Siemens SX 56
I installed the "XDA developers special edition ROM".
I did set the settings on my provider "O2-Germany" when the SX56 started.
The phone is now "unlocked".
My SIM card was detected, I entered my PIN.
I still get no signal. (using the phone is impossible)
What should I do?
Related
I upgrade my ROM to Pocket PC2003 (T-mobile.nbf) image that worked with no problems using the XDA OS Image tool. It copied over using programme A and following the upgrade I carried our a Radio Stack upgrade to 4.21 supplied by O2. I now have a problem as the phone wont work. I tried re copying the immage again but just before programme A runs a cmd.exe box apears and I get the following message 'ERROR: GetConnectionType - An existing connection was forcibly closed by the remote host.
error getting connectiontype
Programme A then tells me my device is not connected and to check the USB connection. Can any body please help me. All I want is to get my XDA phone up and working again.
Which network are you using, it may be that the bandswitch has chosen 900/1900 which would prevent orange and t-mobile from working, if this is the case enter bootloader, then push the key below the antenna, choose 900/1800 then reboot.
I'm on the O2 (pay as you go) network. There were no problems with my phone and the T-mobile image until I performed the O2 Radio Stack upgrade. I hade already performed this upgrade on my old operating system, before I copied over the T-mobile image. I had no problems with the old OS and the Radio Stack upgrade.
Seamus, if you burn the original O2 rom back to the phone, you will be able to return it to O2 if it is the radio stack upgrade that killed the phone, they should fix it for free.
Hello guys Need some help from the pros
I currently purchased this phone its a Siemis Sx56 AT&T. As i was updating 2 unlock the phone with a dump of another sx56 aT&T that was uncloked (via sd card) it stop in the middle of the proces of uploading the boot of the sd card. Now the phone:
1. Will not start
2. Can not boot the phone to wallaby
3. cooked a rom and tried 2 boot 2 wallaby with no luck
4. 1/2 read & read with no way of knowing what i'm doing wrong
5. how can i repair my bootloader (I used the one in xdtools with no luck)
Than U guys in advance
Luv the Info in the forum.
Adrian
Atlanta GA USA
Hi there,
I have my SIMLock Code for my Voda v1640, and I put in a Virgin SIMcard, entered the code, and it said "SIM Unlocked" and then worked great.....
Just wondering, do I need to keep my SIMLock code handy (I have it on an SD card at the minute) if I use a different SIM (ie try and use an O2 SIM) or does entering your SIMLock code completely remove SIMLock and never have to be entered again?
TIA
Hi, I just got my O2 Mini S from a seller. (WM5 IPL 2.21.0001)
But, when i put a 3 sim-card in, it told me that the sim-card is invalid. But it didn't give me a place to input the unlock code.
After i run the okiwizMSL0.2b program, the MiniS restarted so quickly, that I couldn't have time to remember the unlock code. Then I insert my 3 simcard. It still tells me that I am using an invalid sim.
Then i put an O2 simcard in, it is working.
Any suggestions will be highly appreciated. Cheers
Hi,
I have an XDA Orbit. Everything works ok except when I try to use the phone, It searches but cannot find a network. The inserted SIM is o2 Pay&Go. It does ask for my pin on startup and can read the SIM history but when I try to call, the calls ends after about 2 seconds and it comes up with the following error message:
"Cannot complete the call. The signal may be unavailable or the phone number may be invalid. Verify the number and try again later"
The SIM is ok as I have used it in another phone.
Any suggestions guys...
Regards
Brian
is the phone blocked by o2? if not try flashing an official o2 rom
Not sure if it is locked to o2, I have tried the o2 SIM and a T-Mobile SIM but both give the same result, unable to find network.
I have flashed it with the official o2 WM5 rom and the WM6 upgrade and I ahve tried a different radio firmware but same result...
I would welcome any further suggestions.....
Try engineering mode with GSM reset
Hi,
Thanks, I have experience of successfully flashing the orbit but "engineering mode with GSM reset". Some help please as to how I do that.
Hello all,
I have a T-Mobile MDA Vario (HTC Wizard) that I've been using on the Hutchison Network in Austria. The Phone was CID and SIM unlocked by me 1 year ago.
Suddenly the phone no longer recognizes the SIM card saying "missing or invalid SIM".
I tried the SIM in another phone and it works fine. I tried also a T-Mobile SIM, same problem. I did a soft and hard reset but still no luck. I tried also to lock and unlock the SIM using Wizard Service Tool, still the same problem. Wizard Service Tool shows CID unlocked and SIM unlocked.
I tried also Button's 1.05 ROM, same problem.
Any Ideas??