can anyone help me on how to connect to the internet via Wi-Fi without using GPRS.
turn wifi on. it must serch acess points automaticly. then follow instruction. at least, you must know password or your MAC adress must be registred on internet provider.
Hi I have a O2 Atom and tried connecting WI-FI with my Laptop but it would not. Can you tell me the procedure. I tired turning the Wifi on but it will not. I went to settings>connections>wifi Utility>Menu>Turn On Wifi but it just shows satuts as Wifioff. I checked in Menu>about and it shows Driver Version: Wifi not enabled, Firmware Version: Wifi not enabled, Mac Address: Wifi not enabled.
I am using the latest ROM Official update. What could be the problem? Is there any tweak to solve this problem. Please assist someone.
if you have the latest ROM, use wireless manager to turn on wifi.
tap on anthena on upper bar, then tap "wireless manager", then turn wifi on.
regards
Wifi OFF Will not turn on
I tired it but it would not turn on. I can turn on and off the radio or the bluetooth but the wireless. Would not go on. So I tired through Settings as mentioned before but that too does not help. Please tell me what I can do?
1. Run selftest, to be sure, that it isn't hardware problem
2. Try HARD RESET
In your notebook configure wireless software to Ad Roc, default is infrastructure
I tired Self Diagnostic and the WLAN Module Test Detected a Mac Addr: 02-02-b3-92-a8-c4. Then I reset and then tried to turn it on but does not turn on.
I checked my computer settings and it is set to Ad-Hoc. :?
Please someone assist me
I have noted one thing for sure that when I am away from my computer and have checked the wireless Manager shows the Wifi: Off.
When I click Menu > Wi-fi Settings it goes to creating a new profile. But when I am close to this laptop I want to connect to the profile page does not show. :!: :!:
WHY is this happening :?: :?: :?: :?: :?:
SOLUTION to WIFI Problem In O2 Atom
I had tremendous problems with my O2 WIFI which would not connect to my laptop WIFI LAN Network. I asked O2 People & Lot of people on this and other forum but got no perfect response.
Practically trying many options I by chance put back the old ROM upgrade of O2 2006123-45 and tried switching on the WIFI and lo and behold it worked fine.
Then I reload the new ROM 20060426 again and it works fine.
This proves that if you reload the NEW Upgrade ROM more than once it locks the WIFI.
Wi-fi Shut-off when we do the first activesync.
I tried closing all programs by going to settings => memory => running programs => close all.
After that I did the soft reset and started the process "Start => Settings => Connections => WiFi Utility => Menu => Turn on WiFi.
Menu => Jump to Network Cards 3. Under Wireless, select your desired network. (If your network is hidden, kindly tap on "Add New")
Enter your network name (if needed), proceed to Network Key.
Select your Authentication, Data Encryption type and your Network key.
Proceed to 802.1x if needed (it is usually disabled)
Tap on Ok, go to Network Adapters => O2 Wi-Fi Wireless Adapter
Configure your IP and Name Server if needed. (If your network allows automatic assign, you might want to exclude this portion)
Tap on Ok, Ok. Proceed to WiFi Status, check if the status is Connected and IP Address is obtained.
Kindly try to use Internet Explorer to surf the internet"
and started the Wi-fi but it would not go on it showed Wi-fi off instead of the routine radio off.
When if went to Wi-fi => about. It showed Driver: Wi-fi not enabled, Firmware Version: Wi-fi not enabled, MAC Address: Wi-fi not enabled.
I tried the hard reset also yet the Wi-fi would not turn on.
So I reinstalled latest version 20060426-mot0822 of the Atom and before I did activesync I ran the Wi-fi and it worked well . After the first Activesync the same problem started.
For Activesync I am using the new version 4.5.0, Build 5059, Beta taken from the Microsoft site where it has the facility to keep on the Allow wireless connection on device when connected to the desktop yet the Wi-fi switches off.
There seems to be a problem with you software and your technical department needs to study it deeply and provide a suitable solution for it
Will it be the same if we will to connect to the internet in a hotspot area???
Dude i had the same problem..use the wi fi companion program i got off the net (illegal srry cant post it here)..it has fixed all my wi fi problem.
pocket msn
When I access my wifi... I can surf my internet but I can't sign in my pocket msn messenger. How shuold I fix it?
hsanghavi said:
I tired it but it would not turn on. I can turn on and off the radio or the bluetooth but the wireless. Would not go on. So I tired through Settings as mentioned before but that too does not help. Please tell me what I can do?
