Related
i dont know what happened ?
it was working fine i picked it up and it was off... and now it wont turn on..
What happened?..
boinger66 said:
i dont know what happened ?
it was working fine i picked it up and it was off... and now it wont turn on..
Click to expand...
Click to collapse
WTF??!!? Have you made the usual hard reset, battery out, put it into Bootloader mode, reflashed or anything like it?
Doesn't sound good. I'll find you on IM.
Do u charge it ?
Do u see a led ?
xmen06 said:
Do u charge it ?
Do u see a led ?
Click to expand...
Click to collapse
i do...
also it was really hot when i picked it up
EDIT: just fixed it... seems the battery got ultra drained somehow ... went from 90% - 0 in 30 min... i dont know why that happened
that's wierd...Mine would not turn on yesterday. It just had a blank screen with the Green light on around the joystick (like it was fully charged). So I soft reset and nothing, still green light and blank screen. So set it to bootloader mode and ran mtty to check it out, Mtty tests were normal and nothing seemed wrong, tried reset, check for bad blocks, and the normal info and task commands, everything looked normal, but it would not boot up...took out the battery and waited 10 minutes, still green light and blank screen. Charged battery still same issues
SO I tried to hard reset...still same thing,, it asked to confirm hard reset, looked like it did hard reset, but still same problem..
SO I finally, put it in bootloader, reloaded the wm6 HTC__001 rom and it worked fine, Restored from backup and I was back to normal...But I was starting to get a little scared that some how my advantage was bricked...
Haven't had any problems since....Wierd
plz helpurgent
can sum1 plz tell me how to hard reset ameo or how to put in bootloader mode..
thanx in advance
hubmobile said:
can sum1 plz tell me how to hard reset ameo or how to put in bootloader mode..
thanx in advance
Click to expand...
Click to collapse
There are two main methods:
1. Try using the search function.
2. Read the wiki.
Try either of these and you will suceed. Ask without doing either and you will become unpopular!
boinger66 said:
i dont know what happened ?
it was working fine i picked it up and it was off... and now it wont turn on..
Click to expand...
Click to collapse
the device powers itself off if the battery overheats.
take it out and leave it for a bit
same problem here
same here, after doing Olipro's AthenaUnlocker step 1 and went to Bootloader mode to check spl version. my device is stuck to its bootloader mode & when i soft reset the only thing that will turn on is the led light of the joystick. is there a way to bring it back to normal mode from bootloader mode?
thanks in advace!
rvnteck said:
same here, after doing Olipro's AthenaUnlocker step 1 and went to Bootloader mode to check spl version. my device is stuck to its bootloader mode & when i soft reset the only thing that will turn on is the led light of the joystick. is there a way to bring it back to normal mode from bootloader mode?
thanks in advace!
Click to expand...
Click to collapse
Have you removed the mini sd?
unfortunately no
Even hard reset cant fix it, i guess im down to flashing it to the x7501 rom. i hope this works
- My Ameo after auto turn off (I set 1 min) it can not wakeup when I press ON/OFF button, all light is OK (flash), OFF sound is heared when a incomming call.
- I must soft reset it for resuming again
What is wrong ???
Help me please.
Thanks..
boinger66 said:
i do...
also it was really hot when i picked it up
EDIT: just fixed it... seems the battery got ultra drained somehow ... went from 90% - 0 in 30 min... i dont know why that happened
Click to expand...
Click to collapse
Nice panic there! LOL
;-p
vios5689 said:
- My Ameo after auto turn off (I set 1 min) it can not wakeup when I press ON/OFF button, all light is OK (flash), OFF sound is heared when a incomming call.
- I must soft reset it for resuming again
What is wrong ???
Help me please.
Thanks..
Click to expand...
