Hi all,
Did a search on this, but hoping to prompt some new info on this.
While using my XDA2, running the latest WM5 from TofC via Buzzdev.net, with Tomtom it froze. Nothing too unusual with that, but this time the usual remedy of soft resetting it left it stuck at the splash screen. Same thing happend after removing the battery for a short while. I left the battery in, with it stuck at the splash screen, and the device became quite warm (as though it was working overtime).
Afterwards, I tried removig the battery again and then hard resetting. A couple of times, I have go it to boot MOSTLY, but the backlight will not come on (yep, I have checked the settings) and there are no sounds. Also, when it goes into stand-by, it wouldn't switch back on again.
I have since tried reflashing it with the WM5 rom (stuck at splash screen again), and flashing with the official O2 rom / radio (still stuck at splash screen).
From what I have read, it might be a battery problem, but I have tried charging the battery fully (in the cradle, not in the PDA) and nothing.
The battery I am using is a replcement from Ebay, the original is with a friend so not available for another few days.
Any fresh ideas most welcome!
Well, didn't expect too many replies :roll:
But academic anyway, because the 'brick' is fixed!!! After leaving the battery out overnight (not for the first time, I hasten to add) the XDA2 has decided to boot
It now has an XDA2s version on WM2003 (just thought I'd try it). Pretty sure though the issue wasn't ROM related, because it had been freezing at the same point with this new ROM.
So, anyone with the same problem on their device should not give up hope!
I have a g4 8125 and tried to flash black diamond 2.0 using shelltool. I followed all the instructions, but I may have messed something up. I installed the enablerapi and certspcs files on my phone, but i realized later that i did this after turning off my radio. After flashing I made a hard reset, and now it just comes to the cingular splash screen and shows my ipl, spl, gsm and os (which it says is 6.0.0.0) and doesn't load anything. Anyone have any ideas? It won't connect to activesync either.
edit: sorry for my ignorance, thanks for the help though!
Please refrain from posting WITHOUT using the search bar. This question has been answered more than a million times.
For starters, hold down the camera + power button whil poking at the reset button
Hello there.
This is my first post, and I hopefully pray that I don´t get a "Please Do a search" kind of answer as I have been doing a hard search through the forum but haven´t found what I´m looking for. Probably I´m just using the wrong search terms but english is not my native language so I´m not sure how to look up for this issue.
First, I unlocked the sim of my device by sending it to a third party. Afther that, the phone came with a Wizard-Love OS installed, and finally I got excited and started to mess around with the Shelltool to get the device upgraded to WM6. (It´s a G4 by the way).
First I successfully upgraded to wm6 wee htc wizard v5.2.660, but then I found that the keyboard mapping was all wrong with the shown special characters (they weren´t where they were supposed to be at all), so i tried messing up with the registry trying to select a local language for spanish with no success at all....
Also I was having some issues trying to connect to internet via wi-fi even when I did get connected to the network, but did not test it hard enough.
Then I went farther trying to "shelltool" a Black Diamond 2.0 Touch rom, but then everything became a real mess... The Shelltool said that it was finish only like 4 to 5 minutes after starting so I disconected and Hard Reseted the unit. Don´t remember if I disabled the radio before flashing it, nor if I had the sd card installed on the device at the flashing momment, but definetly i had reinstalled the cert_spcs and EnableRapi cabs prior to this seccond attempt.
After the hard reset, it started but freezed on the first screen showing the ipl, spl, gsm and os (which it says is 6.0.0.0). Then I hard reset like two more times, with no luck. Then I entered on the bootloader mode, but after trying that for a while the phone stopped responding. It did not turn off, so I removed the battery. Then when I put the battery back the unit did not turn on at all. Even it did not show the charging red light when I connected it to the usb nor the wall ac adapter. I was devastated... I leaved the unit with the battery out all the night and the next day I reinstalled the battery to see that the device did turn on and did charge, but still it was locked on the splash window.
I tryed to reflash the unit using the bootloader under windows xp, after killing the activesync connection and using the wizard_Love_2.26.10.2_WEE_Novii_CF2 rom. The unit showed a progress bar so the pc and after 10-12 minutes it was done. I Hard reseted the unit but then it always started on the bootloader screen as if I was pressing the camera button.
Hard reseted, soft reseted, battery out and in, no luck. Then it went dead again. It did not turn on at all and no charging light. Once again i leaved the unit all day without battery and send it to the friend that had unlocked the sim for me. He just called me and told me that the unit was now up and running again with wizard_love rom. I´m really not sure how he did it. Probably i did something with the sd inserted when it was supposed to be out. I did flashed the wizard love on bootloader with the sd inserted but i´m not sure if that could have make the mess.
