Hey Guys,
I'm trying to setup my Jabra BT250 on the XDA2 with imate rom 1.72. After bonding, everything works perfectly; However, if I turn off the phone's bluetooth or turn off the headset, I can no longer use the headset.
I have to go through the whole bonding process again before I can use the headset once more.
I have also tried Pocket Bluetooth Tools with the same exact results.
Not sure what is going on.
Found a workaround... All you need to do is click on the Bluetooth Icon, then click on the Bonded Devices tab then close that window. It'll enable you to use the headset again.
But I hope it's only a temporary fix and that someone has a permanent fix out there.
Hey...I also go thru the tedious task of clicking icons to on/off the bT headset.
Enter PocketZenPhone...
It save you the trouble of doing this...
I'm sure you'll find the thread and dicussions on the active thread on the homepage. Its cool. 8)
Thanks... I notice that it works fine if you give it a few seconds before trying to answer.
I need to do more testing
Related
Hi,
i noticed everytime i turn off bluetooth (in order to spare battery time) it reactivate itself alone after a call... is this normal ? does anybody else experience this problem ?
(ps : i have pocket bluetooth tools, but i don't think that s the problem... is it??)
Thanks for any help
It is, and its not a bug, its a feature Its so you can answer a call using your bluetooth headset.
If you dont have a headset its obviously useless to you, but PBT is not under development any more, so you kind of stuck with the way it works now, or to un-install it.
Surur
Ok. i just had to read in fact the guide http://www.bluetooth.jazztel.es/guide_e.html to see that it can turn it back to off if BT is not used after 60 seconds...that s a good idea
Too pity they stopped development, it helped me a lot in the set up of the BT for activesync via BT and for set up of BT GPS...
anyway, thanks for the hint. (it gave me the idea to look a little bit further
Have a nice day!
I use PBT and I use the 60 second feature. What I found with my o2 clip bt headset is that the headset seems to lose connection to the phone after a short while regardless of the 60sec rule. Sometimes it would happen just before receiving or dialing a number.
Very annoying.
Cheers
Anthony
I had a |Plantronics bluetooth headset which connected as soon as it was turned on. I now have an iTech S35 Bluetooth stereo headset. This won't automatically connect. I have to go through all the menus to select as wireless stereo and handsfree - a total of 9 taps!
Not sure if this is the fault of my device or the headset.
Anyone know how to get them to connect automatically?
happens to me too although i have different make of headsets... dunno the cause either what i do is delete the partnerships and reestablish them. I do this everytime I get the iffy behavior. so it's no big deal.
I have the same problem with my jabra BT620s headset. It connects it self as a Bluetooth handsfree and can use voice dialing, but It doesn't connect automatically as a wireless headset. I have to go to Wireless Manager and set it there...
Any way to make it automatically... or at least with a use of a simple click?
hmmm... known issue on the BT620s, however the fact that the iTech clip is also affected is new to me. Quite frankly, I'd never asked.
There are several headsets that don't have the issue, but its about 50/50.
I've been having a similar problem with Lubix NC1s (btw, had the problem on my MDA too).
Until I know a permanent fix, I've used iLauncher to place a Bluetooth icon on the System Tray, so at least I can get to the device profile in 2 clicks.
rpodos said:
I've been having a similar problem with Lubix NC1s (btw, had the problem on my MDA too).
Until I know a permanent fix, I've used iLauncher to place a Bluetooth icon on the System Tray, so at least I can get to the device profile in 2 clicks.
Click to expand...
Click to collapse
How did you get to the shortcut - I couldnt find which programme / file to select?
SHC said:
How did you get to the shortcut - I couldnt find which programme / file to select?
Click to expand...
Click to collapse
This is using iLauncher from SBSH:
Under Settings>Shortcuts you can select "* Shell Tray Tab *" as your tab, then "Add" Bluetooth from "Cpl Applets".
One click opens Bluetooth Settings, then click on Devices.
Ah Ha! Done it, Thank you.
I often wondered how you got shortcuts on the bottom tray!
thanks
With the iTech you have to press the MFB buttton (the flashy one) once it is turned on to connect it. Bloody stupid I know. I don't turn it on to watch the light flash, I turn it on to connect it to my device.
Hi-I tried this with a trinity and itech and a single press of the button just activates voice dial then disconnects. Any ideas?
