I have new ROM WM 2003 4.01.16.Is this stable one?While installing exe file it shows current ROM and Upgrading ROM 3.16 How is that?I have downloaded 4.01.16.Is there anything wrong
This is just a header string, it doesn't matter and it will not be shown in the device info as long as you cooked the right ROM.
Some people reported issues in 4.01.16 but not that severe, but I think 4.01.00 is the most stable one.
Softrest Everytime after Upgrading WM 2003 4.01.16
I have sucessfuly Upgraded my Qtek 1010 with WM 2003 4.01.16 by Bootloader method Thanks to Biso007 for his help.But now when Qtek turns off after 3mins It doesnot switch on even after pressing Power Button i tied several times.Now i have to do Resest Everytime or uncheck the box for turning off the device.
Whats wrong what to do I miss calls now.
Can i reinstall the same ROM or any other
Hey All,
Recenty tried to upgrade by Wallaby using the SD card/Bootloader trick. Cooked a ROM for MW2003 SE and got it onto the SD no problems.
All went through per the instructions and I was happy.
Did a hard reset. Waited 30 seconds and then did another hard reset.
Unit will not boot.
Do a soft reset. Still no boot.
Hold down power and do a soft reset gets me into the boot loader.
So, I have a unit which won't boot.
Any ideas ?
Cheers
Sonny
try upgrading again ?
try downgrading to an old 2003 rom ?
I tried about 3-4 different ROMs that I cooked. None worked. Same problem.
All started when I loaded in the T-Mobile update.
Should I try loading the same ROM a few times in a row ?
Cheers
Sonny
tried the fix bootloader in the xdatools ?
I have bootloader 5.17 so using the bootloader patch which is working fine per the instructions on this site.
When I load in the T-Mobile ROM, everything is fine although the SD Backup application doesn't work and I can't restore all my backed files.
If I could get SD BAckup to work, Id be happy with the T-Mobile ROM.
When I load in the T-Mobile ROM, the Wallaby Patch loads the ROM and checksum is ok. When I use any other ROM, the unit will not boot and the Wallaby Patch gives me a checksum error.
So, is there another version of SD Loader I could use ?
Oh, and when I try a .EXE ROM, like the 2003 ROM, I get an error about the USB port being closed and I can't get the file to load.
Any ideas there ?
Cheers
Sonny
You can try downgrading the bootloader.
Read this document here:
http://lumpistefan.dyndns.org/tools/manual2_unlock.htm
HTH
Stefan
My O2 XDA is quite old and I have been running a revised WM 2003 ROM 4.01.16 Eng with radio 4.21 for ages.
I want to put back the original rom but can’t get to the bootloader! I have tried every combo of Soft reset and Hard while holding down the power button excreta but noting. What am i doing wrong ? I have a ROM made by XDAtools (i thnk its ok)
Just to add the ROM is T-Mobile - ps its the one you cant upgrade with .EXE PLEASE HELP
Just to add the ROM is T-Mobile - ps its the one you cant upgrade with .EXE PLEASE HELP
Using activesyn?
Harry, have you tried using the bootloader patch in xdatools, if you have xdatools installed, go to start on your desktop then programs/xdatools. An option to fix broken bootloader should be there.
Harry, have you tried using the bootloader patch in xdatools, if you have xdatools installed, go to start on your desktop then programs/xdatools. An option to fix broken bootloader should be there.
macihne gone now - ive now got XDA II Tnx for all help
Hello,
I have flashed my MDA Vario with a WM6 rom dutch witch worked fine. After i changed my pagepool to 6 MB and soft rebooted my MDA, it stared, but without phone functionalty. every program i try to start it gives me the message that it has no memmory to start the program.
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance
Try bootloader mode?
Bijdehandje said:
Hello,
. . .
No activesync connection (or any other connection) can be established. I have found some articles on flashing xda pda's from sd card. But in these articles they talk about .NBH files. The only file i can find in the update util is an .NBF file. Can anyone help me solving this issue?
TNX in advance
Click to expand...
Click to collapse
Can you get into bootloader mode (tricolor RGB bands)? ("Get your phone in bootloader mode by doing this: Phone powered off, press Camera button + Power On, will enter into bootloader mode (RGB screen").
Once in bootloader mode you can reflash even though activesync says not connected - just look for little USB in corner of screen.
Tnx cushcalc for your reply.
I have tryed it just a minute ago. I can enter the boot loader but the flashing fails at starting with the message "This update utility cannot be used for your PDA Phone. Please get newer update utility". I have used the same flash tool as the rom image witch is now on the MDA.
Sounds more like CID locked after flashing the last ROM was flashed....cant u even flash any other wm6 ROM?
You should flash the original T. Mobile ROM from bootloader it should work. After you have the original running you can then re-flash WM6 using shelltool if your phone is CID locked. Try it and lets see how it goes.
