Hi,
Just wanted to share the latest camera app with you.
Originaly it was a german version but I made it english.
Also I changed album.exe and put a Exit command in the
menu.
First you need to install Camera_Wizard_Magician_T-Mobile_WWE_RC28_Customize.CAB
Then overwrite both camera.exe, album_res.dll and album.exe from camera_album.zip.
These 3 files are upx-ed to save memory.
The camera.exe is from Camera_Wizard_Magician_T-Mobile_GER_RC29_Customize.cab (version 2.70.0.21104)
One thing that still is bad is when the camera ambience is in Auto.
It still is not working as it should. Better operate the Ambience in
DayLight or Night mode.
The magician can have 2 kinds of image sensors. Mine uses hklm\drivers\builtin\camera_sensor1.
You can fiddle with the LightSensorHz a bit. Default it is set to "50" but you can try "0" or "100".
Could not find much difference.
You can check which camera_sensor driver is active by going into
hklm\driver\active and look for Name: CAM1: or CAM2: (CAM2: in my case at key 25)
Some other camera related tweaks (decimal dwords):
hklm\software\drivers\camera\Property\02 (or 01 in case of CAM1
brightness 6
contrast 5
hue 5
saturation 4
sharpness 6
hklm\software\HTC\Camera\AppDefSettings
country 2 determines the display rotation on camera start
flashlight 0 can be set to 1 but you don´t have one
hklm\software\HTC\Camera\AppDefSettings\common
fontcolor 00ff00 rgb values for osd
keycolor 080c08 rgb
hklm\software\HTC\Camera\AppDefSettings\general
brightness 6
contrast 5
hue 5
saturation 4
sharpness 6
EnableCallBack 1 some calibration value osd
EnableFrameRate 1 osd actual framerate
EnableDayTimePath 0 creates subdirs in my documents\my pictures if 1
EnableHopper 0 test/debug program called hopper.exe
EnableIPSM 0 enable IP Streaming Media, never got it workin anyhow
hklm\software\HTC\Camera\captparam
captureduration 60 force recording time to be 60 seconds
delaytime 10 dunno. 10 ms calibration time before recording starts?
savethesamename 0 for debugging, always save recording under same name (debugsometing)
hklm\software\HTC\Camera\general
brightness 6
contrast 5
hue 5
saturation 4
sharpness 6
hklm\software\HTC\Camera\RecParam\general
audiobufcount 30 nr of audiobuffers
enablemp4vdodupl 1 dunno
videobufcount 8 default is 4 (max is 8)
hklm\software\HTC\Camera\RecParam\3gpsmall
hklm\software\HTC\Camera\RecParam\3gpmedium
hklm\software\HTC\Camera\RecParam\avismall
hklm\software\HTC\Camera\RecParam\avimedium
hklm\software\HTC\Camera\RecParam\avilarge
hklm\software\HTC\Camera\RecParam\mp4small
hklm\software\HTC\Camera\RecParam\mp4medium
hklm\software\HTC\Camera\RecParam\mp4large
cachesize 8192 default is 4096, add to all 8 keys listed above
All settings for camera and album are stored in the key
hkcu\software\IA Style\IA CameraWizard(Pocket PC)
The camera app is version 2.70 the album is 2.51
You can remove the keys like preferences and strings or UI info to reset
the default values.
hklm\software\HTC\Album\DisableEditor
Disable 0
EDIT: 4 apr
Command line options for camera.exe, so you can make shortcuts yourself.
-c or /c perhaps assign to contact (if you have smartdial/iacontacts installed)
-i or /i switch to photo mode
-m or /m switch to mms video mode
-p or /p switch to contact photo
-t or /t switch to picture theme mode
-v ot /v switch to video mode
Still looking for a way to enable rotation and the paint appl in the editor.
In the resource file the images are there (see attachements)
EDIT 5 apr.
The UI interface mechanism is getting clear. If you put album_res.dll (a resource file) in ResourceHacker you
wil find the BMP section of the resources. The BMP i´m interested in is 920 (see attachement below).
If you count the number of icons in that picture you get 10.
Now goto the 241 section. There you will find a 920 resource too. It reads:
01 00 10 00 0F 00 0A 00 0C 91 0D 91 0E 91 0F 91 F9 8C 28 8D 29 8D 2A 8D 2B 8D 18 91
(there is a bug in resourcehacker that doesn´t show the last pair of digits of a 241 resource)
Look complicated at first look. But it isn´t. Lets try:
01 00 10 00 0F 00 = always the same in every 241 resource
0A 00 = 00A0 is 10, so then commands/function id´s follow
0C 91 = 910C = 37132, and is the command for PAN (remember the first icon
in the 920 BMP?)