I would like to know if anyone have had this kind of lock up and how to deal with it (how much time to leave the battery out, etc). Also I will love to know how did my friend (he wont tell me as is it´s bussines and he charges for it) finally restarted my unit flashing wizard_love again, as I´m still too curious to not try to flash my unit again and probably be on the same mess once again.
Thanks in advance.
That's a lovely 1st post. If every one is to be like that.. it would be just to nice to help others.
Anyway, this may not sound logical, but I get problems with Shelltools when I do not have the official ROM flashed before another flash. What I would suggest is that, you ought to have an official ROM (check Wiki to download your official ROM flashing EXE), which seems to get me out of trouble a few times.
Also, it maybe wise to check your battery before any flashing attempt, make sure it is 100% (60% will do mostly, but in case of an emergency, that 40% helps). It cases where a phone doesn't go charge/bootloader, it is battery problem. The overnight thingy that you've done, probably rest the battery long enough to boost it to a charge (e.g. how you get a blink when you switch off a torchlight for period of time on a low batt).
Good also among your information, tell us the IPL/SPL/Radio on the ROM you are using.
HI
wonder if anyone can help me.
Ive had a few problems with my phone ever since i stared to change the roms on it. Something i have just put up with as it goes with the flow. Anyway just recently my phone is really being a pain no matter what rom i have installed . It just turns off or freezes and has also now started to play silly games like all of a sudden everything starts opening on the phone, and sometimes the screen dimms to black then goes off and wont turn on unless i leave the battery out for a good five mins. anybody got any ideas about this all help would be welcomed.
JUst updated the Radio rom to the lastest one i could find on here seems to have helped a bit.
Andy
Have you disassembled it or got it wet? One of the hardware buttons may be stuck. Are they all working?
No all the buttons work ok mate. this evening ive tried a different rom and it seems to be ok ill run it for a few days see if it improves or goes back to being a pain.
I was wondering if it could be the battery its about 12 months old now (due an upgrade an dthinking of the diamond), Phone normally gets fully charged every couple of days.
Hi Everyone,
I'm having some issues with my P3600.
Sometimes (to many times in the past days) while making something on it, the image on the screen suddenly mess up (freezes and weird image) and hangs. Then after the soft reset, somethimes the image stays black, and finally on the 5\6 try it boots fine...
Also noticed that this occurs more while connecting the usb cable jack to sync...
Already make some hardresets and some rom upgrade tests... Also tryed some wm61 cooked rooms, no luck.
Anyone already got this? I think there's must be some problem on the flat cable that connects the lcd-board. Can anyone help me whit some more ideas... before I decide to open it?
Thanks In advantage
SteelwarrioR
it happens the same to me... the pixels all messed up... i dont know wath is the problembut i think its the flat cable ... becouse i have open it one time 3months ago and now its fine. now yesterday have done the same thing
sorry my english
Ok, I open it last night based on the service manual I found somewhere on the Internet, the flat cable looks fine... Now this morning this same situation occurred again, this time while unplugging the usb charger. I Think there's must be some problem on the usb connector. The usb connector is part of the main board so it could be a hardware board issue? Anyone got this on problem on Trinity? Any troubleshooting tips ideas will be appreciated...
SteelwarrioR
hi,
same here. trinity hangs up after some time, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts. I already changed the simcard and removed the sd-storagecard.
The vodafone hotline adwised me to send it in. Seems to me like a hardware issue.
My trin is about 1 year old.
(sry for my bad english)
Andi
No solution Yet???????
hi,
same here. trinity hangs abouth 3 or 4 time a day, screen stays black, when i try to wake it up.
have to hard reset several times and it wont boot for some trys, then with luck the windows sometimes finaly starts
hi, the same to me... it's like the rom's, after a few soft reset couldn't find the necessary files to start again.... and sometimes, after meny tries, it starts well... it's like the ppc processor gets tired and goes to stand by..... it starts freezing the display, and loosing some pixels. so the only things to do is soft resetting the device... any solution? thanks
same with my htc - it appears to me that the errors occur when the trinity was used for a while and the processor was getting warm. the files and folders on the sd-card show strange symbols. but i have also problems when i stick out the sd-card completely.
i will send it to htc repair center - i just hope that they will not send it back as the errors occur only frequently.
so long,
bjoern
solution solved
take taste power and center ok reset take few sec to powering and phone starting
or power and run and stop call reset and phone starting on factory powering
not solved at all
sorry no - this is not the point - i think all guys here have (hard- and soft-) reset their Trinity more than 50x!
the problem is that once the software has crashed you can`t reset it for about 20min - it seems that the processor has to cool down or something like that - after a while (if I´m lucky) my P3600 boots as normal.