Click to collapse
Typically this is caused by some software running in the back ground. Try to disable anything from running and then re-enable one thing at a time and see if you can isolate the problem. Sometimes it's two programs conflicting with each other so you may have to do some experimentation here. Hope this helps.
eagle 1 said:
that's wierd...Mine would not turn on yesterday. It just had a blank screen with the Green light on around the joystick (like it was fully charged). So I soft reset and nothing, still green light and blank screen. So set it to bootloader mode and ran mtty to check it out, Mtty tests were normal and nothing seemed wrong, tried reset, check for bad blocks, and the normal info and task commands, everything looked normal, but it would not boot up...took out the battery and waited 10 minutes, still green light and blank screen. Charged battery still same issues
SO I tried to hard reset...still same thing,, it asked to confirm hard reset, looked like it did hard reset, but still same problem..
SO I finally, put it in bootloader, reloaded the wm6 HTC__001 rom and it worked fine, Restored from backup and I was back to normal...But I was starting to get a little scared that some how my advantage was bricked...
Haven't had any problems since....Wierd
Click to expand...
Click to collapse
That is weird and scary. Did you try to remove the battery then plug the device into the power source with the battery out also?
rvnteck said:
same here, after doing Olipro's AthenaUnlocker step 1 and went to Bootloader mode to check spl version. my device is stuck to its bootloader mode & when i soft reset the only thing that will turn on is the led light of the joystick. is there a way to bring it back to normal mode from bootloader mode?
thanks in advace!
Click to expand...
Click to collapse
Yes, something about flashing a specific version to your device but since this never happened to me i don't have details. Feel free to search the threads....i know it's somewhere at the top. Have fun!
boinger66 said:
i do...
also it was really hot when i picked it up
EDIT: just fixed it... seems the battery got ultra drained somehow ... went from 90% - 0 in 30 min... i dont know why that happened
Click to expand...
Click to collapse
I had my ameo also drawing 1,5A from the battery (actually powerdrain was higher than charge current) Never found out why.
Before I start I know how touchy people are about searching forums and the wiki etc... but I already have!
Ok so, I tried to flash a new ROM to my phone last night, I have done it before without problems however this time I was having trouble getting the phone to connect to my laptop (I run Windows 7). Both USPL and HSPL wouldn't work (in fact active sync wouldn't even recognise it).
So I went to bed, woke up and... My phone didn't work at all
I spent ages trying to get it too work, I tried putting it into bootloader, but nothing happened, I tried getting it to Hard reset, but nothing happened. (By nothing happens i mean the screen doesn't turn on).
The only sign of life i get from it is the little vibration that usually occurs after the 'smart mobility' screen appears. Except this is delayed by about 10 seconds from after pressing the Power button.
The delay makes me think that there is something else wrong with the phone other then the screen...
Please help!!
Oh and I am sorry for the essay... I only just realised how long and rambling it is haaa.
UPDATE: right it just connected to activesync but still nothing on the screen, is there any way of checking for definite that the screen is broke before I fork out for a new one? There is astill the massive delay between turning the phone on and getting the little vibration...
Try removing battery overnight, then re-inserting. Then try to get to bootloader or hard reset
how exactly did you manage to brick it? did you flash the rom in question with uspl, or do u generally have hard spl installed? i dont know but it looks like the bootloader is somehow broken ...
Ok I will try doing that, thank you for helping
And no, I didnt get as far as flashing the ROM because active sync never recognised the phone in Bootlaoder. I usually use USPL.
Did you fix it? and if so how?
I have very similar issues with my HD right now. Screen went black, bought a new LCD and still the same problem. Oddly enough the only way I can get the screen to come on is to take the battery out and set both battery and phone body in my window sill for half an hour or so. It is cold here right now and they are both pretty cool to the touch when I take them out. Put it back together and tada! Screen comes on. I dunno what the deal is also, don't know if its the battery or phone being cold that makes it work again??? I am going to try and figure it out.. Try it on yours it may help
I have just got the HD2 and been using it for a few weeks. Downloaded a few apps (eg HTC rom, BSB tweeks) and all is good. Saw Max Manila and looked like a great idea - checked my manila version 2.5.19211619.0 and downloaded 2.7 SE (checked it's right for my manila) loaded onto phone and it crashed after soft reset. Took battery out and phone doesn't go past first screen (with the red writing bottom left) - Hard reset is the same and now I'm worried!
