Has anyone succeeded yet, I've got a belkin bt card F8T002 and xp, I can get the devices to bond but that's it, no sync. When I try from xda2 i get some message saying the port may be in use. Also the belkin info says I should be able to see several icons from My Bluetooth Places, I've got nothing, and after I set up the configuration, the information doesn't seem to be saved, when I re-enter the configuration I have to put it all in again.
It's a bit of a bugger really
Hy!
I've an xdaII.
I've the same problem with the USB Dongle's 3Com : 3CREB96B (on my PC).
Activesync doesn't initialisate, but i can send and received files by transfer without activesync.
I borrowed a Blue Tooth dongle from a friend at work. I got the ActiveSync running fine after a bit of messing about. It worked fine both for browsing and syncing with outlook
I only got it to work by selecting 'Connect via Bluetooth'. As this was some days ago and I've not yet had the chance to borrow the BT dongle again I'm not quite sure what I did.
However IMHO Bluetooth is one of the worst connection systems I've had to work with in a very long time .... Last time it was this bad was when you had to use a third party TCP/IP stack with Windows 3.1
Bluetooth Sync
unpair your XDA II and your PC. Then modify the below registry and pair again. After Pairing, run your Activesync in your XDA II and click Connect via Bluetooth in the tools
\HLKM\SOFT\Microsoft\Bluetooth\Activesync
IsBTASsetup from 0 to 1
I'm using - Dell laptop with integrated Dell bluetooth, XDA2 with original 1.03 rom, ActiveSync 3.7.1, Windows XP+SP2. I *AM* able to: synchronize fine with USB cradle, synchronize with IR, and beam files directly to the XDA2 from the laptop via bluetooth.
I have successfully: removed all traces of Widcomm, removed and reinstalled the plain old XP/SP2 BT drivers, have removed the pairings and re-created the device pairings successfully, removed and re-created the incoming COM port, renumbered my incoming COM port to 3, set ActiveSync to 'allow serial connection' to COM3, turned off XDA infrared, tried out "Pocket Bluetooth Tools" too, disabled my firewall. I moved my modem from COM3 to COM13. All the devices are 'working properly' according to control panel. Bluetooth switched to 'On' on XDA, once already paired. Bluetooth Devices/Options/Connections/Allow BT devices to connect is ticked.
Now I have tried to connect as documented in the many webpages on this subject, including GeekZone:
A. On the desktop - ActiveSync/File/Get connected... gives the message 'looking for mobile device on IR and COM3' but then nothing happens. After failing, it shows the list, and COM3 is 'available'.
B. On the XDA2 - Start/Settings/System/Bluetooth settings/Start activesync setup - gives message 'Please bond with device supporting serial port' - then takes me to the bonding screen. But I am already bonded successfully!
C. On the XDA2 - ActiveSync/Tools/Connect via BT with 'Laptop' - gives the message 'Cannot start communications with the desktop computer, critical error 608'.
As the pessimistic bobopopo recommended, I tried doing these last things repeatedly in every possible order!
Possible clues as to the problem:
1. I can't get the bluetooth icon to come up in the system tray. It comes up temporarily if I uninstall and reinstall the XP-SP2 drivers, then goes away next time I reset - even though the item 'Show the BT icon in the notification area' is always checked.
2. The first time I make a pairing, the word 'connected' appears below the icon for my XDA2 in the "Bluetooth Devices" dialog, on XP. Once it goes away, thereafter I am unable to get it to say 'connected' again. How can I get it to connect?
3. First time I bonded I got the Pocket Bluetooth Tools profiles dialog on the XDA2 - and ticked all the boxes, including serial port. Now I can't seem to get that screen back again?
4. On the XP machine, if I go to Control panel/Bluetooth Devices/Devices, select the XDA2 that is paired, then Properties/Services, I get only 'Dial up networking', and no exciting stuff like COM, OBEX, audio, PAN etc. - is this right?
