Ok so I trashed my ppc doing the radio update. Since I did the exact thing that Freshster did here is a cut and paste of my problem
" So, I tried running this TMO 4.00.10 upgrade in order to upgrade the radio stack to 6.24.00. While it was doing the radio stack upgrade, it failed at 13% complete. The error told me to "reset the device normally, wait for the radio stack to repair itself, reset the device again normally, then try to run the upgrade again."
After I did the normal reset that it told me to do, my screen got stuck on the ROM Kitchen boot screen and only showed a G, R, and 4.00.05 at the bottom corner, without showing a radio version or protocol version number. The led would not light up anymore. It did not flash green to show that it had signal, and it would not even show orange when it was connected to a charger. "
At this point Im SOL until tomorrow b/c I dont have a SD reader, my question is, can I upgrade the radio via the SD and hopefully get things going again? Or do I just attempt to reload a whole new rom and rsu via the SD card tomorrow. Thanks in advance for your help.
This is just a suggestion, I don't know if it will work.
1. Bootup in the Wallaby Boot Loader (hold power button while soft reset)
2. Press Calender button to bring up radio stack selections
3. Select turn off GSM
4. Reset and see if it will boot up when it doesn't have radio turned on
5. If it will, then set in active sync in guest mode
6. copy the RSUpgrade files to your window directory on the device using the explorer option in active sync
7. copy the two monitor files monitor_ul_bs.map and .m0 to the windows directory
8. reomove the device from the active sync
9. using the explorer on the device find the RSUpgrade executable in the windows directory and double click
10. this should start the radio upgrade going again
GOOD LUCK!
Thanks for the suggestion, I tried it but now luck. The pda stays stuck on the rom kitchen boot up screen. Thanks again.
OK, I had the exact same problem. You have to be patient, when you reset the device you'll get the R blank / G blank because the existing radio stack has now been trashed. eventually the PPC OS will boot. At this point reset again, wait for CE to boot & then reset again, The point is keep resetting the PPC every time you get the R Blank & G blank screen and wait for CE to boot. ON each reset the radio stack upgrade is working in the back ground. After 4 or 5 resets mine came up with R 6.24. at this point I connected the PPC back to Activesync & reran the upgrade & it went through just fine & installed the T-Mobile WM2003 ROM
Pdageek1 is right on the money! But I'll add one more step, remove your SIM card. HTH
I will try this on my way to work. I have another question, is the unit still charging when its on the base even though the charge light is not on? Thanks
I had same problem, if you flash with old t-mo rom it boots up everytime and will allow you to reflash radio stack.
http://www.t-mobile.com/pocketpcupgrade
hello pdageek and thanks for the suggestions. I have left my unit on at the splash screen with the blank g and r for about 5 2 minute sessions with no luck. Im hesitant to leave it on too long and have it eat up my battery. How long in total did it take your pda to boot up with the corrupt radio upgrade?
Sirseymore, the problem I have right now is that I cant even get it past the splash screen, since the OS is not booting up I cant see the unti via active sync.
You can't just it leave setting there with the blank screen you have to keep
doing the soft resets, until it boots!
Also to speed things up a bit during some of your soft resets try holding the volume control button, it similar to holding the hand of a sick person.
I know it sounds funny but hey what the hell, I did it! :wink:
One last note it also might help if you do a hard reset while holding the volume conrol buttom. I know that also sounds funny but hey I did that too! :wink:
HTH
Thanks for all your suggestions everyone. I ended up loade the latest tmobile rom via the loader, I let the pda sit at the Tmobile splash screen for 15 minutes until it booted into CE. Next I copied the necessary files for the RSU into the windows folder, ran the executable and all is working now.
Once again thanks for all the great people in this forum.
bimmer10 said:
Thanks for all your suggestions everyone. I ended up loade the latest tmobile rom via the loader, I let the pda sit at the Tmobile splash screen for 15 minutes until it booted into CE. Next I copied the necessary files for the RSU into the windows folder, ran the executable and all is working now.
Once again thanks for all the great people in this forum.
Click to expand...
Click to collapse
When you say Latest tmobile rom do you mean the 4.00.10 or the latest rom off of Tmobile's Website?
