Dear Bros,
I have a very serious problem here with my 818pro, which noone may have encounter in this forum, let me tell you in sequence:
1)First, after I downgrade my rom with this file Customize_rom_PDAMobiz_Editon_Upgrade_Rom_for_IPLSPL_2.15.0001_v.1.02.rar, I was unable to power up from USB. I can only power up using the wall mains.
2)After powering up from my wall mains, I upgrade my OS using this file
AKU3.3.07.ASERG .
3)After upgrade and hard reset, I am unable to boot up using both the wall mains and even the USB! My display just went blank, and my two leds (orange and blue) keep blinking on and off.
4)I connect my 818pro using USB to PC but cannot go into the bootloader mode nor boot up into the OS.
5)I connect using my wall mains (but not link to PC) and is able to go into bootloader screen, but still unable to boot up into the OS.
Here, I am unable to perform any upgrade/downgrade of ROM using the mains power as I cannot connect to my PC at all!
6)Worst case, I do not have any ROM backup file on my SDcard, therefore am unable to do anything at all!
7)Lastly, can any of you expert brothers here able to advise me wat to do now, or able to provide me with any SDcard rom backup for the 818pro, as I guess that is the only option out for me now???
Would be deeply grateful to the kind brothers here for helping me out! Sorry for the long story which may be confusing.
Best Regards
valiance said:
Dear Bros,
I have a very serious problem here with my 818pro, which noone may have encounter in this forum, let me tell you in sequence:
1)First, after I downgrade my rom with this file Customize_rom_PDAMobiz_Editon_Upgrade_Rom_for_IPLSPL_2.15.0001_v.1.02.rar, I was unable to power up from USB. I can only power up using the wall mains.
2)After powering up from my wall mains, I upgrade my OS using this file
AKU3.3.07.ASERG .
3)After upgrade and hard reset, I am unable to boot up using both the wall mains and even the USB! My display just went blank, and my two leds (orange and blue) keep blinking on and off.
4)I connect my 818pro using USB to PC but cannot go into the bootloader mode nor boot up into the OS.
5)I connect using my wall mains (but not link to PC) and is able to go into bootloader screen, but still unable to boot up into the OS.
Here, I am unable to perform any upgrade/downgrade of ROM using the mains power as I cannot connect to my PC at all!
6)Worst case, I do not have any ROM backup file on my SDcard, therefore am unable to do anything at all!
7)Lastly, can any of you expert brothers here able to advise me wat to do now, or able to provide me with any SDcard rom backup for the 818pro, as I guess that is the only option out for me now???
Would be deeply grateful to the kind brothers here for helping me out! Sorry for the long story which may be confusing.
Best Regards
Click to expand...
Click to collapse
Hey man,you're not alone.. my 818pro do act like that sucks things as yours...
hoping expert's help ,too.....
solved...just replace a new battery...haha..
really? replace a new battery will help? why is that so??? my battery is still good , and the only thing i did to **** up the pda is just reflashing the rom to a wrong one.
what happen when u replace a new battery? can share?
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
hey thanks! i've successfully unbricked my 818pro and flashed it with os 1.013, a very early version, and only that seems to work! I had tried flashing to aku3.3 clean rom from pdamoviz but it stuck at the splash screen after successful flashing.
another funny thing, although i unbricked my 818pro, i can still only soft reset it thru my charger instead of usb. If i soft reset while on usb power, the device will just shut off and show blue and orange flashing leds. Do u have a workaround for this problem?
valiance said:
hey thanks! i've successfully unbricked my 818pro and flashed it with os 1.013, a very early version, and only that seems to work! I had tried flashing to aku3.3 clean rom from pdamoviz but it stuck at the splash screen after successful flashing.
Click to expand...
Click to collapse
hI,How did you flash the rom? You could not go into bootloader mode, nor connect through usb. Please give the procedure used, because I have the same problem. Thanks.
no and there are still a lot of problems for me... I bricked 2 batterys already for example but I'm working on it ... but its a little bit different as I flashed a Wizard bootloader and I have no idea what happened with your phone^^ but something else... I know the problem though, often my phone doesn't even bootup after soft reset if its connected to the charger...
cr0ssy said:
get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that
Click to expand...
