Database Users

help the wizard is dead after upgrading to new rom

hi all ..
I did flash my HTC wizard with new rom after finishing the install the device reboot and stacked on the boot screen then I tried to go to the boot screen but I couldn't , I tried to make hard rest but also I coudn't nothing is working even charing the device cant be made .
bye bye

Are you able to get to a multi-colored screen with numbers?

In case you don't know, to get to the bootloader screen hold down the camera button and press the power button.

now i got the same problem.
I updated the rom & now i have the multi-colored (red/green/blue/white) screen
with RUU - IPL 2.18 - SPL 2.18 - USB on it (Qtek 9100)
I downloaded the tools from Vippie in the thread "How to flash a new ROM to your Wizard... a little tutorial!" but those won't help...
anybody got any advice? I would like to install WM6...
thanks in advance!

big Problem elf0100

Hello,
Can't start my elf0100 (HTC Touch)
I can see smart mobility, that's all.
I tried to unlock it with an other article here.
(ELF-USPL - after that the device is down)
So i tried to flash some different ROMs on it, but nothing changed.
Any idea? - Maybe SPL ROM zone gone?
I searched a little bit in the forum, but i don't find a solution - too many answers - nothing helps (Hard-Reset, Softreset, Flashing...)

Help, please help

If u can enter the tri colour boot loader then try this link it may help
Recover HTC Touch from tricolors RUU boot-loader (Mtty)[ONLINE]
http://forum.xda-developers.com/showthread.php?t=347700

Thanks for this thread, i will try this, bootloader is no problem.

ipl/spl not shown in the bootup screen

dear friends,
i have just bought the htc p4350 and noticed that when i boot the the device it does not display anything i.e the ipl, spl , gsm etc
my question how should i flash the device with the cooked roms available here without bricking the device
thanking all in advance
thanks and regards
faizell

Are you looking for this info when you turn the device on (looking at the splash screens) or when you put the device in bootloader (tri-color) mode? As far as I know, the splash screens won't show any info, but if you put the device in bootloader mode (hold down camera button and soft-reset with reset hole) the IPL and SPL should show up. Not sure where else on the phone to get this information other than running the RUU.
And it's definitely a good idea to check those numbers out before HardSPLing.
faizeliza said:
dear friends,
i have just bought the htc p4350 and noticed that when i boot the the device it does not display anything i.e the ipl, spl , gsm etc
my question how should i flash the device with the cooked roms available here without bricking the device
thanking all in advance
thanks and regards
faizell
Click to expand...
Click to collapse

lennyjaxn
thanks so much i have the ipl and spl which shows 4.24
now i will get back to reading how to flash it
i had the imate kjam and whenever you soft reset the phone it would dispaly the ipl,spl etc on the splash screen hence i presumed that this also should apply for the 4350
thanks once again
regards
faizell

No problem! Glad I could give something back after the tons of help I've gotten from this place!
I can understand your confusion, for sure. I had another phone that showed that info on the splash screen as well.

Dead HTC Phoebus Juno Apply Hard SPL Diamond

Dear All,
Help Required,I m Trying To Load Hard SPL From Diamond.After Load My
HTC Juno is dead & Couldnot Start in Bootloader Mode.
Please Help Me To BootLoading Again.............................

I'm sorry, but I don't think it's possible. You're not supposed to use the HardSPL from one device to the other because it is meant for that specific device and only that specific device. You probably have bricked it.
The only thing you can try is to attempt to start the bootloader mode. Hold down the camera button while turning on the Juno and keep holding it after you've released the power button. If the 3 color bootloader screen comes up, you can flash the official T-Mobile ROM, but I don't think that's possible because you tried loading a Touch Diamond SPL onto it.

Thanx ND4SPD,
I Tried To Enter Bootloader Mode But Failed.
Any Advice will be appreciated.

you have to try JTAG mode

tramuyo,
Thanx For Reply.
What is JTAG? How I Use It? Please?????????????????

artemis dead when flashing cid unlock at 99%

am using artemis p3300 but when i flashing uspl at 99% it shows upgrade failure now pda will be dead i cant go bootscreen too is any solution to back to boot screen? help me

Hi,
what do you mean by bootscreen? Windows boot screen or Artemis' bootloader (tri-color screen)? First of all I would try a hard reset, here's how to: http://wiki.xda-developers.com/index.php?pagename=Artemis_Resets
Did you try to flash USPL with this? http://forum.xda-developers.com/showthread.php?t=311403
You should at least be able to enter bootloader..here's an interesting thread:
http://forum.xda-developers.com/showthread.php?t=306904 .
Sorry I can't help more, i never experienced a similiar problem but I'm really curious to see it solved, waiting for some guru to help

sorry sir if i put battery inside pda will be start heating i cant switch to tri colour bootscreen havent money to buy a another pda am going to mad and am a looser.

Use MTTY to reset flash, the install the official rom for your device.

device never switched on is there any way to switching power on my device htc artemis p3300

bricked artemis goes mtty to reset the flash please give link here
how can i mtty to reset my bricked artemis please give me the link to download the file.