristian
I querried this forum about this about a month ago and had no luck.
I have an o2 mini. When i plug the sd501 into the mini The light doesnt come on. My friend has JAM. When I plug it into the jam the light comes on but still i have not been able to get it to work,
If you find a solution please post
Could any of you smart devs please take a look at this, I would be eternally grateful!
/Kris
Krillo said:
Could any of you smart devs please take a look at this, I would be eternally grateful!
/Kris
Click to expand...
Click to collapse
Hi Kris,
did you already try on the forums you can find at www.pocketgps.co.uk ???
IMHO that is the best-gps-experts website; if nobody can help you there, you can put your receiver in the recycle bin
Sorry I cannot help you some more
Hi,
yes I have posted in that forum too - awaiting response. But I am sure this is solvable, it's not rocket science. Well, for me it might be but I know there are some seriously smart people here eager to give support
/Kris
being a bit a GPS expert myself as well as an S100 owner I have not found a solution so far to get this combo to work, which I guess is not that bad at the end of the day considering you lose the SD slot for storage unlike with say a Bluetooth GPS. I will certainly revisit when they send me the SD-502 with its 512mb RAM, small helix antenna and SIRFIII chipset for testing in a few weeks ;-)
GpsPassion -> Do you have some kind of relation with GlobalSat? If so, have you had any comments from them if they will try to make this combo to work or not?
I mean, I like the device and it would suit my needs quite well - and I bought mine so I must decide if I should sell it or if there might bew a solution sometime. Do you have any contacts?`
best regards
Kristian
Hello Sd 501 "victims",
searching through the net I ended up at this thread. I also would like to run my sd-501 with my magigian. Is there really no solution to that problem?
Stefan
hi
the drivers arent installed properly you should have on there manufactors card under the com ports. reinstall the drivers andf it will work are you using the disk that came with it as the drivers you down load dont seem to work.
kevin
Nice to see an old thread coming back to life. I for one never managed to get the 501 to work on an S100 and the 502 is following the same fate, looks like some SDIO issues at HTC...http://www.gpspassion.com/fr/news.asp?id=410
just signed up today and this is my first post! anyway i am having the same problem. i have been trying to get the globalsat sd-502 to talk to my Qtek s110 without any joy depsite expansys saying it is compatible.
i have tried the drivers supplied and those on the globalsat website. it cannot see any com ports other than those mentioned earlier in this thread.
i do know from a local guy who tried to help me out that he managed to get it working with his xdaii which was not comaptible but he failed to help me out on with the qtek. i think this is one that globalsat will need to look at.
its a shame because it locks on to satellites just as quick as my globalsat bt-338 but wont suck the battery dry as quickly the bluetooth does. i will be interested to here if someone comes up with a solution.
tebs said:
just signed up today and this is my first post! anyway i am having the same problem. i have been trying to get the globalsat sd-502 to talk to my Qtek s110 without any joy depsite expansys saying it is compatible.
i have tried the drivers supplied and those on the globalsat website. it cannot see any com ports other than those mentioned earlier in this thread.
i do know from a local guy who tried to help me out that he managed to get it working with his xdaii which was not comaptible but he failed to help me out on with the qtek. i think this is one that globalsat will need to look at.
its a shame because it locks on to satellites just as quick as my globalsat bt-338 but wont suck the battery dry as quickly the bluetooth does. i will be interested to here if someone comes up with a solution.
Click to expand...
Click to collapse
Sorry to hear about your problems - but, what software are you trying? A good freebie is VisualGPS CE, and does work with the SD-501 (i use said GPS reciever with my Blue Angel).
But unfortunatly, I think this problem is purely a HTC problem, not global sat. Remember, they made thier device compatible to the BSquare SDIO Now protocalls - if HTC decides not to follow that , then it is not GS's fault (though, it is odd that they would support the SDIO on devices like the II, IIs, III, but not on other devices..)
Divine im using tom tom 5 but as far as gps programs ive used both gpsinfo and winfast as someone on the pocketgps site suggested. yeh it probably is something that htc need to look at.
thanks to a bit of browsing on here ive downloaded a trial verison of phone alarm which allows me to use a single press of tghe tom tom icon to activate the bluetooth and tom tom in one go. exiting tom tom switches the bluetooth off and the phone so i can power the device down. this will keep me happy till someone comes up with a solution.i am going to return the sd-502 to expansys and ask them to remove the qteks110 compatiblity reference on their site
considering getting tomtom5 for my mda compact.
anyone know whether its compatible, has anyone got it?
Should be. TomTom 3 and 4 worked fine.
By the way, Bakonl's release of TomTom 5 was just posted on alt.binaries.warez.pocketpc.gps, along with a few maps.
Benelux map only.. :x
TT5 does work
and not only benlux maps are posted. italy, france, germany, spain, uk are posted as well. rest will be posted as well i guess.
anyway, waiting for my legal TT5 to arrive (with the bt gps), woei =)
I can't get it working... I tried installing in the program files and in the storage card directories but it crashes at the end of the tutorial, just after that the "Welcome to TomTom Navigator" message appears in the map screen.