Click to expand...
Click to collapse
Wifi doesnt work if you are using the usb port as it will connect to your computer. I guess that is the problem for you?
Related
cld anyone plz help me in connecting xda exec to WiFi. I have Netgear : DG834G and the router configrations are shown in the picture
under > CONFIGURE WIRELESS NETWORKS
i can see the available network named NETGEAR ----- which is the name of my wireless router,but it keeps displaying connecting/available only.
if there is any step by step instructions in the forum plz give me the link
many thanks
Check you've got the following settings in "Configure Wireless Network" on your Exec:
General tab:
Network name: NETGEAR
Connects to: The Internet
Network key tab:
Authentication: WPA-PSK
Data Encryption: TKIP
Network key: [whatever it is]
Also, make sure your WiFi network adaptor in your Exec is configured for static or dynamic IP, whatever your network router is set up for.
On this site i found a possible sollution for a WiFi network tool for you PPC
http://www.cirond.com/pocketwinc.php
[/url]
On this site i found a possible sollution for a WiFi network tool for you PPC
http://www.cirond.com/pocketwinc.php
Don't forget to reset your access point. Sometimes a simple reset takes care of the connection problem.
WizzarD-me said:
On this site i found a possible sollution for a WiFi network tool for you PPC
http://www.cirond.com/pocketwinc.php
Click to expand...
Click to collapse
Does it work on the HTC Universal?
Yes the software is written for PPC. And the screenshots are windows 2003.
It should work on HTC Universal. I'm testing the software now. (only 9 Euro's) It should create more overview when configuring the WiFi network.
Benefits of pocketWinc:
Get Connected Fast
One Touch Web Browsing
Manage Connection Lists
Wireless Troubleshooting Tools
Check for Internet Connections
View Access Point Status
(all rights reserved)
for more info click on the link.
http://www.cirond.com/pocketwinc.php
Sorry guys
I tried the software but it doesn't support Qtek Universal.
The tool doesn't recognize the wifi adapter. Note that i did turn it on.
I hope they will support the Universal soon!
WizzarD-me said:
Sorry guys
I tried the software but it doesn't support Qtek Universal.
The tool doesn't recognize the wifi adapter. Note that i did turn it on.
I hope they will support the Universal soon!
Click to expand...
Click to collapse
Hi WizzarD-me,
If you are looking for a WiFi scanner. Try WiFiFoFum, it works great on the Universal.
http://www.aspecto-software.com/Forum/viewtopic.php?t=311&postdays=0&postorder=asc&start=30
Refer to mine, I have the Netgear router using a jasjar.
I dont use the WPA-SPK, I use the 64bit WEP encryption, and have provided the settings on my router and on my JJ, hope they help.
If you need further help directly PM me and we can use messenger by my screen shots should be self explanatory.
If you dont mind, could you let me know when you have connected and retrieved so that I can make appropriate edits to this post.
Attachments deleted subsequently....
cktlcmd said:
WizzarD-me said:
Sorry guys
I tried the software but it doesn't support Qtek Universal.
The tool doesn't recognize the wifi adapter. Note that i did turn it on.
I hope they will support the Universal soon!
Click to expand...
Click to collapse
Hi WizzarD-me,
If you are looking for a WiFi scanner. Try WiFiFoFum, it works great on the Universal.
http://www.aspecto-software.com/Forum/viewtopic.php?t=311&postdays=0&postorder=asc&start=30
Click to expand...
Click to collapse
Update
I was thinking. Since the option for connecting to the internet automaticaly does not indicate a WiFi connection... the PocketWinc program didn't find the WiFi cause i had my phone connection online.
After closing the program and turning of the phone connection and enabling the WiFi connection the program recognized the WiFi antenna.
Still experimenting with it at home. It has a Wifi Sniffer option in which you can set a WiFi sniffer interval. The program remembers the networks and you can set you favorites and even remember the settings on those.
The reason i set this program on this post was and still is for the overview of settings the program provides. You can sellect the network SSID and create a report of the IP configuration. There are several other interesting options like ping, trace route and more.
PS thanks for the link. I will check the WIFOFUM thingy
If anyone has the time could they help
I need someone to talk me through wifi..
I have xda exec but cant seem to get connected via access point..