5. If I go to Control Panel/Bluetooth Devices/COM ports/Add/Outgoing, and put Browse.., it searches for a while then says 'Windows cannot find any Bluetooth devices. Make sure it is switched on' etc.. although the device is clearly visible. So I can't create an outgoing COM port.
6. Can't beam files from XDA2 to Laptop: though XDA can see the other machine when you try to pair, it can't see it when you go to File/Send To/Infrared recipient - just empty dialog 'Searching...' forever. ('Accept incoming beams' is on and Bluetooth is on.)
????? Is it me or is it Microsoft ?????
mate,
reading through your post (although don't consider me an expert on this) it appears that you have the same problems i had before. bottomline? i discovered that windows xp service pack 2 screws up installation of bluetooth software. took me ages to figure this out but what i did was uninstall sp2 and went for sp1 instead. i've read several posts here and in other sites that sp2 doesn't really do well for bt apps...not sure if this is the same for the other chaps but it sure was for me. anyway; i uninstalled all bt software, uninstalled sp2; installed sp1 (reboot, etc), and from there proceeded with reinstalling my bt and activesync apps. from there i followed the guide given in geek zone and presto bt activesync.
the items you described in 1-6 definitely remind me of the sp2 trouble i had.
hope that helps.
cheers mate
I found that if I use the cradle to link to activesync this will create the partnership, then use the bluetooth next time and it will work, it seems you cannot get an original partnership over bluetooth.
I don't think its SP2 itself thats the problem. Its the Microsoft bt stack built into SP2.
You can actually run SP2 and the Widcomm bt stack. If you install Widcomm before SP2, then it won't install the Microsoft bt stack. I had the same problem and this resolved it.
The Microsoft bt stack in SP2 is Microsoft's first attempt at bluetooth. Looks like they still have work to do.
JD
Bluetooth activesync is easy IF YOUR NOT in Windows XP SP2!!! best thing to do is to downgrade to SP1.. unfortunately for me im stuck with SP2 in my desktop... but upon discovering this problem i never upgraded my laptop to SP2.. i left it with SP1 nd everything works in harmony...
MORAL LESSON OF THE STORY: NEVER UPDATE TO XP-SP2 if your using bluetooth activesync. :wink:
I've had no problems syncing over BT with SP1, SP2 MS stack and widcomm.
Here's how.
First of all delete any pairings on both PC and XDA.
Sync over USB then on the computer use connection settings to select the correct BT com port.
On the XDA goto Settings->System->Bluetooth->Start
Now repair your device and select ok till you get back to today screen
Goto activesync and then tools->sync over bt
Always has worked for me. If you're still having problems its quite possible that you haven't got the right ports setup on the PC.
YUP! it's all about the COM ports... SP2 gives out extremely high COM ports that activesync doesnt recognize...
Is your PC using...
1. SP2 + MS bluetoooth stack
2. SP2 + Widcomm bluetooth stack
I've followed the method laid out by fruitloaf many times, and only the 2nd combination works for me.
You might also want to consider upgrading from rom 1.03 if you can.
JD
fruitloaf said:
I've had no problems syncing over BT with SP1, SP2 MS stack and widcomm.
Here's how.
First of all delete any pairings on both PC and XDA.
Sync over USB then on the computer use connection settings to select the correct BT com port.
On the XDA goto Settings->System->Bluetooth->Start
Now repair your device and select ok till you get back to today screen
Goto activesync and then tools->sync over bt
Always has worked for me. If you're still having problems its quite possible that you haven't got the right ports setup on the PC.
Click to expand...
Click to collapse
Fruitloaf, is yours an original Orange machine? I've heard this works with SP2 + MS stack, but the O2 Xda II doesn't.
JD
I had this problem constantly with my XDA II and a Toshiba Laptop. All routes of advice came to nought.
