I am having a strange issue with my unit. When I first set up the voice tags, everythig was good; I would hit the button on my headset (Jabra 250v) and I would hear the beep, say the name, and then I would hear it back in my headset. Now, I hit the button, hear the beep from the PHONE (NOT in my headset), I can still say the name and the phone repeats it through the speaker, not the headset! Any ideas? the headset is set to hands-free, and the icon is on the screen.
Help?????? Thanks in advance!
Tom
Related
I changed the registry successfully and on my first attempt used the headset to activate MS VC. Trouble is once the call has ended it appears that the 'gateway' is not closed, therefore you cannot make another call via your headset button until the device is 'warm booted'.
Is there any fix out there that will address this problem. Does it have anything to do with the BT vs Widcomm stacks.
Thanks :?
I find if I hang up using the headset button (Scala 500), even if the other party has already cleared down, the audio gateway closes and the next press of the button on the H/S reacivates audio and fires up VC again.
Are you clearing the call from the h/s or just letting the other party clear down to release the call?
Dox
MS Voice issues with Bluetooth headset
to be honest I've not really noticed. At times I would clear first, others it would be the person I called.
All I know is once the call has cleared I'm left with an open 'gateway' If I restart the headset it's still 'open'. It's only when I soft reset that it clears the headset.
It could obviously be different across different headsets, but with the Scala, audio stays on after a VC command, and I need to press the button once to close it, and a second time to get the VC prompt back. Something like this...
Press...
<Mic Symbol>
"What is the battery level?"
"The battery level is 23%"
Press... (to close audio gateway)
Press...
<Mic Symbol>
After a call, I usually press the button just in case, and I don't recall it restarting the VC prompt, so I assume it's closing the audio gateway. Maybe it's just my timing and i'm closing it as we say "goodbye", so I always force the call to close down, even if the other party is doing the same?
There have been a few "VC doesn't work reliably" threads, so maybe it does, as long as the h/s behaves as MS expected. If you don't use the h/s, just the phone VC button and mic/speaker, is VC okay then?
Dox
That's the way it works for me with T-Mobile Vario & Jabber 250 HS.
What I would like to be able to do is disable the Jabbers own ring tone as it masks the incoming caller announcment, and I appear to get the
phones own ring tone played in the headset anyway.
Also is there any way to make just the voice louder?
I think the VC announcement voice is a normal system volume (system), and the phone call is the in-call volume (right) sliders on the volume dialogue that pops up when you tap the speaker icon on the today title bar. I don't know of a way to increase the VC annc over the ring tone.
I did find on my Qtek that there's a hidden system .wav file in /windows called LB.wav which appears as an alarm and is a really loud 'boing' sound. I copied it to /windows/loudboing.wav with Total Commander, removed the system/hidden flags and use that as an alert. I guess, in reverse, you could use a sound editor to reduce the level of the ring tone .wav file and then turn the system volume up so that the VC annc (if that's what you want to increase) is comparatively louder than the ring tone...
Dox
qtek 9000 MS voice commander 1.6 handsfree voiceenable !
It doesn't work , but now http://www.jetwaremobile.com/index.htm I have this ?!!!
But the voice down in my pocket PC. I want that Handsfree is only "ON", not "OF" after click?...
qtek 9000 MS voice commander 1.6 handsfree voiceenable !
It doesn't work , but now http://www.jetwaremobile.com/index.htm I have this ?!!!
But the voice down in my pocket PC. I want that Handsfree is only "ON", not "OF" after click?...
I use Dopod M700 and Handfree bluetooth Sony ericsson HBH-DS-970, I have problem about handfree.
After I compaired such devices, I could listen MP3 by DS-970 through WMP. It's worked and give qaulity sound! But, when I used DS970 as handfree/small talk, It's not worked. I could not answer/call by using DS-970. When incoming call while I listen MP3, WMP stopped but I could not recieved call through DS-970, I must recieved call by M700 only.
How should I do? Help me pleaseeeeeeeeeeeeeeee.
PS : I used official rom and did not install any program.
Go in Comm Mgr BT settings and refresh your DS970 services and ck: handsfree and wireless stereo, save. See if the phone part works.
And if that doesn't work, maybe since the DS970 can only be paired with one phone, it needs to be re-set - then re-paired. I think the instructions are on page 10...yep, found my book: Turn off headset, then press and hold the on/off for 5 secs - you will hear a long beep. Now it is ready to be paired. Next: press & hold the on/off and call handling button simultaneously for 5 secs. The headset will turn off.
