Hi all,
Is it possible to align the screen with some key combination on the Qtek 9100 after a hard reset?
Thanks,
Chris
I think hold down enter then press messaging btn. At least on Hermes.v
I don't think he's asking how to trigger a screen alignment, rather looking for a way to circumvent it.
I'm not aware of anything to help you there....
Related
Hello, sorry to ask such a stupid question, but I am a newbie and I just got this older magician and I was wondering how to set it to factory settings. Couldnt find anything helpful in search...so thanks a lot for any suggestions...
While holding the stylus in the reset hole in the bottom, press the power button.
Hi,
I've a problem with my phone : my dizitalizer screen is out of run and i have been done a hard reset of my phone.
Now the message "tap your screen to set your preferences..." (or something lika that) appears on the screen. Is there a solution to bypass this step or not to see this message after a soft reset ?
Thanks for your help.
Re: Screen digitalizer HS and hard reset
roro10 said:
Hi,
I've a problem with my phone : my dizitalizer screen is out of order and i have been done a hard reset of my phone.
Now the message "tap your screen to set your preferences..." (or something lika that) appears on the screen. Is there a solution to bypass this step or not to see this message after a soft reset ?
Thanks for your help.
Click to expand...
Click to collapse
Sorry to be the bringer of bad news but, "Tap the screen" means just that.
Whats wrong with the screen?
And just for your info, a soft reset is either:
1. Hold Power button longer that 15 secs and turn off / back on.
2. Pressing the recessed button on the right hand side.
A Hard reset is when you hold both the Comm button and Voice button at the same time and reset using the indented button. Keep them held while the device cycles and the reset screen appears.
Re: Screen digitalizer HS and hard reset
Yes I know but my dizitalizer is out of order so I can't tap the screen...
(I used my pdafone without stylet until now since my screen is out of order)
I look for a way to bypass this step because it's physically impossible for me to do the operation.
Thanks for your help.
Jerry-S said:
roro10 said:
Hi,
I've a problem with my phone : my dizitalizer screen is out of order and i have been done a hard reset of my phone.
Now the message "tap your screen to set your preferences..." (or something lika that) appears on the screen. Is there a solution to bypass this step or not to see this message after a soft reset ?
Thanks for your help.
Click to expand...
Click to collapse
Sorry to be the bringer of bad news but, "Tap the screen" means just that.
Whats wrong with the screen?
And just for your info, a soft reset is either:
1. Hold Power button longer that 15 secs and turn off / back on.
2. Pressing the recessed button on the right hand side.
A Hard reset is when you hold both the Comm button and Voice button at the same time and reset using the indented button. Keep them held while the device cycles and the reset screen appears.
Click to expand...
Click to collapse
Any idea ?
a solution
i think i've found a solution. the problem is the software 'welcome' that is in the startup folder of windows. Is there a way to remove it from the rom ?
cook your own rom
Well, people do cook their own roms. Xelencin and summiter do so regularly. moyofalaye has done so too. The welcome screen is part of the ROM as opposed to the extended rom, so that it is a more involved thing to remove it. On the other hand, I am sick and tired of changing my appointment with Dr. Johnson and would welcome a ROM that avoided that part.
Hey guys
I recently installed phone pad international on my phone. It worked fine at first then for some reason the T9 wouldn't spell english words correctly. I decided to remove Phone pad from the program menu
When I did it asked if I would like to reset, which I said yes. when the phone tried to re boot it got stuck on a white screen which I can't get passed.
I have tried to do a hard reset in each of the following ways:
Hold power & reset together - but this doesn't work
Press Power & camera together which just gets me to the boot loader but with no prompts to take me further.
I would be most grateful if anyone could suggest a solution
(the only other thing that springs to mind is perhaps loading a new ROM but i'm not sure how to do that either)
Thanks guys!
This is hard reset:
hold both softkey buttons, and use the stylus to press the 'Reset' button on the bottom.
Bye
hey that was quick, thanks!
which buttons are the soft keys?
phil_fenton said:
hey that was quick, thanks!
which buttons are the soft keys?
Click to expand...
Click to collapse
The ones above the answer (green) and end (red).
Hi all,
i need your help.
I broke my htc touch screen yesterday.
My touch is password protected, i tried to logon but that don't work.
I want to keep all contacts so i can't do an hard reset.
Do you know how to reset my password, or a software that don't need password or any other solution?
Thanks you
- power off your device
- hold SEND and END (green and red) buttons
- Power on your phone
a black screen with some white text will appear. So you just hit ACTION (middle) button and its done
its the only way
if i do that i will lost my contacts. no?
Try "MyMobiler"
-darota-
Darota,
we can take control with mymobiler after unlock phone.
But i solved my problem.
I have a second htc touch on which I took the lcd screen
Thanks to all
okay so my screen has broken, it is not cracked and i do not know what is wrong with it. When i do turn the phone on the backlight turns on but remains black and the actual screen does not when i do manage to unlock the phone even thou i can not see what i am doing i can still touch the touch screen to press buttons as i can feel the vibrating of pressing buttons.
What i really want to know is does anyone know what is wrong with the phone and why its doing this?
Thanks
My phone just developed this exact problem. At first the screen was offsetting the graphics half way up the screen, and hard resetting fixed the problem briefly. Now the screen stays black, but responds to touch and the backlight works.
Did you ever find out the cause, or a solution?
I have a tmous hd2, running a stock winmo and darkstone's new superRAM build.
I just found that a hard reset (hold vol. up + vol down and hit the reset button) fixes my problem.
Thanks xda wiki!
Well, today my screen failed again, in the same manner. Now a hard reset does not fix the problem. I am beginning to think it is a hardware issue. If I fix the problem or find another thread that addresses the issue I will post it here.