So (see album_res_920_1033.bmp):
910C is PAN
910D is CROP
910E is RESIZE
910F is COLOR ADJUST
8CF9 is SAVE (dec 36089, and can be found with Resource Hacker in
resource 242 in the Menu section, named Save ;O)
8D28 is ROTATE CLOCKWISE
8D29 is ROTATE ANTI CLOCKWISE
8D2A is MIRROR HORIZONTALY
8D2B is MIRROR VERTICALY
9118 is goto PAINT menu
To be continued
Anybody found a newer version for wm2003se?
Happy tweaking!
Thanks for this
thanks
but IMHO coolcamera anyway is much better than a default one
hi shoonari... i agree, but can u help me find the latest ver. of coolcamera and its cr**k?
here it is
A bit late, But it works nicely.
Thnx
Related
Just got my Qtek 9100 today and I tried to tweak the date/time display on the top right corner of the display, ie. go to shell and create binary value TBOpt 13 00 00 00. And unfortunately... the time is fine, but the date is in BOLD format, so I couldn't see the year. That is, it looks like this:
25/11/0
18:05
-> only 0 in year part, 5 is missing. Any1 how to do it properly? Pls show me. thnx ^^
I've been searching for 2 days, but nothing so far. I think Universal users have this problem too.
spb pocket pc tips & tricks
Have you guys tried spb pocket pc tips & tricks? This will perform this tweak for you, although the value mentioned TBOpt 13 00 00 00 is the same on my magician.
I deleted the key TBOpt from HKLM/software/msft/shell, and the time is still there in bold.
I tried tweaking with battery pack pro, but they only add the 13 00 00 00 value into the TBOpt registry.
I haven't seen a fix for the bold font yet. I tried the Universal registry tweak, which allowed me to change the date to a M/DD format that was not on the regional settings list.
The problem is it also made the OK button go away. Made it a bit difficult to close my programs, so back to the bold.
I have made my cube with 6 sides but now i want to make the sliding of the cubes with my new icons.
When i open my registery and when i look in HKLM - software - HTC - Biotouch - Boitouch -
i copied the values Cube 2 and renamed it to Cube 3 - Cube 4 and Cube 5.
The original Cube 3 i renamed as Cube 6.
When i now slide my cube and go from the phone screen to the mediahub screen it is ok, form the mediahub sceen to the 1ste app screen is ok, but form the 2° - 3° and 4° app screen i got the same pictures as form the 1ste app.
I look at the values in the Cube and i notice that in Cube 2 there is :
07 07 08 09 0A 0B 0C 0D
0A C8 C9 CA CB 18 19 1A
1B 1C 07
Since i copied Cube 3 - 4 and 5 with the same values as cube 2 the values are the same.
In my cube 6 (original cube 3) i have these values :
07 0D 0E 0F 10 11 12 01
0A C8 C9 CA CB 1D 1E 1F
20 21 0D
I have already figured out what the numbers 01 till 33 are (they are also in the same register and have values for moves of the cube)
I made new strings form 34 till 66 with the values for the moves of the other cubes.
I can't figure out what the other things will mean like 0A 0B 0C 0D
0A C8 C9 CA CB
Can someone help me to make my 6 cube slide with my new icons on it?
Thanks
This would be an interesting find... * bump *
hefi said:
I have made my cube with 6 sides but now i want to make the sliding of the cubes with my new icons.
When i open my registery and when i look in HKLM - software - HTC - Biotouch - Boitouch -
i copied the values Cube 2 and renamed it to Cube 3 - Cube 4 and Cube 5.
The original Cube 3 i renamed as Cube 6.
When i now slide my cube and go from the phone screen to the mediahub screen it is ok, form the mediahub sceen to the 1ste app screen is ok, but form the 2° - 3° and 4° app screen i got the same pictures as form the 1ste app.
I look at the values in the Cube and i notice that in Cube 2 there is :
07 07 08 09 0A 0B 0C 0D
0A C8 C9 CA CB 18 19 1A
1B 1C 07
Since i copied Cube 3 - 4 and 5 with the same values as cube 2 the values are the same.
In my cube 6 (original cube 3) i have these values :
07 0D 0E 0F 10 11 12 01
0A C8 C9 CA CB 1D 1E 1F
20 21 0D
I have already figured out what the numbers 01 till 33 are (they are also in the same register and have values for moves of the cube)
I made new strings form 34 till 66 with the values for the moves of the other cubes.