Any ideas???
sad to say yy sounds like hard reset time.
power off, hold volume up and volume down, tap power keeping volume up and down pressed til the screen comes on and follow the prompts.
it will reset your phone to factory defaults.
never used max manila so I cant help with what the problem might be, but if there is a developers thread for it you might be better asking there.
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
if your phone is provider locked then that will not work.you need the rom that came on your phone. so if was from uk o2 then you need the o2 uk rom, otherwise it wont work.
No luck! Whilst I've got everything to sort the phone out it won't do anything but load the white first screen no matter which buttons I hold down.
Man this sucks!
Guess there's nothing for it except the bin unless anyone else has any other ideas??
can you get into boot loader?
press and hold vol down(not up this time, just down) tap and release power, keep vol down held. should boot to striped cultures colored screen.
if you can what does it say next to SPL?
Hi Samsamual
Thanks for helping but no, won't go into bootloader either - doesn't respond to any input (even when I conect the usb the charge led doesn't come on!) and just starts with the white screen with the HTC logo and then the red writting appears and it just hangs - left it for 5 mins just to be sure and no change
Looks like I've really messed it up although I have no idea what I did wrong - instal went just like the other things I installed.
Ahh shame. All i can suggest is the original rom sd card method. But it MUST be the propper rom that came on your phone, so if you got it from vodaphone, , , even if it is unlocked, you must use the voda rom.
Also, have a really good read through the pages in teh rom development section. If you can find someone with the exact same issue, you could be one step closer to fixing it.
Brotherskid said:
Thanks for replying samsamuel - I've tried the hard reset and it doesn't work!
Even when I do as you say, I get the white start screen with htc written on it and then several red lines at the bottom right starting R G and D and that's it! It just stay's like that - At this moment I'd pray for a hard reset!!
I'm going to try booting from the sd card but I'm not sure I can get the phone to go into the bootable mode. I've downloaded the HTC rom and extracted the nmh so we'll see.
Click to expand...
Click to collapse
you must tab the power botton for a short time just tab it and leave it with keeping pressing on the volume up and down buttons don't leave them i think it must work with you tell me if it works
Brotherskid said:
...I'm going to try booting from the sd card b
Click to expand...
Click to collapse
When you tried the SD card method did you use a 2GB SD card and was it formatted to FAT32?
WB
Have you tried a boot (all combinations!) without the sd card installed?
Hoss and WB - thanks for the comments
Hoss, I've held the volume buttons for over a minute after powering on - no change
WB, I can't get the phone to go into boot loader screen but thanks for the info for the future. Next time I'll see if I can copy the original rom just in case.
Resigned myself to having a new paper weight on my desk and looking for a new phone - Guess I won't be putting so many programs on my new one....
PA - Thanks for the advice - Yes tried with sd card in/out sim in/out bootloader, hard reset, soft reset and always the same.
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
rlydiard said:
In your posts you do not mention where you bought your HD2, and I do not know what country you are in.
From what I have read, it seems that you did not flash any ROMs, nor change your SPL, so if I were you, at this point, rather than accepting a bricked paperweight, why not explore your warranty possibilities?
Contact the place you bought the HD2 (the dealer) and explore your options. Since I do not know which country you are in I will not suggest an HTC service center, but if your country has such a center, at last resort, you might check out that possibility.
Since you apparently had no hardware problems before the manila incident, it would seem that it is a software glitch somehwere.
Good luck with all of this. It must be almost heartbreaking to have this happen with such beautiful hardware.
Click to expand...
