I am encountering a problem where after some time (do not know how long exactly) my BT headset seems not to synchronize with my TyTN. So when an incoming call arrives I am unable to answer it using the BT headset. Also, when I try to use Voice dialing it efuses to use my BT headset.
Only when I do a soft reset it works.
any ideas?
I have the same problem with a SonyEricsson HBH-610A.
Some times the bluetooth stops it self and I have to activate it agan.
Today when I tried to install the headset again, it searched forever and then I got the message, "Problem with Internal Bluetooth Hardware" and a OK button??
Only when I do a soft reset it saves the problem.
It actually drives me nuts, because I want to answer calles when the TyTN is in its holster.
I am using a Plantronics 655 with my TyTN running VC 1.5 with the common registry hack and have similar problems but not exactly the same. I want to be able to initiate voice dialing via the headset but when VC repeats the command it comes through the phone speaker and not the headset which also means my confirmation of the command has to be through the phone rather than the headset. Also, when a call comes in my TyTN speaks the name and number of the calling party through the telephone speaker but only beeps in my headset. To me it should be speaking to me through the headset.
I'm trying to get down to the bottom of this issue so it can be resolved through coordinated pressure on the responsible party(s).
Any help I receive will go to help all BT users of VC on the TyTN.
I am using a Plantronics 655 with my TyTN running VC 1.5 with the common registry hack and have similar problems but not exactly the same. I want to be able to initiate voice dialing via the headset but when VC repeats the command it comes through the phone speaker and not the headset which also means my confirmation of the command has to be through the phone rather than the headset. Also, when a call comes in my TyTN speaks the name and number of the calling party through the telephone speaker but only beeps in my headset. To me it should be speaking to me through the headset.
I'm trying to get down to the bottom of this issue so it can be resolved through coordinated pressure on the responsible party(s).
Any help I receive will go to help all BT users of VC on the TyTN.
Related
Has anybody got the above or a similar headset to work with the jasjar and ms voice command 1.5.
I have tried the advice in several of the other posts and i am not getting anywhere fast.
I have a successful pairing with the phone and the headset, as the headset kicks in and allows me handsfree operation whilst driving. I had no issues installing ms voice command.
I have downloaded resco and altered the settings in the registry like advised by rilot in earlier posts however all i get when i push the button on the bt headset is a neverending intermittent beep which only goes off when i power down the headset.
Anyhelp as always is greatly appreciated. I would love to get this software, or even the bundled cyberon voice speed dial software, to work of the headset
I've just got jabra bt800 to match my xda atom. I've paired the earpiece with my atom. It works fine when receiving and making calls. However I really want to know how it can initiate voice dialup program by clicking buttons on my bt headset. I tried different ways even combination of buttons. It didn't work!!!!!! I think there must be some work 2 be done on the registry.
Can someone help me out????
btw, if I hold the call button on my headset, the phone software switches on
Hi All: I have paired the headset fine with my phone and made calls before but I can not switch a call from the handset to the headset while a call is already in progress. Once I end the call, I can pair the headset fine to make a NEW call but I'm having problems switching the call when it is already in progress. I can go to the phone and manually switch it to hands free but I thought that if I powered on the headset while a call was already in progress, that would route the conversation from the handset to the headset. Is that correct or can it not do this without some tweaking? Thanks.
I have the same setup and I can answer the call on the phone, then "open" the H700 and the phone re-directs the call thru the headset within about 2 seconds from opening the headset.
If I'm on the headset, I can press and hold the call button on the H700 and the call goes on hold. I can "close" the headset and then un-hold the phone using the touch screen and resume the call on the 8525.
Now I believe that the standard bluetooth stack is crap, and I have had many instances where the phone just stops linking the Bluetooth. I can usually restore the link just by using the comm manager to turn off the bluetooth radio, then turning it back On. I have even done this during a call and it worked.
I have always had solid, loud audio with the H700, BUT, several callers have mentioned that my voice was often clipping a word every few seconds. I don't know what that's all about.
Do you know whether you need to select any special settings or do anything special in the pairing setup with the phone or headset? I do not know how to have the conversation directed to the headset after turning it on when I am already on the call. It works fine to start a new call or to answer a call directly through the headset but can't join a call in progress. Would appreciate anyone's help. Thanks.
Hi everyone
I have Eten M700 with WM6 ..
I tryed couple of bluetooth headsets (regular, not stereo) and i was able to pair all OK & make and recieve calls
I was even able to divert all sounds to headset to listen to my music (using either btIO or Blue Music)
I also have MS voice commander 1.6 US & it works through bluetooth without problems
I still have one problem:
when i end a phone call (touching red screen dialpad button or by hardware button) or even by waiting for the person on the other line to hang up..then my headset disconnects (i do not see the headset icon on top right of dialpad) and on the next phone call i have to restart pairing by pressing the headst button (it should start automatically & not disconnect)
i do not have to enter pairing code but it is still one extra step that i did not have to do with other phones..also, i miss some calls because when it disconnects i may not hear my phone speaker ringing as i will be away or driving
Does anyone else have the same problem?
Any fix (software, cab or reg tweak) out there to keep the bluetooth headset connected and paired inbetween calls (not disengaging after a call ends)
Thanks
I have the same problem, though i use my DS-220 as a wireless stereo also , i have no problem using it as one or another (handsfree/stereo headset) but as soon as i'm listening to something and i answer a call, sometimes, the headset disconnects itself after a call and i also have to push the button on the headset to connect it again - but not every time, best solution to resolve this problem for 70% of occasions was to uninstall Microsoft Voice Command 1.6 which was messing up with the BT on my phone, since it uses the handsfree's talk/end button as it's own "engage" button, but still, sometimes, this error occurs
I was wondering, if someone of u has working BT Widcomm or any other better BT stack (better than the microsoft bull*hit) and would mind PMing me the link, I could try it out and see, if that's the solution
BT new fix needed
This dsconnection has been happening with me even before MS voice command installation
i did not notice difference with it installed, i am alble to make commands without bluetooth droping & i give my commands through the BT headset without any registry hacks (read something about people having to give commands through phone speaker not headset) i do not have that problem
my only issue is the dropped connection after finishing a phone conversation (by ending a call or other side ending it)
I need a good developer to fix that & also, maybe work on dr.Yar BT software that shows sender/reciepient ID and file progress. that software shows blank white pop-up window when recieving files from some devices.. maybe also add a clickable line to make BT discoverable or hidden to the menu list there
i use BT only for regular mono headset & file transfer, i route music to my mono headset with BlueMusic v2 sometimes too.
If these 2 issues are fixed im all set (droped with calls & ID/progress blank window in Dr.Yar)
Thanks for looking
nothing
no one has solution for this???
So I recently got a Plantronics Voyager Edge headset and noticed an interesting bug...
Every function appears to work fine. I can communicate with the phone via voice through the headset. And if I search for a business or something and hit the call button in the search results, everything works fine.
If, however, I dial a number manually or select a number from my contacts - the call isn't immediately sent to the headset. I have to toggle the speaker phone and then back to the headset to get the call to go through the headset.
Anyone had this issue? If so, is there a fix you're aware of?