I have installed the above software and wififofum. but nothing
Please help
router to have;
- ssid created, suggest a family name or similar, broadcast it
- dhcp enabled and auto control
- enable wep encryption (128 or 64 bit)
- use a shared key 9usually a choice of 4, pick one)
universal needs:
- wifi turned on!
_ start - settings - connections - network
- ypu should see it searching, cancel auto detects, do it manually
- in connections, add
- insert info above
* ssid
* choose wep encryption, shared, remove auto, enter the choosen key, txice
* slect and tell it which key number you chose (eg 1-4)
those are my settings to get it working initially
You can later if you want disable your dhcp, dns, wins n stuff
you may want to consider stopping broadcasting ssid later to prevent people looking for the network, but the wep key encryption should prevent all but the most enthusiastic genius from using the network.
this works on my netgear system.
I have a MDA PRO
Rom Version: 1.12.42 wwe
Radio : 1.08.00
Protocol: 42.41.P8
Ext rom: 1.12.126 WWE
What I want to do: I am trying to connect to the internet using pocket internet explorer using my wifi network at home and not GPRS.
The problem: I go to 'Settings' >>"connections" tab >> 'Network Cards'>> "wirelss" tab
It displays my wifi connection and it says "available" so I {tap and hold} and select 'connect'. It then states that it is 'connecting' but it doesnt connect and reverts back to saying that my network is "available'.
What am I doing wrong? Do I have to set up something on my pc? Any additional settings on my Universal that i should initiate?
I tried searching the forum with no luck in finding someone with the same problem. Is there a thread with a guide that can help me out. Thanks for your time.
soft reset the phone
then no need to go into settings
on today screen (main screen) touch the "G" at the top
it will ask you if you want to activate wifi
select
it should connect automatically
I have exactly the same problem with my M5000.
Can anyone help?
Are your home wireless networks protected (eg WEP or WPA) ? If so - and I would hope so - then are you using the applicable WEP/WPA settings and key when trying to connect ?
Worth also trying to set the IP address manually on the PDA, see if this helps ?
For me, the first thing to do when experiencing wireless probs is to temporarily disable any encryption and see if it works then.....and then re-enable, carefully inputting key etc.
Are your home wireless networks protected (eg WEP or WPA) ? If so - and I would hope so - then are you using the applicable WEP/WPA settings and key when trying to connect ?
Worth also trying to set the IP address manually on the PDA, see if this helps ?
For me, the first thing to do when experiencing wireless probs is to temporarily disable any encryption and see if it works then.....and then re-enable, carefully inputting key etc.
Are your home wireless networks protected (eg WEP or WPA) ? If so - and I would hope so - then are you using the applicable WEP/WPA settings and key when trying to connect ?
Worth also trying to set the IP address manually on the PDA, see if this helps ?
For me, the first thing to do when experiencing wireless probs is to temporarily disable any encryption and see if it works then.....and then re-enable, carefully inputting key etc.
Are your home wireless networks protected (eg WEP or WPA) ? If so - and I would hope so - then are you using the applicable WEP/WPA settings and key when trying to connect ?
Worth also trying to set the IP address manually on the PDA, see if this helps ?
For me, the first thing to do when experiencing wireless probs is to temporarily disable any encryption and see if it works then.....and then re-enable, carefully inputting key etc.
What happened there ! :roll:
On the Blue Angel, it was simple - you just set up a new connection, enter the PSK, connect and off you go!
On the Universal, however, I'm having no joy. I've set up the WEP and PSK stuff and the PDA can connect to the network, but when I try and open IE it opens up GPRS. Also, PC Anywhere only works via USB - again, it won't connect via WiFi. I'm sure it's just a case of adjusting some settings but I don't know which ones!
Wifi Connection Problems
Hi I'm experiencing exactly the same problems trying to connect.
I have a Wanadoo Livebox and my xda exec.
I've tried with my connection both unsecured and with 128bit wep encryption using the correct wep key....I still get connecting, followed by available, repeated continuously?
I have the xda set to connect to "the internet" and the authentication to "open". Key index is 1.
Can anyone help?
Thanks
Tim
Wifi Connection Problems
Hi, Just a bit more info...
Encryption is set to "wep"
Mac address is associated with the livebox.
802.1x is ticked to use IEEE 802.1x network access control.