Click to collapse
What's most annoying is it wasn't as if I was doing anything crazy! Max manila is used by many people (from what I've seen in the threads) and I guess I downloaded the wrong one (although naturally I checked and it's the right one). Certainly will curb my using of 3rd party software! As for the warranty, you're right, I can try and see if it can be fixed (bizarrely, that hadn't occured to me - I thought that with no resets working HTC couldn't do anything). Thanks for the tip and I'll let you know how I get on.
Surely your warranty will cover this. Yes, let me (and us) know how all of this goes. You will get your phone back to what you deserve, for sure!
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
watnuweer said:
I had the same issue.
Sent mine to HTC and got it back with the comment "Cannot reproduce"
Probably it solved itself when the battery was removed for a couple of days in the mail.
It has now been working for two weeks again.
Fingers crossed.
Click to expand...
Click to collapse
Experential nut I may be, but just wondering if you had the problem after you installed the MAx manila? I wonder now what versions of OS may be causing this problem.
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
fakker said:
i had something like this with my HTC Diamond... It stopped responding completely when turned on, didn't respond to the usb cable being plugged in (the round ring used to illuminate when charging)
I took the battery out, for about 30 minutes... then left it charging for another 30 minutes - booted up straight away and never did anything like that again
Worth a shot just leaving it without power for awhile, and then just recharging it
Like watnuweer mentioned, "cannot reproduce" probably fixed itself by not having the battery left in for awhile
Click to expand...
Click to collapse
This is getting more interesting, what do you suppose is the cure of taking out the battery, and then charging? I do not doubt your experience, I am just extremely curious if anyone can explain this phenomena.
Cero92 said:
Hi all, i just got a Qtek 9090 with WM2003 (ITA). I upgraded to WM6.1, but now it has some strange problems: first of all, when it goes in standby, sometimes it doesn't wake up. If i have to reset it, most of times it doesn't boot (it shut down before WM loads) or i get R: None G: None and i have to reset again (otherwise the phone won't work).
The lock at the boot doesn't happen when the phone is connected at the USB port (i think that's because it charges, maybe it's a battery problem?)
Another thing is that i can't turn it off: if i hold pressed the power button, it deactivate the backlught but the device stays on, and if i make another long press, i get the backlight back again... I had this problem also with WM2003, maybe it's normal?
What do you think? Whan can i do?
Click to expand...
Click to collapse
Have you make a HardReset?
The correct HardReset, not only reset and press Power button!!!
See in my HowTo Section...
and why not WM6.5.5 see here
yep, hard reset is a good start, but about your other problems:
the device does not really turn off, like other phones. pressing the power button makes it go to hibernate, the display turns off, depending on your settings, it locks the hardware buttons and it shuts off wi-fi, it hardly uses any energy but gsm/gprs stay on.
the device seems to be off, yet the phone is one and you can be called. that is the closest you get to switching it off. when you turn on airplane mode, the battery consumption is even less so there is not really a need to turn it off.
pressing and holding the power button always was for the backlight. many other devices open up a shutdown menu when you do that, that would allow you to turn it off, soft reset, or switch off the backlight, but for the BA, that is not the standard. however, if i read it right, d-two is working on remapping the power button, probably for that cause.
the R: none G: none issue is known and not a problem with your phone, whenever you run out of power or remove the battery for a second, the next boot will be w/o radio (R and most roms don't allow booting without it. that's why you get stuck there and have to perform a soft reset. back in the days of wm2003 i used to remove the battery when the device froze to reset it w/o the stylus, because it didn't matter then. with cooked roms, it is different, just like the booting splash screen or the way to perform a hard reset, many things change on a cooked rom.
the issue with waking up from standby, or the SOD (standby of death) is an issue, that most likely has something to do with a backup, restored after flashing another os, or maybe you didn't perform a hard reset, as stated by d-two. you should do that, now that the device is still new, you have nothing to lose
also, read through the tutorials posted by d-two and myself, whether you missed anything while flashing.