I can't see the map nor the GPS is able to connect (TomTom "3" Navigator Wireless).
I can't find any registry entry, I modified the currentmap.dat in order to point to /storage card/italia-map.
Anyone was able to reproduce my problem and to solve it?
Yeah, I noticed there are a few maps out. I'd like Scandinavia tho Seems like a buggy version too.. Crashes often.
Yeah... reeeeally buggy, I tried to check the post in the alt.warez.pocketpc.gps newsgroup for infos about bugs/problems etc. but I can't find it in my nssp server and using the web I'm not able to see the post (I can just see the header) so... I still can't use it :lol: ; maybe it could be a bad installer, I noticed that sometimes it won't install some cabs from the cd, or maybe it's just the italian map which is corrupt... who knows? 8)
I guess the release on alt.binaries is a preview or beta version.
The official release of Tomtom 5 will be end of June.
Im still waiting for Destinator PN on emule...
Where can i find the TomTom 5?
I have installed TomTom 5 to see if it works, I'm unable to connect my BlueTooth GPS (Holux GPSlim 236). The port does not show up on the device list under Buzz WM2005.
Does anybody know how to change this?
Ikkuh
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
JesperR said:
Where can i find the TomTom 5?
Click to expand...
Click to collapse
www.tomtom.com
Stefan
bruxelles5 said:
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
Click to expand...
Click to collapse
I had the same problem.... go to the bluetooth com ports, change the GSM to use COM8.
Then start -> settings -> gps, on the first tab set com4 and on the second tab tom com8. The thrid tab should have the checkbox set.
Now reset your device.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Now exit tomtom and reset your device.
Start tomtom and wait a while (can take a few minutes for it to find the GPS).
This worked for me (you need the resets in order to detect the com ports!!)
Ikkuh
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
dickr43 said:
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
Click to expand...
Click to collapse
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port, and attach it to the hardware GPS. If you do this and reset the device, the virtual GPS will show up in TomTom (in my case it did ;-) )
Ikkuh
I must admit dickr43 has got a point. Even though you are trying to be helpful, Ikkuh, it's a bit hard to understand.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Click to expand...
Click to collapse
There IS no GSM setup in TT. Most likely you mean GPS?
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port
Click to expand...
Click to collapse
Doesn't exist either. Must be some third party app you have installed...
dickr43,
Try removing your GPS pairing from the Magician. Go select the 'Bluetooth Setting' icon under Settings/System and make sure both the serial ports are activated. Note which COM port is 'Outbound', then re-pair with your GPS device. Start TT and in the GPS settings panel, you should get things running by selecting the COM port that was marked for Outbound.
Unless you are running some third party software with virtual BT COM ports, that should get you up and running. If you are, try each COM port one by one. Don't hurry through the ports, but give it time to connect. 5-10 seconds at least. Also make absolutely sure your GPS is within range and has a satellite fix, or you are wasting your time.
I cant use tomtom 5 as a route map
I just want to use it sometimes without the gps module is it possible. Because with the older version it was possible to select a GPS simulator.
THX :lol:
The "unofficial" versions of TomTom5 doing the rounds seem to have been taken from beta builds. I installed without any problems, but noticed a number of bugs (not recognising GPS, the program freezing, picking up wild GPS info, settings not sticking)... sometimes you'd think it was working, and you'd think you'd got it stable, but then they'd fall down.
I've tried 3 different versions doing the rounds right now and none of them are stable. I'll wait a month or so for a more finished release is available.
i got my hands on TT5 aswell, the program looks realy nice and lot improvement to TT3, but as mentioned above, it's not very stable, spontain exiting of TT5 is not cool when youre in the middle of no where.
my gps was recognized directley,
i just went to BT settings and checked Com5 and a messege apeared that i must bond with a compatible device, so i bonded with my GPS reciever and in the TT wizard i could chose Com5 and it connected right away, much easyer than TT3
regards.
Hi,
I am considering getting TOMTOM5 for my T-Mobile MDA Compact and would like to use this in my car. Does anyone know or can provide screen shots of what the display looks like? Is it easily readable while driving?
Thanks
Msuk
ok so i just upgraded to the gps rom....
what are some good maps i can install and use with this newfound gps function....
possibly free if not available for trial at the very least...
ok first things first, can someone post the settings i should have under my gps settings and program settings
i'm using googlemaps right now and it went through the initialization phase of gps fine and now its stuck at seeking gps satellites....
how long does it usually take to find satellites?
nvm got it to work......had to stand by the window
SWEET!!!!!
now get this going for the hermes and im in heaven! it will have EVERYTHING!
There's no built-in GPS on a Hermes. Yes, it does share the Trinity's GPS-capable processor and the same software, radio firmware and drivers work on the Hermes, but there's no antenna in the Hermes and no way to connect one.