I already flashed several new roms - same problem with all of them - I`m pretty sure it`s a hardware failure.
Hello, i don't have any such problem, my Trinity runs very stable even with cooked roms. but sometimes Mobile navigator 7 takes too much memory so the System becomes instable and i have to softreset it.
Hi, mine bug also, and that's begin 2 or 3 days after I have flash to the 1.56.70.11 Radio Rom....
mine worked fine for about 1 1/2 years but suddenly it crashed continous. i havent flashed it and allready hard reseted several times on different days. sometimes it worked for a while but hangs if i started a bigger app like tomtom. vodafone told me they will exchange my p3600. now im waiting for their call
E: Got a new one today which works perfectly so far!
Hi guys,
has anyone had this issue solved without swapping the device?
I have the same problem.....
Bye
Petz
Same problem here...
I have to sftreset or hard reset several times to get it runing again...
In my opinion its some kind of problem with the processor...
Stiil i'm hoping this is a software insue... so that sone one have a hotfix for that...
For my part, when my Trinity crash, I remove the mini-SD, the SIM card and the battery. I just re put the battery, restart (soft reset until WM has realy start, and no more touch or screen freezes), I replace the sim, restart again.. and finaly I replace the mini-sd. It's very long, but generally works well
EDIT:
Finally, I better make my tongue and keep my method for me because at evening begin, my trinity crashed and impossible to turn it on until I finally come back house and have no need more...
my hand that it will crash tomorow morning juste after leave to works
hi, i started getting the same problem.
only thing different is I upgraded to wm6.1 (Mary SL)
I took it back to wm6 which was still locking, then down to wm5.
1week later no issue!
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
just a thought!
xpuser8334 said:
maybe the wm6+ os's needs more cpu than wm5 and causes it to overheat!
Click to expand...
Click to collapse
I don't think so because I downgraded my Trinity to original WM5 and, even if there were less crashes, it crashed anyway.
Now it's still with WM5 but it doesn't start anymore, only backlight.
Ciao
Petz
I want to let you known that my Trinity has run ok for 5 hours without any issue after putting some paper between battery and metallic plate under the battery.
I had to press a little over the rear cover to have it placed correctly because the battery is higher than before.
Keep in mind that it stopped running completely 3 monthes ago, it didn't start anymore and it didn't even go into bootloader mode.
Now I'm using WinMobile 6.5 beta........
Ciao!
Petz
Hi Guys , i have Trinity P3600 in Egypt ,,, it worked perfectly for more than 2 years , but last month it make the same problem like mentioned b4 , hangs , stuck in boot image , or mess in pixel ,,, and i tried to downgrade but no luck, i tried to use different Radio ,, it works sometime , but after a week no , i tried to take out the battery and wait for 3 hours , then back again , so it works but again it hangs if i start my GPS (IGO8) or heavy programs/.
any solution pls
Thanks
Hi
yesterday my htc stalled so I took out the battery but didn't restart it untill the next morning.
Now this morning I couldn't start up my phone.
I let it charge untill the light got green but still no go.
Suddenly it turned on but now I can't use the power button anymore for screen lock.
is this a software fault? or hardware?
Thanks
Frederik
First of all, Welcome to the Forums, I see you've only joined today so make sure you've read all the forum rules etc.
Initially this sounds like a hardware fault somewhere deep in the machine itself. However a few things to try:
1. Take the battery out, disconnect from the charger and leave without any form of power for about 3 minutes (overnight if you can) - Put the battery back in and see if there's any change. - I've used this method to get my phone going after flashing a ROM caused it to freeze at the Smart Mobility screen, as wierd as it sounds.
2. Are you using a cooked ROM? or stock? if you're using a cooked ROM, try re-flashing back to stock and see if the problem persists
3. If you're using the stock ROM, try a hard-reset
It'll also help the rest of us if you can identify which ROM you're using. Perhaps it will be easier if you just update your forum signature to reflect this.
The Wiki is also full of useful information, so have a read of it as well. Here's the link to the Blackstone (Touch HD) Wiki.
hi
it might be some dust or liquid got into the power button but its probably just the switch has died from being pressed too hard or was made badly