I got the same problem as you did blank g and r
Let me know Thanks, Allen
I'm in the same boat. I was running 4.00.05/stock 6.18 RS on T-Mobile USA.
I decided to try to do the Radio Stack upgrade by copying the extracted rsupgrade and monitor files to the device, and running them. It hung at 13%, so I soft-reset, and it hung at the blank G, blank R, 4.00.05 screen.
I tried turning GSM off in the bootloader, and have removed my SIM card. No luck.
Then, I flashed to the 4.00.10 ROM via bootloader, and I'm still sitting at the G/R screen. I have soft reset a few times, but that hasn't gotten me anywhere. I haven't left it for longer than 3 minutes or so before I get so anxious that I try another soft reset.
There seem to be two bodies of opinion here - those that say you should keep soft resetting until CE boots, and those that say just to leave it and wait for CE to boot (15+ minutes).
Is there any consensus among those that have recovered from now-infamous blank G/R screen? Should we wait, or should we keep soft-resetting?
JoshB said:
I'm in the same boat. I was running 4.00.05/stock 6.18 RS on T-Mobile USA.
I decided to try to do the Radio Stack upgrade by copying the extracted rsupgrade and monitor files to the device, and running them. It hung at 13%, so I soft-reset, and it hung at the blank G, blank R, 4.00.05 screen.
I tried turning GSM off in the bootloader, and have removed my SIM card. No luck.
Then, I flashed to the 4.00.10 ROM via bootloader, and I'm still sitting at the G/R screen. I have soft reset a few times, but that hasn't gotten me anywhere. I haven't left it for longer than 3 minutes or so before I get so anxious that I try another soft reset.
There seem to be two bodies of opinion here - those that say you should keep soft resetting until CE boots, and those that say just to leave it and wait for CE to boot (15+ minutes).
Is there any consensus among those that have recovered from now-infamous blank G/R screen? Should we wait, or should we keep soft-resetting?
Click to expand...
Click to collapse
Well i just got mine working FINALLY, what i did was flashed the rom to 4.00.10 and then did a soft reset let it sit for 15 minutes and then it came to the Align screen blah blah blah So just be patient and let the device sit for 15 minutes or so
Good Luck
Reflect said:
Well i just got mine working FINALLY, what i did was flashed the rom to 4.00.10 and then did a soft reset let it sit for 15 minutes and then it came to the Align screen blah blah blah So just be patient and let the device sit for 15 minutes or so
Good Luck
Click to expand...
Click to collapse
I let mine sit, and after about 15 minutes, it did finally come back up. I was able to copy the files and manually run the 6.24 RS upgrade, and I think everything is going to be OK now.. *crosses fingers*
I let mine sit, and after about 15 minutes, it did finally come back up. I was able to copy the files and manually run the 6.24 RS upgrade, and I think everything is going to be OK now.. *crosses fingers*
Click to expand...
Click to collapse
Well mine is working very good i havent came acoss any errors yet All i did was do the regular upgrade to 4.00.10 and got to 13% on Radio Stack Upgrade when it errored so i took it out did a few Soft Reset's no luck so i flashed the 4.00.10 Rom through the wallaby bootloader got it up waited patiently for CE to load... loaded after about 15 minutes at that time it was running terribly slow and when i got it up i had no service because i had no Radio Stack so i then loaded up this old radio stack well not so old but it was version 4.21 i then soft reset the device started the 4.00.10 install it went through the Radio Stack then the Rom update with absolutley NO errors or conflicts so everything is working great..
Heres something to keep in mind DONT Upgrade To Tmobile Rom 4.00.10 With the radio stack version A.20.10 Or you will be doing what i had to do!
i want to say thanks to all the great people out there posting
Thanks, Allen
JoshB said:
There seem to be two bodies of opinion here - those that say you should keep soft resetting until CE boots, and those that say just to leave it and wait for CE to boot (15+ minutes).
Is there any consensus among those that have recovered from now-infamous blank G/R screen? Should we wait, or should we keep soft-resetting?
Click to expand...
Click to collapse
My suggestion is this when you're in deep dodo, try it all! :wink:
Because as your seeing what works for some doesn't always
work for others.