EAP type is Smart cCard or Certificate
Thanks
Tim
Rom version 1.13.82 WWE
Rom date 11/30/05
Radio version 1.04.02
Protocol version 42.37.P8
ExtROM version 1.13.188 WWE
I just checked (with my Blue Angel) that the router and everything else is working and I'm happy to say it all is.
I set up the new connection on the BA from scratch - WPA-PSK enabled, nice long PSK, and I'm using TKIP. Network connects to: The Internet.
This allows me to remote up to the PC via PC Anywhere, and allows me to connect to the 'Net for free via the WiFi router.
When I duplicate the settings on the Universal, neither of the above works. What am I doing wrong?
Help!
You haven't got mac address filtering enabled on your router, and have forgotten to add your Universal's mac address to the list, have you?
Cheers,
Steve.
No, it's disabled.
hehe i had this problem tonight and was going to post up.
Has your router got MAC-control or anything on it? My SSID is not set to broadcast so I put the settings in manually.
I deleted the settings, and put them in manually again a few times, making sure I had the encryption stuff set correctly.
Eventually it connected and now seems to be working fine.
JAmes
Ad Hoc?
Ok, I've tried every possible combination possible and nothing is helping. So my next question to get around this problem>>>>>>>>>>>>>>>>>>>>>>>>>
Can I use my pc as a ad-hoc and us it as my gateway for my Universal?
I have a pc in the office down the hall with the actually wireless router, I have a pc in my room that is accessing the wireless router from the office.
Please let 'US' know if you have tried ad hoc or if you find the right settings to connect to the main wireless router.
Thank you
I am on my wifi network typing this, and my settings show 802.1x network access control not having a tick and network adapter connected to Work......on my iPaq hx4700 before, I used these same settings as they seemed to work well, although it ran WM2003SE not WM5.....
All this said, however, but I was lucky in that my MDA Pro connected to my wifi network at the first attempt - except not with as strong a signal as the iPaq had.....
Wifi Settings
Can anyone who has connected okay, let us have their full settings, so that we can try them?
Is your Router set 802.11g only?
You need to set the router to accept 802.11b and 802.11g.
If your router will only output at 54g, you could try the hack to switch the universal to 54g. I am yet to try this so I don't know if it works.
My MDA Pro connected straight out of the box once I set the ssid and encryption.
Hope this helps
Dave
I've been on the phone talking to 3rd line support at Orange.
Basically, the guy is totally flummoxed!
After trying to talk me through the setup from memory, it seems as though a whole menu of WiFi settings has disappeared from the phone - specifically, the ones that we need! This being the case, he's going to get hold of an M5000 tomorrow and will then bell me back so we can go through the whole process together, both of us using an M5000.
One thought that did occur to me was this: I've only just (like, 3 days ago!) upgraded to the M5000 and I've taken on some kind of free Internet access scheme with my tariff. Could it be that the settings for that (that are sent by Orange in a data SMS) have knackered the WiFi setup?
I'm considering a hard reset with a soft reset before the .CAB files install but will at least wait until tomorrow.
I'll keep you all posted....
i have been trying to get my mda vario to connect to my aol wi-fi network for over 2 weeks.
i searched xda-developers.com and found a few usefull things but i still can't get my mda vario to connect to my wi-fi network
can sum1 plz help me, i'm goin mad here
Hello, did you mean your home Wi-fi network? If so I did have the same problem before, and now everything seems OK.
What I did was:
1. Upgrade the phone to the Qtek newest ROM (though I'm not sure if this is imperative).
2. Settings -> Connections -> Network Cards -> click SDIO WLAN Wireless Adapter, then roll down the option above "My network card connects to" -> The Internet -> OK
3. Turn on Wi-Fi, maximum Power Mode for best performance (at least to test).
--> The wireless connection should be established, given you've entered network key of your Wi-Fi network if there's any.
--> Run IE to test, in my case it should start connect to the internet without any problem.
Hope this helps,
PPB
i tried that (except upgrading the rom)
everything was goin fine.
i enterted the net work key
but then a message came up about "uable to obtain server assigned ip address. try again later or enter an ip address in network settings"
Hi,
Did you do so while connected with you PC? If so try remove the ActiveSync cable.
IP should usually be automatically assigned by your Wi-Fi router.
PPB
I have a cingular 8525 branded HTC TyTn and have experienced quite a lot of wifi problems. I don't know if it's me or the device or the software, but I am looking for some other input.
