Related
have upgraded my Wallaby radio stack from original to 6.25 using .EXE file. My device restarted , but nothing happen just the boot screen. is there anything I can do ??
There are only G and U letter un right corner.
I can go to the boot loader (GSM error --> failed to start)
What can i do to go to today screen and reflash an other radio stack (like 4.21) ?
Qtek 1010 - 64M - ROM 3.04 ENG (WM2003SE) -
RAdio Stack depends on the Model. Check your rear sticker. It it´s a PW10Bx-model it uses 900/1900 MHz and require a 6.xx Radio stack.
If it is a PW10Ax then you have to use a 4.xx Radio stack.
Try this:
http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError
Stefan
thks
but i can't access to the device (install the good radio stack).
the splash screen freeze (with G an du lettre in place of the version of the radio stack).
Many hard reset, many test ...
if i can go to the today screen i can flash the good radio stack.
Have you tried installing the Special Edition ROM?
Still getting no Today Screen ?
Stefan
i cant get to today screen
All is working fine now.
1 : remove the sim card from the device
2 : go to the boot loader and test the phone (failed for all)
3 : hard reset
4 : wait 20 minutes
5 : you've got the to day screen and you can reflash the RSU (do not put the .exe file in the windows/startup)
and that all for me
I can't get to today screen....
irsan_donald said:
I can't get to today screen....
Click to expand...
Click to collapse
I have the same problem with my wallaby.. It shows splash but wont continue for a long time (more than 30minutes) I try to dowgrade ROM back to original Tmobile ROM wiwt 2002windows but still wont display today screen..
so i try to uprgrade to win 2003se and after 18 minutes today screen shows up.. I am lucky man now.. my wallaby its working again THANX GOD and U BOYS I LOVE U ALL !!!!
http://forum.xda-developers.com/viewtopic.php?p=138920#138920
ive just done it
HOPE THIS HELPS YOU.
Hi...
I upgraded my qtek 9100 from OS version 1.6.7.1 to cingular 1.8.11.1
The problem is that now, the phone doesn't start... the splashscreen appeears, along with... IPL 2.17
SPL 2.21
GSM 02.07.10
OS 1.8.11.1
But doesn't get out from there...
Did a do anything wrong?
PLEASE help me?
Is there any solution or is it bye bye qtek?
maybe you flashed broken or wrong rom.
start your device in bootloader mode (look in wiki how to do this) and then reflash again and if this does not work, get rom from your provider and reflash with this.
...
But my pda starts and it stays in splashscreen... is it repareble anyway?
Yes it should be fixable
Cant understand why you would want a old cingular rom (the cingular is not exactly same hardware as your phone wiza200 vc wiza100!)
You should download an aku2 rom here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
user name xda password xda
Next get into the bootloader screen - turn device off and start with camera button pressed - should be a multicolor screen
Next attach device to pc via usb cable
Flash with above rom and all should be well
Artemis and PDAMobiz_Dopod_P800W_AKU301_v1.1.2_PowerMap
i tried to upgrade my o2 arte200,i waited 30min. but installation frozen.
i did reset but after reset my phone stucked at bootscreen
IPL : 1.25.0001
SPL: 1.25.0000
GSM : 02.67.90
OS : 1.28.0.0
Please help... i tried hard reset and soft reset ... but no way...
when i plug usb cable activeSync dont recognise phone
same problem here,
help needed in advance
Active sync is usable only with Windows booted device. If Windows isn't able to boot, you must enter into bootloader, plug usb cable and then start rom flashing.
hi sir
i entered bootloader screen,connected usb cable ... (i can connect using mtty)
i run the software "CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE"
but gets an error message " cant connect to the phone"
WHY ???
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE
is a Rom for the Wizard not for the Artemis.
You need the original ROM so you have to search for the O2 ARTE200 ROM. The language of the ROM has to be correct as well.
how do you get the phone into the bootloader?
Tha said:
how do you get the phone into the bootloader?
Click to expand...
Click to collapse
Press and hold the record button and then do a reset.
no it doesn't work
My DOPOD was in the same trouble. I got the same vender ID error. Does anyone know where to get the original DOPOD P800 chinese ROM?
The same problem has I also.
My ROM upgrade ended bad. Test of installing of different ( I have already them probably 12) the INVALID ends VENDOR ID
I it can not now to remove CID nor to find out what it has it CID HTC__001 does not it fit. T - MOB 005 does not it fit.
I look for original romu from Dngaard ( DK)
Someone knows what CID maybe it is in HTC 3300. I have HTC P3300 is distributed would to Dangaard.