The "real" hard reset is the one i can get by pressing camera + record button and reset? If so, i already did it after flash (i use d-two 6.1 Manila ROM in WWE)
It shows me 3 options, i put on YES "Clean Registry Hive" and "Format Storage" then i press the mail button, the screen become white for a while and the next boot al seems to be ok.
It seems, because after some time i get again the "standby of death" and, if i press the reset button, the most of time it won't boot up again (it turns off before i can get to WM), if it works phone doesn't. All these boot problem can be avoided by connecting the phone to the usb cradle, so maybe it's also a battery problem, i think...
@ d-two: i'll try your new ROM, however before i've tried your 6.1 ROM
I've already read your guide because i've got Windows 7 and i couldn't flash without your tutorial
NEWS: installed d-two new ROM, after flash i made the hard reset selecting the second and the third options, then i get the blank screen and, when viewing the htc screen, it shut down itself like it did before
As always, with the usb connected, it has no problem :\
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
n0rbi666 said:
It can be battery power - battery is old, and it doesn't provide current [A], or voltage drops [V] and phone think, it's empty.
Maybe you can try with new battery, or buy 2 nokia bl-4c batteries and repair orginal battery (somewhere on forum there is a tutorial about that - but use bl4c, not bl5c like in tutorial - bl5c are too thick to fit)
Click to expand...
Click to collapse
That's what i was thinking (and that's i hope it isn't)... Now with another recharge cycle it seems to be good also with cooked ROMs, i hope it's solved
Maybe you just have to charge/discharge it for 4-5 times, and it will restore it's capacity. Mine BA was turning off when battery indicator was showing ~60-70%, and now I'm waiting for new battery (i destroyed original )
"charge/discharge it for 4-5 times" does not have an effect on Li-ion kind of batteries. This is probably a software problem. When you turn your phone on (after removing a battery) it always shows "None" for R and G, so just press Reset button and it will be ok. I use Reset to power it on Then you can flash 6.5.5 which doesn't have problems, and do a hard reset. There should be no problem at all..
I also got the problem with the stock ROM :\
The R: None G: None error is the less important problem
Got any luck fixing it? I've had similar problems before, sometimes it turned itself off when the battery was at 60% in WM2003. Did you update to d-two's 6.5.5?
Yes, now i'm running d-two's 6.5.5 ROM.
No, i still had the problem Yesterday i called to the assistance service and they said me to remove the battery and after a while recharge it.
I put off the battery yesterday at 16 and i put it again in the phone this morning at 8, i charged it but i still have the problem
This evening i called again and they said me that i have to send it back, i'll flash the original ROM and send it on monday.
That's a shame, i really like this device, even if it's not mine, my sister uses it and she's not a pro user, what a waste
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
marko_serb said:
Didn't understand, what "assistance service"? This is very old phone, I just can't believe it has some kind of warranty
I have another battery, and using it the device turns it off sometimes while it's in the stand-by mode! Don't know why, the voltage on it is fine, I have measured it while working...
Click to expand...
Click to collapse
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Cero92 said:
I bought it on an eBay market and it offered 60 days warranty. It's not official HTC/Qtek warranty, but it doesn't make difference, as long as the device will work
If for you it happens only when it's in standby, maybe you just have the standby of death, the problem Chef Tony was talking about at post 3?
Click to expand...
Click to collapse
My Roms have no SOD
This is when vbase32 have all 01000000 base adress !!!
Search about SOD!!
No, this happens only with my old battery. I'll try it out now with this new ROM!
I was trying to understand his problem
Just to know, what kitchen do you use?
Cero92 said:
I was trying to understand his problem
Just to know, what kitchen do you use?
Click to expand...
Click to collapse
First i have create my own kitchen but then i have found the OSBuilder and this is the best kitchen ever
With this kitchen you can look the Vbase32 for SOD!!!