Sorry just re-read, I have an R35, thought you did too. You could try the Bluetooth audio routing program from below, there's a program & a separate today screen plugin version:
http://www.trianglepowers.com/ppc6700/
Not sure if it'll work or what the quality may be like but its worth a stab.
instructions with Bluetooth X5
For those that have a Tytn and Blueant X5 (with the latest firmware)
- turn on bluetooth on tytn and the X5
- quick-press volume up and down buttons -> Done (you might have to have your bluetooth in discoverable mode -> not sure)
BTW - Blueant X5 are fantastic - I have had it for over a year; and now about 5 of my work colleagues bought them too.
daedalia said:
With the iTech you have to press the MFB buttton (the flashy one) once it is turned on to connect it. Bloody stupid I know. I don't turn it on to watch the light flash, I turn it on to connect it to my device.
Click to expand...
Click to collapse
I have an iTech S38 and it works the same with the MFB button. If it does not work for you (ie when you press it you just get voice command) then I think it's a rom issue, not the headset itself. Ie, the bluetooth stack is not recognising the request to connect from the headset.
Try A2DPToggle
http://www.teksoftco.com/index.php?section=freeware
Can also be made to work with one button press using mortscript.
Surur
Hello,
I have been reading extensively this extremely useful forum to tweak and set up my newly acquired Kaiser but I now face a problem:
I own a Creative CB8100 Stereo headset (without hand-free) and I am trying to have it connect automatically to my Kaiser.
The only way I managed to connect the two together is, in the Bluetooth settings on the Kaiser, by tapping on the headset name (CB8100) and choosing "Set as a stereo headset". This is quite a long procedure and I would like to know if there is a way for this headset to connect automatically once turned on. In the worst case, is there a shortcut I could put on the Today screen to manually connect to my headset?
Thanks,
Bhangraman
Nobody got any idea on how to simplify this process?
A thread in one of the other forums suggests that making your Kaiser discoverable may help. Give it a try.
I am afraid it made no difference
Could you please link me this other thread you are talking about?
Here's the thread.
Thanks a lot
Installing A2DPToggle which provides an on/off button on the home page solved my problem.
i have a bluetooth headset and my mda wont find it but i can find it on my outher phone
Assuming you tried obvious like turning on bluetooth, have to checked to make sure the bluetooth services are being loading? I use sktools to see my startup processes and services. Check that out and maybe one of the bluetooth services is set to disabled.
Those are my only suggestions. I am very new to the use of bluetooth.
Jeff
It's also quite possible that your headset is just not compatible with a wizard. There's more than one bluetooth driver, and not all phones carry all drivers. It might be an easy fix if you can find the missing driver.
What's your headset brand/model/etc.?
thanks i got it the bluetooth was "slaved" to my outher phone all i hade to do was hold power button for abot 30 sec. and it reset so i could find it thanks for yalls help
Hello,
i have the same prop like many other Leo Owners. I set Audio over Bluetooth, first time it works, after shut down the sound comes via the Phonespeaker no more chance anymore to change it. Except after hardreset but than the same, it works so long you dont shut down the phone.
Same Prop with Voice Command, Cyberon, Vito the sound goes over the Systemspeaker, i had read all Threads no solution works.
I have the origin newest Vodafone German Rom 1.66 are there any knowing reghacks to fix it.
Thank's a lot Ingo
Have you tried going to the settings > Bluetooth and activate stereo audio there?
When you first link your bluetooth headset and your phone, it automatically connects both, but after you power down either bluetooth connection or the headset, you have to manually connect the stereo autio.
re
i have only a point where i can set play systemsounds on the bluetooth device or remote device and this is always activated.
re
The same with this post:
Spizella said:
Maybe?
I didn't made any test!!!
[HKEY_LOCAL_MACHINE\Software\Microsoft\Bluetooth\AudioGateway]
"BTAGExtModule"="OEMAGW.dll"
"Capability"=dword:65
"ConnectHFOnCall"=dword:1
Used this CAB, now the button is working. Only one step is missing
http://forum.xda-developers.com/showpost.php?p=1282191&postcount=28
Voice command accepts voice commands on the phone after long hold on headset button! Anyone get this to announce over their bluetooth headset please let us know how you did it or if there is another version out there please post a link.
Click to expand...
Click to collapse
it's absolut mystery first time after install it works. closed bluetooth or shutdown the device thereafter no more like all other over the speaker not over the headset.
see my post: http://forum.xda-developers.com/showthread.php?t=671015