I can't figure out what the other things will mean like 0A 0B 0C 0D
0A C8 C9 CA CB
Can someone help me to make my 6 cube slide with my new icons on it?
Thanks
Click to expand...
Click to collapse
Why don´t probe this program: http://ww2.fatattitude.com/software/...?view=download and see??
v1zca1n0 said:
Why don´t probe this program: http://ww2.fatattitude.com/software/...?view=download and see??
Click to expand...
Click to collapse
Can't seem to get it work on my cruise. I tried to shut down the MediaHubMini.exe with SKTools but don't really know if it worked.. (don't really know how this tool works).
I think i got is shut down, but when i start the touchsetting programma i get error message.
hefi said:
Can't seem to get it work on my cruise. I tried to shut down the MediaHubMini.exe with SKTools but don't really know if it worked.. (don't really know how this tool works).
I think i got is shut down, but when i start the touchsetting programma i get error message.
Click to expand...
Click to collapse
Use to work with no problem. Install in Main Memory instead SD and try. If you can work is very intuitive and you are going to see very fast how to change the Cube. Say me something
v1zca1n0 said:
Use to work with no problem. Install in Main Memory instead SD and try. If you can work is very intuitive and you are going to see very fast how to change the Cube. Say me something
Click to expand...
Click to collapse
I tried it a different ways but i can't get it work on my cruise. I also tried the manual installation but it won't work.
hefi said:
I tried it a different ways but i can't get it work on my cruise. I also tried the manual installation but it won't work.
Click to expand...
Click to collapse
Very strange I have already install and working and I have a Cruise with spanish ROM cocked by Christonge and download in this forum I will try your trick for 6 sides and, after, try to work with the program and I will tell my experience
v1zca1n0 said:
Very strange I have already install and working and I have a Cruise with spanish ROM cocked by Christonge and download in this forum I will try your trick for 6 sides and, after, try to work with the program and I will tell my experience
Click to expand...
Click to collapse
ok thanks, let me know....
How do you change the color from the text on the today screen, my appointments are in white on a white background.
In the registry go to HKLM\Software\Microsoft\Color\4. Change the value to "00 00 00 00" for black or "00 00 FF 00" for blue. I try more colors without problems. I use FF FF 80 00 for yellow. this is well seen for quite a light background (photo)
notice: modify this registry key with memaid was weird. I try then total commander and there was no problem.
Martikn said:
In the registry go to HKLM\Software\Microsoft\Color\4. Change the value to "00 00 00 00" for black or "00 00 FF 00" for blue. I try more colors without problems. I use FF FF 80 00 for yellow. this is well seen for quite a light background (photo)
notice: modify this registry key with memaid was weird. I try then total commander and there was no problem.
Click to expand...
Click to collapse
thanx I'm gonna try it out.
where i found colour codes ?
where i found colour codes ? for all colours ?
maid3n said:
where i found colour codes ? for all colours ?
Click to expand...
Click to collapse
Try this:
http://www.colorpicker.com/
Copy the color from the upper text box, remove # sign and add "00".
If you want to understand what it means you can take a look here:
http://web.njit.edu/~kevin/rgb.txt.html
http://cloford.com/resources/colours/500col.htm
The first three groups of numbers (00 00 00) are standing for RGB (red green blue) in hexadecimal.
where can I find the registery using TCM? Thanks in advance
I didn't found anywhere for the position fix for footprints camera for COM3 build, so I thought it would be usefull if I post the patched footcam.exe from Footcam v1.26.20162730.00.
What I've done is using IDA pro, search for the immediate value of 0x2EC (dec 748), there will be 3 of them, the hex code is BB 3F A0 E3, where BB X 4 = 748, change it to B7 3F A0 E3, B7 X 4 = 732 (0x2DC) which is the value we need, since the softkey bar is 68, every 0x2EC below few codes, there is a mov command to load 0x34, which is the height of taskbar, change it to 0x24 and everything fixed.
Enjoy!
In trying to adjust how long the the screen goes blank and how long before it locks, I must have messed up some settings in
/data/data/com.motorola.android.providers.settings/databases/settings.db
I am looking for values for entries 65-71
65
notification_led_voicemail_enabled
1
66
screen_lock
1
67
screen_off_timeout_max
-1
68
lock_pin_min_chars
4
71
lock_timer_max
1200000
(There is no 69 and 70 in my file)
Thread closed
thanks for the info