The answer for me was to install Pocket Bluetooth Tools, a BT connection manager which has a specific Activesync Profile. Using this has enabled me to use BT A/S with my Win XP Tablet SP2 PC without problems. You have to initiate the Activesync process from the XDA though.
Once you have installed BT Tools, and created an A/S profile using the cradle, go back to the XDA and delete all existing BT Pairings. Then go through the "Bluetooth / Paired Devices/ New routine again. After finding your PC, continuing will give a new Dialogue box with available pairing options. Select "Activesync" and finish. Do a soft reset.
From there, go to Start/Activesync, then tap Tools/Connect via Bluetooth and all should work.
I recommend using PBT Tols version 1.0.1.2 not the newer version, as the later version causes some power management problems with the XDA II.
Available Here
bluetooth virtual com port too high for activesync
I have a Belkin F8T001 v2 BT USB dongle. BT was working under win xp sp2 and could transfer file etc from PC to XDA IIs and back.
However I tried setting up a BT active sync connection and had the problem that the virtual com port picked by the belkin supplied widcomm BT driver was too high for activesync, it was com20. I followed this thread but could not uninstall the driver and use the driver from SP2 as it doesn't seem to support my belkin USB BT dongle. So I had to go back to the driver supplied by Belkin. I thought I was stuffed until I came across a post that sorted the problem, I'm afraid I dont have it to hand to give author the credit. But here is what he/she said to do.....
1. Disable bluetooth in device manager and remove the high numbered com port from device manager.
2. Then use regedit to change
"HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\COM name arbiter"
I followed the instructions and changed the first 3 entries in theComDB field to be "0f".
3. Enable Bluetooth in device manager
4. Use bluetooth settings -> local servies to add a new COM port, then set it to autostart in the profiles section.
This time it came up as com5, and bingo activesync could find it and I was off....
Hope this helps others with this problem, usual disclaiamer when fiddling with registry back it up and dont blame me if it doesn't work or your equipment goes up in smoke
Good luck, Wayne
http://www.geekzone.co.nz/content.asp?ContentId=3163
this guide works just fine for me
Marc MD said:
YUP! it's all about the COM ports... SP2 gives out extremely high COM ports that activesync doesnt recognize...
Click to expand...
Click to collapse
That's is my problem, the high COM ports are not recognised by ActiveSync! I think i have 2 downgrade to SP1 and then upgrade again to SP2, hopefully that will work.
The BT drivers is not my problem but it's impossible to select the com port in activesync (but the com ports are visible in the device manager!).
Thanks to this forum for geving me hope , now i know what the problem is.
If you read my post with the registry change above I think you will find it will solve your problem, as I stated this was the only problem I was having with the BT driver.
This is a lot simpler than downgrading to SP1 etc.
AT last I done with this help and use widcomm Bluetooh Software 1.4.2 bulid 10 now my active snc work great with winxp sp2and wm2003se ..
just flow the thats:.....
This issue may occur because the Bluetooth drivers that are provided by Microsoft support a different set of profiles than the drivers that are provided by some third-party vendors. The Microsoft-provided drivers are also signed and will therefore be installed instead of a third-party driver for supported Bluetooth adapters. The Windows XP SP2 Setup program will try to detect if a third-party driver is present. If the third-party driver is installed, the Microsoft-provided Bluetooth drivers will not install. This action makes sure that an existing configuration is not modified. If both provided drivers were installed, and the Bluetooth Radio were connected to the computer, the Microsoft-provided driver would load because it is signed.
If the missing functionality is critical, you may restore the third-party support. To do this, follow these steps.
Note The following steps assume that the third-party software is installed. If it is not, install the software according to the manufacturer's instructions. Then follow these steps from the point in the installation process where the adapter is connected to the computer.
1. Click Start, and then click Run, type devmgmt.msc, and then click OK.
2. Locate and then expand Bluetooth Radios.
3. Right-click the Bluetooth adapter, and then click Properties.
4. On the Driver tab, click Update Driver.
5. Install the updated driver manually by using the Have disk option in the wizard. Locate the manufacturer's installation files, and then find the .inf file that is required to install the driver.
