i know this out there in the forum but i can't find. how do you re-install microsoft voice commander 1.5
Have a Problem Installing Microsot Voice Command Version 1.5 Upgrade ??? Read This!
--------------------------------------------------------------------------------
If you are trying to install the upgrade to Microsoft Voice command version 1.5 from http://www.microsoft.com/windowsmob...ateversion.mspx for your Pocket PC or Pocket PC Phone and an error message on the desktop that
“No previous version of Microsoft Voice Command US PPC 1.50 was not found on this machine. The setup cannot continue” and you do have version 1.0 or 1.01 already installed, I would suggest the below mentioned steps .
1. On the Desktop, to go Control Panel --> Add/ Remove Programs --> Look for Microsoft Voice command US PPC 1.5. Typically you would have two instances of voice command here, the other being Microsoft Voice command, which is the version 1.0 or 1.01 and the qualifying product for the upgrade which should not be uninstalled at this point.
2. Now, highlight only Microsoft Voice command US PPC 1.5 and then click remove. This install size should be around 0.09 MB or 0.07MB due to incomplete install previously.
3. Now uncradle your pocket PC / PPCPE, Tap Start --> Settings --> System Tab --> Remove Programs, If you had installed Voice command 1.01 on the Pocket PC phone.
4. Highlight Microsoft Voice command, then Click Remove in the Pocket PC. Once the software is removed from the Pocket PC and you removed the listing of Microsoft Voice command US PPC 1.5 on the desktop in the control panel.
5. Cradle your Pocket PC again and synchronize. Now run the Microsoft Voice command 1.5 Upgrade setup file which you downloaded from the MS website once again and perform the actions displayed. This should install the Voice command upgrade to V1.5 on the Pocket PC device successfully.
Hi all,
I did the bigstorage and my qtek (which is excellent) but the problem is that voice command didn't work anymore. So i uninstalled it but impossible to instal it now on my Qtek. It stops during the installation and says "Microsoft Voice Command hadn't been installed. Start the installation program again" or something like that (it is written in french..)
Maybe anybody can help me to resolve my problem (without doing a hard reset...)
Thank you
I had the same problem with Microsoft Voice Command 1.0, I just done and uninstall and installed Microsoft Voice Command 1.5 and worked fine
Brian
1.5 works fine over here as wel!
brian colston said:
I had the same problem with Microsoft Voice Command 1.0, I just done and uninstall and installed Microsoft Voice Command 1.5 and worked fine
Brian
Click to expand...
Click to collapse
That is what i did (i installed the 1.0 and uninstalled it) but the same problem...
Have a problem, I´m not able to install MS voice command on my 9100.
No problem with S100 runnin W2003.
But Is it it compatible with w2005?
Every time I try to do this is says: cannot install.
Why?
Please help, really want it on my 9100!
which version of voice command are you trying to install?
1.0, and then upgrade to 1.5..
That´s the only files I have. But I cannot get 1.0 to work, so its pretty hard to upgrade to 1.5...
But it worked to do this on S100
I had the same issue. I dont have it in front of me, but here's the process.
Install version 1.0. In the activesync application manager, uncheck version 1.0 so that it uninstalls from the PDA but not from the desktop. Install version 1.50.
After it goes through its install process, make sure that its checked in the activesync app manager.
Hope this helps, I had to do it a couple of times, (check version 1.0 to install, then uncheck again).
cnegron said:
I had the same issue. I dont have it in front of me, but here's the process.
Install version 1.0. In the activesync application manager, uncheck version 1.0 so that it uninstalls from the PDA but not from the desktop. Install version 1.50.
After it goes through its install process, make sure that its checked in the activesync app manager.
Hope this helps, I had to do it a couple of times, (check version 1.0 to install, then uncheck again).
Click to expand...
Click to collapse
Thx so much.. had to install, uninstall about 30 times, but now it works!!
Txh!
Hi!
I've tried voice command 1.5 on a qtek 9100 and it is really slowing everything down so much I had to turn it off. Starting programs, switching between them and using any program is a real pain with Voice Command enabled :-(
Does any of you have the same problem?
Regards,
// aste - writing this on the phone
Sorry no problem for me on a Qtek 9100...
I had Voice command 1.5 on my Magician (MDA Compact) which worked fine, I put it on my Wizard (Vario) and it was slowing it down so I transferred it to Storage card and it appears to be better. Only problem is on soft rest it says voice command cannot be found and you have trouble removing the warning box it sticks around for ages. When installing it also says...won't work properl on storage card, put on phone or something, but it works just fine.
monkeyphonix said:
I had Voice command 1.5 on my Magician (MDA Compact) which worked fine, I put it on my Wizard (Vario) and it was slowing it down so I transferred it to Storage card and it appears to be better.
Click to expand...
Click to collapse
I've got it installed on my Vario (on the phone) and it's not slowing it down at all.
Odd...
Cheers,
AJ
I have MS voice command 1.0 and I want to install it on my new T-mobile MDA (USA) - its running windows mobile 5.0
When it downloads the cab to the MDA, it pops up an error:
"this program is being installed to "". We recommend this to be installed to MAIN MEMORY instead. YES , NO options "
If I click yes, it installs but the program does not work.
If I click no, it does not install.
What is going on ???
Hi,
Here's Cyberon Voice Commander 2.0 (build 703231) but can only run on Dopod devices.
Anyone out there would like to try to mod it so that it can be run on every devices?
Thanks in advance.
what phone model / OS are you trying to install this onto...
I just installed it onto my IMATE JasJam with no problems... i checked the setup.dll and it has no IMEI checking either...
what was the error message you got when you tried to install it?
On WM5 AKU 2.2 XV6700 installs correctly but upon run gives "Device not supported" error.