You people are the greatest. I have tryed to flash my MDA Vario with the latest rom from t-mobile and now i have a fully functional mda again. BIG TNX for helping!!!
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
which is your device,post full data of your phone,IPL/SPL...? Make...?
As you say you installed through Shelltool,is it a G4 DOC chip version ?
You say it's stuck at the splash screen with ipl/spl and gsm version,which splash screen,is it OS (Rom) initial splash screen or a Bootloaders (Multicolored) screen ?
Secondly ,try to get it into bootloaders (multicolor) screen,if it gets into bootloaders,connect it to PC via usb cable,check small usb appears at the bottom of the bootloader mode in the phone,if it does,than flash a carrier's official Rom to recover back to it's default status.
Good luck
Try the Button's ROM (which is in Wizard Upgrading subforum). Then unlock it again (It may be causd by a fake CID unlock when you try to unlock when IPL/SPL is 2.xx)
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
alldoe said:
My current
IPL/SPL 2.24
GSM 02.25.11
OS 2.24.10.1
I have G3, but I was using ShellToll because I can't install by RUU file.
My Wizard stuck at ROM Splashscreen, i can get into bootloader screen, but when I flash any ROM, everything upgrading well but after Reboot it still frozzing at Splashscreen. I was tried Button ROM sometimes but it doesn't work, I have CID unlocked by Imei-check.uk and everything is okay, I can install ROM from G3 and G4 chips. And ... I remember, that before CID Unlocking my IPL and SPL have different value.
PS. I was unlocking my CID, after my Wizard bricked.
Click to expand...
Click to collapse
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
luoluomeng said:
You can download this rom CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe on XDA,it contains IPL/SPL 1.01,and upgrad this rom,then you'll find your IPL downgrad to 1.01,and SPL still is 2.24,and then,use aWizard tu unlock your CID,after this,your CID should be unlocked,you can use RUU upgrad any rom you want.
I just do this yesterday,my CID isunlocked now.And RUU now works on my device.
Click to expand...
Click to collapse
Hello! I have CID unlocked. When I install Button ROM my IPL and SPL is the same (1.01). Every RUU works but It still frozen. 2 Days ago i found on other forum this advice:
INSTRUCTION :
1. miniSD - formated in PC - FAT format (now FAT32 !)
2. Wizard On and Bootloader (press reset and keep photo button let go reset) 3 color display. Put in card to Wizard.
3. Connect USB - PCC to PC
4. Launch MTTY 1.42 (my ver.) with USB connection
5. Write command - r2sd os end press enter
6. Program it will record OS on miniSD
7. After recording make Hard Reset or turn on Bootloader
8. On Display should be written - Format partition ?? (5 sec.) - to confirm press Voice dial button. If inscription it will disappear repeat point 7.
9. If Format partition successful wait OS is write. Done.
10. Draw out miniSD
11. Make Hard Reset
12. Enter in bootloader
13. FOR NON CID WIZARD - Flashing Wizard RUU (must be proper version) - ERROR 300 is bad RUU ERROR 266 turn off Wizard and turn on connect to PC
14. With CID (for example CID G4) seek forum for flashing Wizard with CID G4
My Wizard it lives
Click to expand...
Click to collapse
I was carry out all command step by step, and after flashing proper version Orange ROM my Wizard woken up, but today my Wizard get stuck again and now this way don't work, and I have to find a new method to rescue my PDA.
My Wizard woke up! I find ERA PL ROM (RUU_Prodigy_3829_382130_027111_TMO_PL_PLK_Ship) which flash excellent and working, but now I have a new problem. I can install other ROM after that but none of them work, every stucked at Splashscreen like before.I need to find some WM6 ROM which will working? Someone have some suggestion?
alldoe said:
Hello!
I have strange problem with my Wizard. 4 month ago i was trying to install Pathfinder 1.2, but when I installing this ROM using ShellTool my PDA bricked. Now all the time it's frozen on Splashscreen with IPL/SPL GSM and OS information. All HR completed without any errors and all ROM's upgrading finish correctly.
Once time, after 2 months for breaking, my Wizard just started and working very well, I do 2 HR and few SR and my Wizard still working good, but when I shut it down and pull out battery my Wizard again frozen and until now can't wake up. I have CID Unlocked by imei-check. I tried to install many different ROM's, e.g. Wizard Love, Dopod (CHS), T-Mobile, Orange (PL) but nothing work. I also tried way with SD Card but my ROM's doesn't work, I think I need some working dumped ROM. I was searching help on few forum but poeple on polish forums don't know how to help me. May someone here have idea where can i find working dumped ROM or have any other idea how can i fix my Wizard?
Thanks for any help
alldoe
PS Sorry for my english
Click to expand...
Click to collapse
i have the same proplem but i have a g4 wizard and it's not cidlocked tell me plz what to do plzzzzzzzzzzzz :'(