Since my last hard reset, I've been having error message once in a while telling me that the backup battery is extremely low (which was 100% full just a moment before) and then the PPC will freeze. It won't even respond to soft reset and I had to take out the battery to reset it. Then the backup battery will say it is 100% full again.
Could it be due to the installation of Avantgo and Journal Bar data files to the storage card that I'd done since my last hard reset? Could it be that they are not compatible with my Chinese Dopod 818?
Anyone has any ideas?
BackUP Battery Problem
I have the same problem, that is POP UP appears showing that backup battery is extremely low and then I was unable to use my stylus on the screen but button work fine.
I then installed Spb Pocket Plus 2.2 but problem remains then I remove the main battery and inserted it again . After that unit works fine and since then I have not received any error.
Asim
I know there was a thread for this a while back as I read it when searching for something else. Now I can't find that thread (the search function in forums is never great!) but I suddenly have a huge problem with the built in Alarm function on my Wizard...
I've had a few issues before where when the phone is charging overnight it soft resets by itself and then sticks on the initial O2 screen. In the morning, I disconnect the phone from the charger and the phone then boots, I enter the password and the alarm goes off (usually later than the time I set it for). This is annoying but I can live with it.
However, this morning I had HUGE problems. It did the same as usual, phone was stuck on O2 initial screen so i unplugged the charger and the phone began to boot. I entered my password and the alarm started to go off but I was unable to switch it off at all. It does not come up with 'Notification' in bottom left of the screen like it normally does when the alarm goes off. It just kept going off even when I unset the alarm. I did a soft reboot but the same thing happened again. Also, the right-hand light at the top was orange even when the charger was not connected so the phone seems to think it is charging when it isn't.
I have managed to get it to stop thinking its charging by enabling wifi for a few minutes whilst charger is connected, then disabling wifi and disconnecting charger. But, every time I soft reset, the alarm starts going off and wont stop and the orange light comes back (while not not connected to charger). Also, none of my calendar items are reminding me 15 mins before the appointment like they normally do.
Is there anything I can do? I really don't want to hard reset if possible and certainly not just to stop the alarm! I am using Molski's latest 30Mb free WWE ROM. There isn't much installed, just PocketMax PhoneAlarm (great app!), TCPMP, handy Switcher, OMAP and OMAP+, Resco file explorer and Salling clicker. But I have had these apps for a while now. There is also SoftKey which appeared after upgrading ROM and I have changed my left button (directly above the call connect button) to Notes, perhaps this is why the Notification does not come up?
It is so embarrassing that a £400 phone cannot do something so basic as waking you up at the right time
I know a lot of people have had this problem with WM5 but has a fix ever been identified? Sorry about the huge post btw but any advice would be hugely appreciated
I'd say try reflashing that ROM or try another ROM...
The $400 phone was designed to work with the ROM from the manufacturer and MO that it was sold under... If the problem still persists under those circumstances than the problem is most likely hardware related and you should be seeking a warranty repair (if that option is avalible to you). Although, you were made aware when you loaded the cooked ROM that it could cause you problems and voids any warranty.
I had the problem (although not as severe as today) when I was using the default ROM that was installed from the phone company...
Also, from the last thread about this it seems a large number of people with different ROMS/devices have had the problem...I'll reflash if I have to but I'll try a hard reset first....
try removing phone alarm and see how it will now behave.
Read my post in this thread http://forum.xda-developers.com/showthread.php?t=275189
Thanks meschle, I think it's fixed, I had to soft reset then delete the notifications several times, but now it has stopped sounding the alarm every time I soft reset...
Saved me a hard-reset - much appreciated
on my Tytn it says "Clearing Duplicate Events Processing 67 of 66 events" and basically stays like that.
Any ideas?
warmkiwi99 said:
on my Tytn it says "Clearing Duplicate Events Processing 67 of 66 events" and basically stays like that.
Any ideas?
Click to expand...
Click to collapse
Hi it froze - try deleting the duplicate notifications one by one (click on the notification in question) or try trial version of memaid http://www.pocketgear.com/software_detail.asp?id=14279
got a htc phone and my phone keeps freezeing i need to take the battery out then put it bk in to get my phone it keeps happening alot. took it to a shop and they say they reflashed but it didnt work any body got any ideas thanks
First of all, while the phone is working.. BACKUP all data.
Then try this...
