Database Users

Headset bonding problem: Cannot reconnect after turning off

Hey Guys,
I'm trying to setup my Jabra BT250 on the XDA2 with imate rom 1.72. After bonding, everything works perfectly; However, if I turn off the phone's bluetooth or turn off the headset, I can no longer use the headset.
I have to go through the whole bonding process again before I can use the headset once more.
I have also tried Pocket Bluetooth Tools with the same exact results.
Not sure what is going on.

Found a workaround... All you need to do is click on the Bluetooth Icon, then click on the Bonded Devices tab then close that window. It'll enable you to use the headset again.
But I hope it's only a temporary fix and that someone has a permanent fix out there.

Hey...I also go thru the tedious task of clicking icons to on/off the bT headset.
Enter PocketZenPhone...
It save you the trouble of doing this...
I'm sure you'll find the thread and dicussions on the active thread on the homepage. Its cool. 8)

Thanks... I notice that it works fine if you give it a few seconds before trying to answer.
I need to do more testing

Activesync - Bluetooth Help needed

Can you setup you phone and pc to automatically start syncing when you get into the BT range? I have a Imate Jam with a cellink 6030 100m BT v2.0 dongle.
If I walk away out of the range, it disconnects, but doesn't re-connect when I am back in range. Don't want to switch my phone on everytime and open up activesync and then click on sync over BT to get everything going again.

ActiveSync and Bluetooth hassle

I've got the latest iMate rom with the push email installed on my Vario. Have started to notice that after disconnecting from either ActiveSync or Bluetooth that my Vario requires a soft reset to receive and make calls or to access the Internet or download email via gprs.
Anyone else had this problem?

active sync via bluetooth
I have latest ROM and since that no longer can connect to active sync which I was able to before. I am able to connect to my car and headset.
I'd love steps--It doesn't give me active sync as a choice when I try to connect to computer from 8125 active sync using bluetooth. Only service listed is WIRELESS STEREO.
anythoughts would be appreciated

InternetSharing over USB AND BT on PPC activated

Hi Everybody!
Looking around for a soulution to BT PAN with Toshiba BT Stack on my Dell I played a while with the USB connection.
I'm using TomTom with BT GPS quite often the same time I'm online, so I tried to disable BT on PPC, Internet Sharing with USB, IP assigned, online - then reactivated BT and it works great both together - even phone calls meanwhile connected via UMTS to the internet.
So, using the build in function in WinXP and set up alternative options for your IP/DNS/etc works even (takes 3 - 5 seconds more to obtain IP) fine.
So no need any more to deactivate BT on the PCC before using internet.
Regards,
Alex

Simultaneous connection of more than one BT device

I got my i8000 two days ago. I've got two BT related challenges.
1. Running the stock ROM, I've had a BT watch (SmartWatchM sw)connected and paired with it. Then I wanted to pair my Plantronics 645 headset with it as well. The BT manager shows both units, but as I paired the headset, the phone disconnected the watch.
2. I walked out of range with my BT headset. It disconnected. As I came back I expected the phone and headset to be paired again automatically. This did not happen. Now both the watch and the phone show up as disconnected in the BT manager.
For 1. a) To have both connected simultaneously I figure I need to add another com port. Is this correct?
For b ) I cannot find the step-by-step instructions on how to do that in the user manual nor in the advanced user guide. Anyone knows the steps?
For 2. What do I need to do to make the two units re-pair without having to go through the whole pairing procedure?
Thanks!