6. Complete the manufacturer's software installation steps.
At this point, the third-party provided drivers should work. If at any point you re-enumerate the Bluetooth adapter, the Microsoft driver will be reinstalled, and you must repeat the procedure. This issue will occur only if the third-party driver is removed or if another model adapter installed.
thats link is for bluetooth software v 1.4.2.10
http://asia.giga-byte.com/Communication/FileList/Driver/btd01.v.1.4.2.10.zip
i've tried everything but it still gives out high COM ports...
Marc MD said:
i've tried everything but it still gives out high COM ports...
Click to expand...
Click to collapse
Go to device Manager, find those high Com Ports, choose Properties - Advanced and at the COM port number choose a low one, Like COM3 etc. Don't bother if it say that it is alreaddy in use...
The go to Active Sync and in the Connection Settings choose from the drop down menu COM 3...
Go to the Activesync in you XDA, in the Options choose connect using Bluetooth and the... click on Connect via Bluetooth from the XDA...
You're done...
I have an O2 Xda II Mini (Magician) and I am using an XMicro Dongle on my laptop (Win XP with SP2) and ActiveSync3.8. Initially syncing with BT was a problem but now its not a problem at all.
To reduce the COM port nos. on your computer try the following website
http://support.microsoft.com/default.aspx?scid=kb;en-us;315539
Once you can see the hidden devices and ports delete/uninstall all the ports which are not in use.
1 To sync with BT first delete all your pairing with your computer and phone on both devices.
2 Go to BT Manager on your phone and click both check boxes for Inbound and Outbound COM ports and pair the devices.
3 Once they are paired go to BT manager again and click on the start button (for BT activesync setup) and pair the devices again if you have to.
4 Once that is done check on the computer in BT Manager click on the phone device>property>services....the Serial Port Profile (SPP) "Serial Port COM4" will be checked.
5 After that on the computer's BT Manager itself ensure that the COM ports folder shows incoming and outgoing ports with the phone's name in front.
6 On the ActiveSync (on the ocmputer) ensure that the COM port no. is the same as the Incoming COM port no. given in step 5 above and it being shown as available. Sometimes if it is unavailable, the computer needs to be rebooted and then it will be shown as available.
7 Click on ActiveSync thru BT on the phone and it should work.
It has been working for me since the past couple of weeks. Initially it took a lot of time to set up but now even if the pairing gets deleted or something messes up its working fine. One thing to remember is that in case you are using a dongle with a laptop ensure that the dongle is plugged in BEFORE you boot up the laptop. A lot of people plug it in later and then ActiveSync on the computer shows the COM ports as unavailable.
Hope this helps.
Hi, I just can't make the activesync over bluetooth work with my laptop (widcomm) and my magician (qtek s100).
the devices are paired enough, and I can see the serial port on the phone from the laptop, but when active sync starts to search for the connection, it loses the connection (the serial port is listed as not connected in the "my bt places").
Any tips/hints? Is something wrong on one of the machines? I will try to see if I can test with some other devices...
try this --> http://howardforums.com/showthread.php?s=f18b052a41d1d7b711c2b97ecd926005&threadid=544932
You can skip the step on installing and using the BT Tools.
cheers :wink:
Thanks, but that doesn't work for me...
I can pair allright, but I am unable to sync...
have you updated to the latest ROM for your s100? I noticed after updating my JAM that I do not need BTH tools anymore to activesync over BT.
Hi
have an O2 XDA II Mini (Magician) and I am using an XMicro Dongle on my laptop (Win XP with SP2....I am using the in built Microsoft BT stack which comes with SP2) and ActiveSync3.8. Initially syncing with BT was a problem but now its not a problem at all.
First you have to make sure that the COM port nos. selected by ActiveSync are less than 10 bcoz there is some bug due to which ActiveSync will not support COM ports above COM9.