When I turn on BT, I find it best just to go into BT devices and refresh the services on the DS970. It seems to behave better...
Thank you very much. I made follow your advise. It's almost ok, but when incoming call, no ringtone in both M700 and DS-970 but it show number and contact. In M700 vibrated only and no ringtone in both M700 and DS-970.
May M700 did not work with DS-970???
Any suggestion. Thank you.
Hello
I've similar problem, i can hear songs etc... i even hear the ring when somebody calls on my DS-970, but when i try to accept the call using DS-970, it is not being accepted, and if press the answer button again, the bluetooth gets disconnected and the phone starts ringing.
Not sure what's causing it.
I'm using O2 Exec with the latest rom.
Please guide
Greets
Hello
No problem i just found the solution to it:
Here's what I did:
* I deleted the HBH-DS970 from the list of BlueTooth devices
* Then I bonded them again (by setting the the little switch on the headset to the left and pressing the power button for about 5 seconds after it had powered on
* Now I move the switch over to the right
Now I can listen to music and when I have an incomming call, I get a short "beep", and I just press the mic button to answer. Then the music pauses, and resumes when I hang up.
Greets
funtoosh said:
Hello
I've similar problem, i can hear songs etc... i even hear the ring when somebody calls on my DS-970, but when i try to accept the call using DS-970, it is not being accepted, and if press the answer button again, the bluetooth gets disconnected and the phone starts ringing.
Click to expand...
Click to collapse
It happened to me when I tried DS970 at the SE shop today. Saddly that I was going to buy it
I am using Atom Life
I have a BT-850 bluetooth headset, and everything works perfectly but every time I turn the headset off for charging and then back on, I have to go to bluetooth settings, delete the partnership, press the button on the headset for the Wizard to find it, enter the 0000 password, tick on Hands free and tap Finish. It is a PAIN IN THE ARSE TO DO THIS EVERYTIME!!
If I turn the Wizard off completely and reboot, the headset still works. The problem happens when I turn the headset off and back on only.
Is there a way around this?
TIA
hmmm.... i also have the 850, and aside from having to use BTaudio to force it to be a stereo headset, i havent encountered that problem.
have u tried just opening it up and pressing the universal button on the headset?? that usually instantly connects me to my phone.
Hmm are we talking about the same headset? Mine is not stereo!
Attached is a picture of it.
Marton said:
Hmm are we talking about the same headset? Mine is not stereo!
Attached is a picture of it.
Click to expand...
Click to collapse
BTAudio pumps system sound (including music) via bluetooth headset profile, as opposed to A2DP to a stereo headset.
So when you turn on your headset, can you press the call-answer button to try and initiate the connection? That is what I do with my Itech S38.
I think my headset is defective. After reassociating, it works perfectly when I press the call/end button on it. The problem is only when I turn it off and back on. I hate to go driving and have to reassociate it when I forgot to do it before jumping into the car...
Marton said:
I think my headset is defective. After reassociating, it works perfectly when I press the call/end button on it. The problem is only when I turn it off and back on. I hate to go driving and have to reassociate it when I forgot to do it before jumping into the car...
Click to expand...
Click to collapse
When you turn your headset off, and back on, then press the call/end button, does it reassociate?
Solved!!!
By a casuality I turned the headset on and kept the call button pressed. It started to blink the red and blue lights rapidly. I then deleted the association on the Wizard and started a search for BT devices. After some seconds it found the headset but with a headset icon (before, every time it detected the headset, it had an arrow or something like that) I then added it and now it works perfectly. When I turn it off and back on, I press the call button and it reassociates alone and opens voice dial. AMAZING!!!!
Thanks for the help,
Marton
Does anyone know if this is possible? I want to make it so when I push a button on my headset it will activate MS voice command So I can tell it to make a call or play a song or what not.
I have a jabra 8040 and just have to hold the botton on the headset until I hear a second beep. about 1 sec later voice command turns on and allows you to do just that.
I got a Jabra headset with my HD and it seems to work fine when I initiate a call.
But if I receive an incoming call something strange happens.
The phone does not ring, but the answer screen pops up.
The headset does not ring either, but I do get a quiet beep.
If I then disconnect the call I get a brief (sub half second of the ring tone).
When I click on the BT icon it says that a Stereo headset is connected.
Not sure what's going wrong, anyone with an Idea?
Cheers,
Paul.