The problem is that if I enable wifi, it does not see any wireless networks. If I hand punch in the SSID it will go ahead and connect just fine. I can use the wireless network and everything appears great for the moment. When I'm done using the wifi and disable it in the comm manager the device still thinks it connected via wifi. IE won't try to connect to gsm automatically, it just says locating and eventually fails. The wifi antenna in the top bar never disappears to goes back to a G. The only way I've found to get it to connect back to gsm is to remove all wifi SSID settings and soft reset.
Another oddity, when I power my device on, wifi is always enabled. Is this normal?
I thought it might just be me, but a co-worker of my just got a cingular 8525 and his does the exact same thing.
Any help or insights anyone can provide would be extremely helpful.
Rom version: 1.34.502.1
Rom date: 9/21/06
Radio version: 1.16.00.00
Protocol version: 32.53.7018.01H
Hi.
Couple of points.
Yes the Wifi remains on unless you turn it off. So when you turn back on it will re-connect.
Regarding your problem re-connecting. Some people seem to find absolutely no problems connecting and others barely manage if at all to connect. There can be many different set-ups routers, settings etc that can be at fault. However in your case when you clear out settings and start afresh all works well. I suspect an issue with renewing the the IP address.
1
So you could try "fixing" the IP address ie removing the DHCP dynamic allocation of the IP.
or
2
You can try "Hitchhiker" which is afreeware application that takes care of a number of background setup issues one of which is automatically re-assigning the IP address. (also allows cutting and pasting the WEP key if you use it - saves a lot of typing).
I use this app with mine whenever connections are sticking. I let Hitchhiker sort things out and then I turn off hitchhiker wich disconnects me, but then I find the normal way of connecting me works fine. Of course you can use Hitchhiker routinely to connect and it does make things easier if your connecting to Hotspots etc.
Hitchhiker is available here as is .net compact framework 2 which is required for it to work. Some people seem to have difficulties with Hitchhiker but it's always worked perfectly for me after a soft reset with my device.
http://www.kasuei.com/hitchhiker/
Mike
I had a number of connection problems with APs whose encryption was set to WPA/WPA-2 (dual mode WPA) as opposed to WPA or WPA2. Switching the AP to just WPA fixed the problem as WM5 doesn't support WPA2.
Speaking of which: does anyone know if Crossbow has WPA2 support (when it was released for XP it was freakin' huge so I'm not expecting anything here).
As for the WiFi connection being persistent in PIE and other apps even after it's been disabled: check the connection setting for your AP profile (Comm manager>WLAN settings>Menu>Network Cards) see if the 'connects to:' setting is on 'The Internet'.
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
dtran707 said:
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
Click to expand...
Click to collapse
Try to set wifi to best performance instead of best battery first.
Often the problem is also caused by a combination of the router (brand/type) and a Windows based device/computer.
Some things you can try to get a working connection with WPA-PSK enabled:
1. Modify the registry:
\HKLM\Comm\EAP\Extension\25\ValidateServerCert=dword:00000000
2. Modify the network settings:
Settings > Connections (tab) > Wi-Fi > Network Adapters (Tab)
and select "NE2000 Compatible Ethernet Driver" (maybe you have to config a static ip-address).
Thanks for the suggestions. I did all those, except for the static IP since our network admin doesn't provide one. It still doesn't work. One thing I'd like to understand is that in my case, why does the WPA-PSK connection work for the standard Windows environment (laptop/netbook, desktop) but not Windows Mobile? What could be the difference?
I don´t know what ROM are you using, but if it is some of 23XXX Builds, disconnect first the Bluetooth and then connect the Wireless... Should work now...
My ROM is MK_872_05 WWE, from chota_shivaji. It uses WM6.5 CE OS 5.2.21872. Thanks for your suggestion. I will try it out on Monday when I get back to work.
I disconnected the Bluetooth connection and tried again to the WPA-PSK encrypted access point at work and it still doesn't work. Just yesterday at a relative's place, I was able to connect to his router with WPA security. I think there's something different with the one at work which does not work with Winmo devices.
at work do u just have a password or a user/password? are u using certificates?
At work I have a guest username and password that I can use to log in for the WIFI access point. The password changes every week, but I confirmed that I used the latest one. But I don't think there's a certificate needed since my co-worker is able to use his home netbook to log in without anything else except the same username and password.