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Cero92 said:
Well, i trust you that your ROMs doesn't have SOD problem, in fact this happened to me also with the shipped WM2003 ROM, it's a real hardware issue
Click to expand...
Click to collapse
I think so, sorry
d-two said:
I think so, sorry
Click to expand...
Click to collapse
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Cero92 said:
No problem, i'll send it to the assistance on monday, i hope it won't take too much time :\
Click to expand...
Click to collapse
good luck But very cool that you have warranty
My frigin HD2 keeps freezing on me on the splash screen. How do I fix this? I'm running windows 6.5 and I can't seem to get past the splash screen. It's mocking me. Someone please help before I smash this thing.
flashed anything recently? do you get RGD info, small red txt, bottom left on splashscreen?
This is my fathers phone and I haven't flashed anything for him since I flashed the energy rom stable version. I get to the small red text and then it freezes and nothing happens.
try the factory reset, switch off - press the up and down volume keys together and hold them in - press the power button release the buttons when you get the white screen read and follow the instructions
johnerz said:
try the factory reset, switch off - press the up and down volume keys together and hold them in - press the power button release the buttons when you get the white screen read and follow the instructions
Click to expand...
Click to collapse
Thank you for the advice. I've tried this and I still get stuck with the opening splash screen. Anyone else?
Try booting the HD2 without te sim card or the SD card in, bit do it ome at a time so you can see of the sim card of SD card might be giving you a problem.
If no joy with that option, then put the HD2 in a sealable plastic bag and then in the freezer for 10 to 15 minutes then try to bootx it. If it boots then the device is more than likely experiencing hardware problems. So if the HD2 is still umder warranty flash the stock ROM and SPL back to the HD2 and send it in for repair or ecxhange.
Thanks everyone for the suggestions, it seemed to be a hardware problem. I sent it back to HTC and they repaired it for a small fee. Now I seem to be having problem with it reading sim cards so I'm not really too sure whats going on with that.
HI everyone it seems that i have the same problem now, i dont know if i should open a new thread. Anyways, i installed RiffleLock v14 and combined it with live wallpaper. I guess this was a "deadly" combination. My phone keeps on restarting . Even with hard reset using physical hardware. After i completed the whole process. When it starts, same problem arises, phone keeps on rebooting... can anyone help me on this?
Bought this phone just 2 weeks at ebay. It is an HTC HD2 Android (this is now the ROM inside phone memory) CM7 Typho0n 2.3.4... cant give you anymore info this is my first time to own a droid.
I already PMed a senior member, but any suggestions and help will be very much appreciated. Thanks!!!
earthworm1102 said:
HI everyone it seems that i have the same problem now, i dont know if i should open a new thread. Anyways, i installed RiffleLock v14 and combined it with live wallpaper. I guess this was a "deadly" combination. My phone keeps on restarting . Even with hard reset using physical hardware. After i completed the whole process. When it starts, same problem arises, phone keeps on rebooting... can anyone help me on this?
Bought this phone just 2 weeks at ebay. It is an HTC HD2 Android (this is now the ROM inside phone memory) CM7 Typho0n 2.3.4... cant give you anymore info this is my first time to own a droid.
I already PMed a senior member, but any suggestions and help will be very much appreciated. Thanks!!!
Click to expand...
Click to collapse
kutos for not starting a new thread! (btw what you describe for your android is called nand.)
my suggestion: start over. flash back to WM, then reinstall android on nand. takes ~15 minutes and will give you a clean start. otherwise, who knows what happened. or at the mininum, reflash your rom. or flash a new rom. but i like the WM option as you can see if is hardware or software as the culprit.
however, reboots can also be to bent battery pins.