To reduce the COM port nos. on your computer try the following website
http://support.microsoft.com/default.aspx?scid=kb;en-us;315539
Once you can see the hidden devices and ports delete/uninstall all the ports which are not in use.
To ActiveSync.....the following steps might help....
1 To sync with BT first delete all your pairing with your computer and phone on both devices.
2 Go to BT Manager on your phone and click both check boxes for Inbound and Outbound COM ports and pair the devices.
3 Once they are paired go to BT manager (on the phone) again and click on the start button (for BT ActiveSync setup) and pair the devices again if you have to.
4 Once that is done make sure that on the computer in BT Settings the the Serial Port Profile (SPP) "Serial Port COM4" is checked.Click on the phone device>property>services.
5 After that on the computer's BT Manager itself ensure that the COM ports folder shows incoming and outgoing ports with the phone's name in front.
6 Open ActiveSync (on the computer) ensure that the COM port no. is the same as the Incoming COM port no. given in step 5 above and it being shown as available. Sometimes if it is unavailable, the computer needs to be rebooted and then it will be shown as available.
7 Click on ActiveSync thru BT on the phone and it should work.
8 Whenever you wanna disconnect ActiveSync press stop on the compouter to disconnect.
It has been working for me since the past couple of weeks. Initially it took a lot of time to set up but now even if the pairing gets deleted or something messes up its working fine.
One thing to remember is that in case you are using a dongle with a laptop ensure that the dongle is plugged in BEFORE you boot up the laptop. A lot of people plug it in later and then ActiveSync on the computer shows the COM ports as unavailable.
I hope this helps.
All the best!
Has anybody managed to get this working. I have got as far as getting a serial connection on com14 to connect for about 20 seconds (it then disconnects automatically) - setup activesync 4.1 to check on this same port but it says it cant connect.
When I paired it did create an ativesync bluetooth service on another port com6 but I cant seem to find a place to make this connect.
D-Link DBT120 dongle.
Any suggestions? What other info can I supply
Thanx
Tim
Sunny South Africa
Try setting it to a COM port < 10? I have mine on COM1, and my Exec connected with no problems... even on the initial Partnership setup. I've never plugged my Exec into my PC via USB!!
My Exec works fine on COM 20.
I used the Help information on BT in AS to set-up and it worked first time. I use a Belkin BT dongle
I encounter the same problems. Set the device to COM 5, the PC takes 7or 8. The device won't let it self be changed to 7 or 8, it only takes 5. I get a BT connection but no AS.
I read some issue about closing the firewall when setting up the account. I did that when I connected over UBS and succeeded to establish a relationship, but not by means of BT.
Thanx Jah for the tip - I hoofed the D-Link drivers and used the windows ones rather and it worked as you said
Tim
Anyway to make the BT connect and activesync automatically when the PC starts up or even better when you get in range?
buckinghamrd said:
Anyway to make the BT connect and activesync automatically when the PC starts up or even better when you get in range?
Click to expand...
Click to collapse
Yup, I am desperately waiting for this tooo....
Hi there,
I always synced my phone bluetooth with my laptop (Windows 7 x64)
My laptop is bluetooth visible and devices are allowed to connect.
my phone sees my laptop, and me laptop sees my phone
when i bluetooth connect them it seems to go ok, but in the Windows device manager from my laptop it says cannot find drivers.
Strange because i downloaded the latest windows mobile center
I have an unknown bluetooth periphal device in the device manager
USB connection does work properly and the sync! i also can reach my 8Gb SD in my computer
Cheers!
I removed the initial question about the bluetooth connection with my carkit.
The initial question is a problem of my car, don't ask why but i tested bluetooth integrated carkit with a other phone and it also does not work properly so something in the wiring of my car is stuck and is not for this forum. First it DID work with the other phone
I cannot find how to change the thread type to "Bluetooth connection with WIndows 7"
nobody has problems with windows 7 drivers?