when i try to change rom in my qtek 1010 it rebooted when progress bar was 99%. now, boot-loader is booting , but when trying fixbootloader nothing happening. on device screen - "booting...".
when trying to change rom from sd card (rom was loaded to sd card using xdatools) - on screen: "invalid sd card..."
how to fix boot-loader and change rom?
Related
i have Qtek 1010 i did upgrade from PPC 2000 to 2003 in the middle of the upgrade 82% it get stuck .. now my qtek is not working ..
i have SD card .. but i dont have a backup for my previuos OS ..
any help will be appreciated..
reagrds to all
QUsai
How were you doing the upgrade, PC install or the SD card boot loader
method? If was the PC install trying using the SD card boot loader method.
For more info. on the SD card boot loader method just do a search on the subject in this forum.
HTH
I was upgrading the ROM on my SX56 from AT&T so that I could use my T-Mobile SIM card on it and unlock the device.
Unfortunately while upgrading my PC crashed and now my SX56 is dead and when i power it up I get the message :
Upgrading
It will take about 5 minutes...
I dont have the backup of my ROM on the SD card..please help.
I have a 64MB SD card and card reader also. I made a mistake of not taking the backup. Please help to get my phone running ..I just purhased it for $200 and now its dead.
get a rom and use xdatools to flash it to the sd and flash the xda using the bootloader
I got trouble - I tell you....
Yesterday, I wanted to update my T-mobile MDA from winmobile 2002 to 2003. I was using "Lumpistefans" -Romkitchen (xda.weblink.net). I choose the rom to be coocked as an "installer exe".
When I performed the update, everything worked fine - for about 30 secs....then brakedown
This message accoured "Can not open COM/USB port...."
from this time on, my mda seems to be toasted!! I can't switch it on , softreset won't work - and after an hardreset the display only shows some black stripes and two blank squares at the top half.
I don't need to mention, that Activesync isn't recognising the mda anymore - saying "uknown usb device - can't connect"
I don't think the Bootloader is working still either - by pressing the on/off button, the bootloader should be activated ..or??!? I never tried that before.
I read the thread "rom flashing is dangerous" but didn't get any helpfull info on my case.
I need Help...getting quiet despered!!
THANKS for alls Help , Hints and comments!!!!!
ciao
mark
here is how you enter the bootloader
http://xda-developers.com/bootloader/
ok thanks - the bootloader is still working ... can i now just flash it with a rom using my sd card?
yes just plug in the sdcard of min 64MB into your sdcard writer/reader and use xdatools to flash the nbf or nb1 file to the card
and put in the sdcard and go back into the bootloader
I was updating my new i-mate SP3 (typhoon) to the latest i-mate ROM 2.4.33.11 which completed successfully but now every time I turn on the phone it goes directly to the bootloader tri-color screen. I tried several times to update the ROM again but it does'nt help. It shows the proccess completed successfully but the phone is still stuck in bootloader mode.
In the bootloader screen it shows the following
IPL 1.00
SPL 2.5.0102
I even tried to flash the ROM through an image of Orange4114_ALL_SPL1010091 on a miniSD card but it gives an error message
"Not allowed update!"
Please help me figure out how to get my phone working again.
Same PROBLEM here HELP..!
Exactly the same problem if anybody can help ..please do.
spl
hi
same problem my sp3
SPL
Same problem on spv c500 stuck in bootloader but with 2.05.0130 SPL
sp3i stuck
Hi all,
I have the same problem, but I didn't try the mini-sd boot.
surfturtle, will you kindly send me the way?
Thanks
Hi guys...
I don't have the Typhoon and don't know if this will work for you, but this is at least how we fix this problem on the Hermes:
Enter into bootloader using mtty.exe and run the command "set 14 0" and "task 8". Phone will reboot and start OS.
If it doesn't work, then try the SD flash method mentioned by surfturtle. Keep in mind that if your device is not superCID the image file should match the CID of your phone (must be an original shipped update from your vendor). This method consist on:
1) extract the rom image from the rom upgrade exe (winrar or cabextract can be used for that) and you'll find a .nbf file.
2) Rename it to TYPHIMG.nbf
3) Format your SD card in FAT32
4) Put TYPHIMG.nbf on the root folder of your SD card
5) put sd card on the phone, and enter into bootloader
6) confirm flashing on screen, and wait until the process is finished (do not reset it, will take about 30min).
Check the hermes wiki if you need more information on any of this.
Good luck!
sp3i stuck
thanks pof,
but where would I get mtty.exe and where will I see "set 14 0" & "task 8"
thanks again.
Re: sp3i stuck
@Tall_Man: See the hermes wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
I-mate ROM
Hi, I did the upgrade through the PC but the device info still shows the old ROM: 2.1.33.13 No error messages and the phone keeps hanging on me.
Is this version of ROM the Arabic one? If not, can someone post or point to where I can download the arabic version? I did not find it on the I-mate website.
Thanks in advance,
I-mate SP3 (?rom 2.1.33.13)
Hi, i tried to install touchflo on my pda phone but the instalation failed. And now everytime i try to install a custom rom or anouther rom for example: button's 1.05 ROM. The instalation totaly completes but when my phone restarts it´s gets stuck at the boot screen with the picture on a beer and the ipl/spl 1.01 shows up and there its stuck, i dont come in to windows. i have followed these guides: http://forum.xda-developers.com/showthread.php?t=298613 and http://forum.xda-developers.com/showthread.php?t=285435
But with some roms the instalation stops at 98% and a error message cames up and it says: "error 326: this NBF file can not be used for your PDA phone, please check your NBF file"
And when i try to hard reset it says: "format FAT partition and format is failed"
pleeease help me what scould i do to get my phone back to normal again?
sincerly yours// Johan
When its on the beer bootscreen, give it time. The button rom (i find) is real slow but works for what we use it for
Is your phone CID unlocked ? try to get the phone in bootloaders mode (multicolor Screen) and either flash the button's rom 1.05 or official stock rom of your carrier to recover back to default working status and download the WST tool and verify the SIM/CID lock/unlock status of the phone.If you have inserted any sdcard or mini sd card remove it before flashing.
Cheers!
skezza said:
When its on the beer bootscreen, give it time. The button rom (i find) is real slow but works for what we use it for
Click to expand...
Click to collapse
no, i have waited for 10 hours but its still stuck
zabardast_1 said:
Is your phone CID unlocked ? try to get the phone in bootloaders mode (multicolor Screen) and either flash the button's rom 1.05 or official stock rom of your carrier to recover back to default working status and download the WST tool and verify the SIM/CID lock/unlock status of the phone.If you have inserted any sdcard or mini sd card remove it before flashing.
Cheers!
Click to expand...
Click to collapse
yes i have CID unlocked it one time. but when i get the phone in the 3 colored screen but when i flash de buttons rom 1.05 and complete the instalation i get stuck in the beer screen there i can see ipl/spl 1.01 i dont came in to windows and i must come in to windows to rerun the CID unlocking or can i do that by the 3 colored screen?
pleease help me
cheers!
Got the same Problem, any ideas?
Hi Ashtrays,
could you solve your problem?
I got the same one: Flashed my MDA with a new ROM, and after a complete installation it gets stuck at the splash screen.
I flashed back to Buttons 1.05 ROM but still got the same problem: A nice beer glas and the info about IPL/SPL 1.01 and nothing more happens.
So have you solved your problem? Maybe you can help me out...
thanks
Henning
Do a Soft reset or Hard Reset,it shud work,otherwise reflash the Rom.