Where from him download
I greet
Irek ( POLAND)
im having the same problem on the o2 orbit ( need a orignal rom
upgrading
hai i am stuck in o2 orbit flashing in bootloader mode
help needed urgent
i got it working after i found the original german rom...loaded the orbit into the bootloader screen with 3 colors....plugged in the usb cable..then ran the german rom, after a few mins it reset and the orbit loaded up...after that i followed these steps to get it into english
http://forum.xda-developers.com/showthread.php?t=290241
flashed it with the tmobileuk 1.13 shipped file. everything is ok now.
cbprod said:
i got it working after i found the original german rom....
Click to expand...
Click to collapse
Where do you find the orginal rom?
Please help us!
send me a pm with your email, i'll send it to you
got mine back from the repair center friday.
no cost at all, fixed
route said:
finally i did connection ...
but goes %3 and gives error message
ERROR 294 INVALID VENDER ID
this update utility cannot be used for your PDA Phone.Please check your update utility ??????
Click to expand...
Click to collapse
could you tell me how did you manage to conect your phone? i have the same problem and i can't get my palm recognized by windows...
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
xister said:
you must go into the bootloader.
i´ve found the orginal o2 rom and now it´s working fine with wm5.
i wait for the o2 official wm6 update (i read something about may).
Click to expand...
Click to collapse
is that the o2 UK rom or the German one
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck
Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.
My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?
alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(
help me to break & solve this problem, maybe can also help the other members..
I tried to upgrade my XDA to WM2003SE everything goes right,
bootloader first time i still use v5.22
but when I soft reboot it freezes on the OZUP screen and
message ONLY FOR MICROSOFT bla bla bla....
i get this ROM from http://www.romkitchen.de/ ==> WM2003SE
then downgrade bootloader from v5.22 to v5.15,
using MMC (flash SD) continue to special rom 1.2,
and then cooked again using PC2002 by my own creation based from
romkitchen, what i want to ask is :
i cannot connect again via dekstop activesyn if i want to change
my ROM because my cradle cannot detect my charger?? but if i charge
directly, its work. What is the problem?
is my cradle/dekstop broken at the charger socket?
so what i need to do? just change the wire or socket or
i use the step like at http://wiki.xda-developers.com/index.php?pagename=WallabyCradleMod
if i prefer use the 2nd method, is that really OK? so just used cradle/deskstop, no need
power charger again if i want to change ROM to WM2003SE, because only can use via activesync?
after i change bootloader to v5.15, keep trying to change but only can via Flash SD Card,
i change to WM 2003 final, still same problem....after finish, only screen cannot enter the
menu or else, only boot screen until i am waiting for 15 minutes??? then change again to
WM2003 but using from http://www.romkitchen.de/tools, still same again....boot screen again...
haiyaaaa.....what happen?? i dont know, tired, always overtime to do this,hehehhee...
all my friends, help me...need your advice ^_^V
*now, i still used ROM from PC 2002,cooked again using PC2002 by my own creation based from romkitchen.
bootloader v5.15
Microsoft Pocket PC --> PC2002
Version 3.0.12039 (Build 11178)
ROM version : 3.17.03 ENG
ROM date : 05/15/03
Radio version : 6.24.00
Protocol version : 324e4
Model No.: PW10A1
I can not really help you, but i was also in the same situation, that i have had a device, that doesn´t work with any other ROM than PPC2002
Flashed several WM2003 ans the WM2003SE but non of them worked.
So i rest at PPC2002
Stefan
ow ow...
auch.. ok, thanks for the comment, i give-up,hehehe..but only for now,
take a rest first but i dont know for t'mrow, actually from 10 flashed,
i got 1 success, can got WM2003SE but with almost empty battery,
i know the inside and already set all, including i notice bluetooth icon,hehehe..
but how? i wonder that my sx56 with fake bluetooth, only icon
but after i charge my sx56 then i soft reset, its gone, back again with only boot-screen, after that, i can't find again WM2003SE ROM only lock with boot-screen, and ONLY FOR MICROSOFT..blablabla...
and about for my cradle/dekstop? how is it? can u give me solution to fixed it??
btw,thanks for helping, tips & trick hehehe...
i will keep trying to find/solved this problem by my own way ^_^V
modify my cradle/dekstop success
its working, i try to modify my cradle/dekstop with that steps (look at the top this thread), and it's work...actually not me who did it, but my friend,hehehehe....i ask his help and he agrre to doit, but all the risk is still at me, now i can charge and also syncronized to my notebook