Click to collapse
|I tried the same with my G3 JAMin and it worked. I have a G4 JAMi wth the same problem. I tried the above solution but di'd not succeed. Any ideas?
please need help!
i try to downgrad my "prophet" and now i have (boot loader mode) only with AC adaptator and i see this: "
"get the battery out.
cut your charger cable open
the inner cable, the one inside of the inner white one connects to pin 1 from the physical top.
the outer one of the charger cable connects to the fifth pin from the physical top
no you go into bootloader and connect the usb cable, flash over another rom and try if it works... GET OUT THE BATTERY BEFORE YOU CONNECT THE PINS mine got damaged because of that"
but my english is not well, can you try to explend me in french or by a graphic please?
Hello,
this is what the problem is, the power button doesnt bring it back to life. i do a soft reset, it says press zero to clear, i do that it doesnt work. then i do a hard re-set and it shows 'serial', i plug in the usb and it changes to USB (think that's what is called the boot loader'.
now i ran teh exec official firmware, it managed to update it onces but after that i did a soft reset and it didnt come to life. i repeated that process again but this time the firmware didnt even manage to communicate with the device as it said unknown usb device. and then i got an error 101, connection error
any ideas whati can do to make sure it gets restored, i am really going nuts now!!
Same Problem
I am having the same problem with my 02 exec. My phone keeps on being in bootloader, I have tried mtty and I don't have usb connection. Hmm I have tried uni_exitbootloader ,but it tells me that it can not open my usb port. Which sucks. Truely and I am stuck. I am running vista. So I am stumped because I don't know what else to do.
Me too
I am stuck on bootloader page the one that says USB at the top and V1.00 at the bottom. I have Vista so can not use mtty or the other one. I have turned off the USB on Windows Mobile thingy from Vista like activesync. I can get the white screen to show O and X for either factory reset or exit. And I have tried the bootloader screen as noted above. So can anyone help?
i got it working for 2days and then when i was on wifi, it crashed again and wont start again, i get to serial/usb mode of bootloader and also to hard reset when i press 0 to clear everything. but then it doesnt start again.
i thought it was something to do with the battery so i put in a new battery but that still doesnt help.
can someone send me a link to mtty and what to use it. i shall give that a try again.
thanks
mines just still stuck
same im still stuck in boot loader wont budge from he bootloader screen with serial v1.00 on cannot connect via usb as the connection broken i use a extrunal battery charger and got serveral batterys any help yet?
Hi all, I am a noobie at this and I think I have done somrthing wrong somewhere. I have a XDA Exec and I atempted to load Bootloader 1.01 Update, the problem I have is with the USB pluged into the computer the only thing on the XDA screen is USB V1.00, when I unplug the USB cable the screen say's serial v1.00. Cant seem to get it to connect to pc or anything else as a matter of fact Could someone please Help meeee.
With no warning, my phone froze today (it's done it a few times, but a soft reset's fixed it) and nothing, including a hard reset, seems help.
I can get into bootloader and hard reset screens, however it gets 'stuck' on the Orange splash screen. The numbers in the corner flash up for a split second and then disappear.
I haven't been flashing ROMs, I just picked it up and it stopped working. I have tried the instructions here (http://wiki.xda-developers.com/index.php?pagename=Prophet_recovery) but the computer can't connect to it (both with Active Sync on or off and Active Sync USB connection on or off)
Can you make any suggestions?
Thank you!
When you go into bootloader, do you see USB on the screen? Wot are your IPL and SPL?
Im surprised flashing with Jesterz did not work, that was my first step in recovering mine and it worked
When you tried this, did you unplug all other usb from your PC? try another cable? sounds daft but only one usb port out of 4 worked for me. Give some more info on what you did and what happened?
I have problem in my HP 6815rw, during update software my handset turned off because of my computer reboot and now it’s like a dead and not able to turn on and only red light appear when charging or usb cable switched is there possible that its loader reload again?? pls help me accordingly
Regards
Mani