Reflect, sorry I wasnt able to answer the specifics of the rom earlier, I was talking about th 4.00.10 version. Im glad you were able to fix the problem. :wink:
After waiting the 15 minutes to recover from the blank G/R screen, and successfully upgrading the Radio Stack to 6.24 and the ROM to 4.00.10, I've been using it for a day or so now, and I am pleased with the new ROM and radio stack.
Biggest plus for me is that GPRS now stays "always-on", even when the unit is turned off/suspended. I also like the fact that AIM 2.0, and PDF/PowerPoint viewers are included in the ROM.
As far as stability, I have had a couple of lockups (cleared by soft resets), and one spontaneous soft reset, but these could have been caused by software that I have installed (SpB GPRS Monitor, StocksAndWeatherToday, Journal Bar, Battery Bar, PocketNav, AE Uptime, Fonix VoiceDial Premium, Resco Explorer 2003).
I have had a couple of instances where the GPRS connection stops transferring any data, but still shows as connected. Since there's no way to turn off GPRS (SpB GPRS Monitor has a Disconnect button, but it doesn't seem to work), I can clear this condition by turning the phone off (not the unit, but the phone/radio) then turning it back on and reconnecting GPRS.
Thanks to everyone on this forum for your help, support, and ideas! This is a great amateur developer community.
JoshB
P.S. - Reflect, sorry I didn't answer your IM. I was in bed...
OK, I am going to try this once more since I can't stand having a useless phone...lol
I *had* the 4.00.05 ROM and the newest at&t radio stack on my T-Mobile phone (with TM service).
Attempted to install the T-Mobile 4.00.10 rom and associated radio stack via the .exe method over that, and it failed.
After that, I tried reverting back to the old T-Mobile 3.14 rom, via the sd card method. That seems to have loaded, but the GSM is still screwed.
Currently, when I start up the phone, I get the Welcome to T-Mobile startup screen, with 3.14 in the bottom corner. After a minute the G with no number after it is there, and below that, instead of an R is a U? (Maybe because I don't have the sim card in?) With no number. Then I get the "bing" sound, and it goes to a blank screen.
Reading through the posts here, it sounds like I should write the 4.00.10 ROM to the unit with the SD card, then wait for it to start up?
Should I have the sim card in?
When should I try the soft-resetting?
Just as an update, so far so good. I wrote the 4.00.10 rom to the unit with the sd card. Did a hard reset like it told me to. Now starts up with the T-Mobile Test only Not for sale screen. Shows 4.00.10, G with nothing after it, and R with nothing after it. It now stays at this screen though, instead of going to the blank screen. I guess this is a good sign, I am in a position others have been in. Yay! Waiting on it now to do something...anything, and I will attempt the radio fix.
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
OK I am stuck at the screen showing IPL SPL GSM and OS.
I was wanting to change the ROM so I used Resco backup and made a full backup.
Then I flashed back the original Rom for my Cingular 8125 / HTZ Wizard
Then I flashed to HTC Business Edition ROM CE OS 5.2.1622 Build 18128 AKU 4.4 http://forum.xda-developers.com/showthread.php?t=376667
Then ran my restore but since I forgot to put in my name and other personal info it said some stuff couldnt be restored so I Put in all my info and then did the restore again and it said it was complete and needed to soft reset so I said ok and now Im stuck at the boot screen like I said.
Since Im at this spot active sync wont connect and I cant reflash that way.
any help or ideas would be appreciated.
Cheers,
Chris
I am sort of in the same boat, got the wizard flash with buttons image, but now it won't connect via activesync, hopefully we will both get an answer.
cholubaz,
I got my problem solved by ....
1) doing a hard reset on my phone
2) un-installing active sync AND deleting the active sync folder then re-installing a fresh copy
I wanted to pull what little hair out that I have left, but it all came out good.
I fixed mine too just a few min ago
Mine wouldnt even hard reset. Holding the Power button down did nothing no matter how long I held it down.
I took the battery out and put it back in after a few min to a few hours and still it would only boot to the same screen I mentioned.
What I found out was that if I held the camera button in and then turned on the phone I was able to get in to boot loader mode and then I was able to reflash to a new ROM.
So Im back in business now
Cheers,
Chris