"kutos for not starting a new thread! (btw what you describe for your android is called nand.)
my suggestion: start over. flash back to WM, then reinstall android on nand. takes ~15 minutes and will give you a clean start. otherwise, who knows what happened. or at the mininum, reflash your rom. or flash a new rom. but i like the WM option as you can see if is hardware or software as the culprit.
however, reboots can also be to bent battery pins"
Tried and checked that battery pins too! But actually it was the hard reset that baffles me. It takes like a second only, and it restarts. But when it do restarts it is like i did not do a hard reset. I like the advise you gave me, but the problem is i only had this phone for a little than 2 weeks. I cant even flash this coz it is stuck on bootscreen, I cant follow even tutorials on you tube coz it doesn't show that it was messed up like mine before they started flashing it. It's like a "Where do i begin Love Story song lol!!
I tried to contact the person who sold me this phone at ebay but he wont respond.
So what choices do i have here, i dont know how to flash with the current situation of my phone. Am even thinking of mailing this to anyone and giving me a dual boot then and just freakin pay and spend more over this phone. I dont have a choice.....
Any more suggestions here would be greatly appreciated.
hard reset ,nothin changed
i think we are talking about a couple of different things here (maybe).
when i say hard reset i mean - boot into bootloader (3 colored screen) - reboot holding volume key down - and via usb or sdcard flash back to windows mobile. have you done that? can you get to bootloader?
sucks you're having issues...
Yeah i can go to the 3 colored screen. That is actually the first i see before the "white screen"... can you teach me how to do that kind of hard reset??
I dont have WinMo anymore... the guy that sold me this phone put Android as the main OS.
earthworm1102 said:
But actually it was the hard reset that baffles me. It takes like a second only, and it restarts. But when it do restarts it is like i did not do a hard reset.
Click to expand...
Click to collapse
doing a hard reset when magldr/android is installed is pointless, because it doesnt reset anything, (or i think ive seen it said that it hard resets magldr, the effect is the same, , , nothing happens) which is why it only took a few seconds.
earthworm1102 said:
Yeah i can go to the 3 colored screen. That is actually the first i see before the "white screen"
Click to expand...
Click to collapse
still got a leoimg.nbh on your sd card? could explain the white screen,,,
when i say hard reset i mean - boot into bootloader (3 colored screen) - reboot holding volume key down - and via usb or sdcard flash back to windows mobile.
Click to expand...
Click to collapse
thats not a hard reset, thats flashing back to stock.
samsamuel said:
thats not a hard reset, thats flashing back to stock.
Click to expand...
Click to collapse
yep yep. tis what i meant.
@ the op, since you didn't put the rom on your phone, i would flash back to stock (aka back to windows mobile) and get rid of android. then put back android. see what happens.
read this thread, #5 to be exact to get back to windows mobile:
http://forum.xda-developers.com/showthread.php?t=893948
this will get rid of android, save your hspl which will make putting android back on easy. however, if the problem exists in wm, is out of my knowledge, and is not seemingly software and more likely hardware. but if samsamuel thinks different, he knows a ton, and has helped me out of many a pickle. cheers.
K bro. Thanks!! +1 thanks for you!!!!
@samsamuel am talking about the white screen wherein you will hard reset ( holding volume up/down and red key). Oh well. I just talked to the person whom i bought the phone he will just put back original rom and i might just have a dual boot. Hope this will be much better. Thanks guys!!
Learn from our mistakes.... this will be sticky for me!!!
guess samsamuel is the man!!!
well glad you will have a solution. but just so you know - dual boot means one of two things - WM on your phone and android on the SD card or WindowsPhone7 on your phone and android on your SD card. No "real" dual boot per se.
honestly, i would try to look at putting on your preferred rom. good luck!
You mean dual boot isn't good? Is that more of a disadvantage rather than an advantage. Or will a noob like me [email protected]##ed this phone again and will be in more trouble?
Not saying good or bad. Rather dual boot means android is on your SD card. Very easy to get this going. Wont hurt your system. Just being informative.
I prefer nand android but that is my preference. If you will never use windows mobile and only android I would forget dual....but is all about preference. Cheers.
Sent from my HTC HD2 using XDA App