Hello All,
My in car Bluetooth kit does not allow me to change the volume - The instructions tell me to control the volume using the phone, however the Dopod 838 Pro does not change the volume when using Bluetooth. If I try to change the volume on the phone while the call is using my car kit or my headset, it does not work.
Now I am stuck with a REALLY LOUD car kit, and no way of turning it down. Is there a tweak or a hack here for this?
Cheers
-J
Related
Hi all,
I use a THB carkit integrated into my stereo. It uses usb connector to power the pda but bluetooth to trick the pda into thinking a headset is in use so calls are handled by the carkit. Aside the problem of bluetooth intermittantly turning off, is there a way to forward all audio (especially tomtom) to the "headset" carkit?
I've searched the forum and there is plenty of info on bluetooth headsets and how the button on them can be used to start audio via bluetooth, but the carkit doesn't use any buttons. I would be happy enough if there is an app to run whenever I want audio over bluetooth, anything really to sort this out.
Cheers all.
Anybody have any suggestions pleeease?
well sounds like your in a tight spot. I believe that all the audio programs use the button to initiate the audio transfer. Perhaps if you look at the reg edits for these programs you might be able to toggle it with some other input from the phone.....
There is a free program called BTAudio that you could try
tried that program but it relies on pressing the voicedial button on a headset which I don't have.
Hey All,
Is there any way to control the volume of the call when using a Bluetooth car kit. My ute has a Bluetooth system built into the stereo, but the volume on the stereo does not control the volume of the call. The manual states to use your phone to adjust the volume, but the handset volume does not do it either.
Is there a fix or a way to get the volume dial on the phone to work with Bluetooth.
I have a car tat is installed with Bluetooth handfree system. But when i call/have incoming calls, the speaker volume is just too soft(damn my noisy car)... I've max out my volume bar(left side volume control) but no luck.
I guess the problem lies to the phone itself. Anybody can recomand me a solution? like a volume booster or somethign? I'm using O2 XphoneIIm (HTC Amadeus) with ALEUT's WM6.1 pre [1.3] installed.
Guys,
I've bought a Sony HBH-DS200 as a new headset for my Hermes. First impression: great! The headset sounds good, and AD2P works fine after installing the AD2Pfix for the Hermes.
But here is the problem:
The headset hasn't got a volume switch for phone calls, the volume had to be controlled from the Hermes. But when I try to change the volume with the volume bar on my Hermes, the volume on the headset won't change. And that's very anoying because the volume is too loud (and a little bit crapy).
When I'm listening music (AD2P) I can change the volume.
When I pair the headset with my Nokia I can control the volume and the sound for phonecalls is much brighter then on the Hermes.
Because I'm using CRC's ROM, I just reflashed my device to the orginal HTC ROM but the issue also persist with this rom.
Any ideas?
Note: I have also a Parrot CK3100 for my Hermes, I just checked: the same issue! But I never noticed it because the Parrot has a volume control.
Hi, i've the some problem with my plantronics free hands...
i can't control in-call sound with my bluetooth...
any idea?
I have tried the following (without any succes):
- adjusting the registry setting "spk volume" see this topic. I can make this setting but after resetting the device the dword is removed (and the volume isn't changed)
- Installed the Widcomm stack, after installing the ad2p signal is far too loud and the phonecalls aren't redirected to the headset
No solution yet, I will continue
im ot sure if this will help .... but i have the same HBH-DS200 a2dp headphones i had a slight annoyance with the sound being to low, on the head set hold the play button in when the set is turned on - turns the volume up on the headset! - hope this worked
I have the Plantronics 590's and can control the volume during a call from the headset. I am using CRC's 13.0 rom. I do not have the hermes A2DP fix on my phone and never have.
Hello Everyone,
I've got a USCC Vogue, which is running a wm 6.1 rom I cooked using PPCKitchen's Rom Kitchen. The strange thing is, I paired my Jabra BT8010 headset to the vogue, and it works great, until I turn it off. To get it to work properly again, I have to delete the device and repair, OR I have to put the headset in Stereo A2DP? mode, then press the play/pause button, after which I can switch back to phone mode with the headset with very few issues (ie, only the known MSVC1.6 problems.) I've tried using acbToggle to switch the audio gateway over to bluetooth, but the volume is low. I've also tried plugging in my headphones and then toggling, and that helps the low volume issue some, but not as much as re-pairing or doing the a2dp trick. Also, shouldn't the vogue automatically connect to my headset upon turning the headset on? Because I have yet for it to do so. Also, if I go into the Connections/Bluetooth menu item, I see the headset, and if I bring the menu up for the headset and select either Set as Headset or Set as Wireless Stereo, nothing happens. Is there some other way to set my headset to automatically connect as Wireless Stereo? (this setup gives me the best performance and volume)
Thanks in advance for any help/information anyone can give me.
Jamie
hudson_macbeth said:
Hello Everyone,
I've got a USCC Vogue, which is running a wm 6.1 rom I cooked using PPCKitchen's Rom Kitchen. The strange thing is, I paired my Jabra BT8010 headset to the vogue, and it works great, until I turn it off. To get it to work properly again, I have to delete the device and repair, OR I have to put the headset in Stereo A2DP? mode, then press the play/pause button, after which I can switch back to phone mode with the headset with very few issues (ie, only the known MSVC1.6 problems.) I've tried using acbToggle to switch the audio gateway over to bluetooth, but the volume is low. I've also tried plugging in my headphones and then toggling, and that helps the low volume issue some, but not as much as re-pairing or doing the a2dp trick. Also, shouldn't the vogue automatically connect to my headset upon turning the headset on? Because I have yet for it to do so. Also, if I go into the Connections/Bluetooth menu item, I see the headset, and if I bring the menu up for the headset and select either Set as Headset or Set as Wireless Stereo, nothing happens. Is there some other way to set my headset to automatically connect as Wireless Stereo? (this setup gives me the best performance and volume)
Thanks in advance for any help/information anyone can give me.
Jamie
Click to expand...
Click to collapse
The real questions is did it work before you flashed your custom creation? Is it possible that there is an issue with your ROM?