Hardreset (I don't see any other solution).. then RESTORE data.
If the above post doesn't work, then maybe you should have that unit replaced while it's still under warranty (I assume)...
I also experienced the same a while ago. All of a sudden, after 2 weeks of using, it hung. The only thing I did was having it a day connected to the internet and loading 150 emails into the newly created account. I experienced a slower operating system, though, and the hanging of the Jade could be linked to this full inbox.
Btw. no additional software installed or tweaks. At that time, I only had NoData installed and TomTom.
For some reason, when the backlight went off, the wake up hard button on the Jade didn't function either, so I had to take out the battery every time to make a call. Rediculous...
The solution for me was indeed to hard reset. Soft resets or configuration chagnes didn't work. After the hard reset, no problems anymore...
My battery was running low and when I got home to a charger it was dead. Started to charge it up and after an hour or so switched on and got the following error message:
\..\common\persistence\internal\winmfile.cpp.56
When I clicked Ok to clear, it suggested I need to hard reset my device. I removed battery and tried rebooting several more times, but the same error kept coming up so in the end I had no choice but to perform a hard reset
Has anyone else experienced this error or know what may have caused it?
It was strange seeing my HD2 in the 'out-of-the-box' condition with no tweaks. Luckily all my .cab files were on memory card so had spent rest of day installing all my tweaks/programs again!
*bump*
anyone else had this issue or knows why I got it? Just don't want it to happen again
Upgrade your phone's firmware. That way you are certain that most bugs are taken care of.
Hello there guys. This is my first post on this forum, so please bear with me. I have problem on my device. Basically my htc hd2 was running fine, i had all my programs installed etc. I have created various backups of the phone using sprite backup.
I decided to do a hard reset because the phone never used to go into standby (screen off) when charging, only the backlight used to dim. I checked all the settings and i set the device to dim after 1 min and switch off after 2 mins when connected to external power. It still never switched off, this was turning out to be a nuisence specially when getting missed calls at night and screen staying on.
Therefore i done a hard reset and used sprite backup to restore various backup's as i had a few, but they wernt making the device function correctly. So once the backup file's were restored everything would be fine on the phone untill it went into standby, it then would fail to respond, sometimes the hardware button light up, sometimes nothing. The screen would remain off. I would really like to use the backup files as restoring the phone manually would be teadous. Any clues in what could be causing this, cant be the case off a bad backup as i have created a few.
P.S When hd2 is returned to stock it functions normally. Programs installed battlog, clear temp, bsb tweakes opera 10, opnmarket, skype, spb wireless monitor, coreplayer, srs wowhd 1.5.1.0 v2.1, coreplayer 1.3.6, myplayer, 1NETCFv35.wm.armv4i, 2NETCFv35.Messages.EN.wm, resco explorer + reg editor, cht cookie hometab.
Really appreciate it if you pros can shed any light on this? cheers
do you have s2u2 installed?
if so goto settjng power and switch power of in setting to off.
i had a similar problem, this seemed to cure it
hth
nev
Hi nev, thans for your reply, no i do not have s2u2 installed, also i would like to add that when the device was left overnight on charge, it fails to wake up,the screen stays blank only the hardware buttons light up and shows the orange charging light. Please guys help me out here, thanks
I'm a little stuck for another solution. I'd always thought that this was an issues with sprite and s2u2, seems no now.
Would you be willing to test? worse case you could un-install S2U2 or disable it.
It would be interesting to see if installing S2U2 and disabling the power option would fix the problem.
Which lock screen do you currently use?
All of the problems you are describing are exactly the same issues I was having.
Hi Nev, so you reckon sprite backup software could be the problem? I have never had S2U2 installed.
I have restored the phone to factory it works as it should. Nev are you suggesting that i install S2U2 after restoring the sprite backup file, then disable the power option?
oh i am using the winmo default lockscreen with device password.
How did you manage to fix your device then? Were you having the same issues when restoring using sprite back up files? If so could you please give me a brief rundown on what i should do?
Seems like this is not a common issue on here judging on lack of replies. Thanks for your help nev.
I'd give it a go. You have nothing to lose.
S2U2 is an excellent piece of software, amongst other things, it has password protection, and allows you the option of reviewing txt, mail, reminders, etc all from the lockscreen. Additionally, you can set it to allow quick switching between vibrate and sound profiles. ("sales" pitch over)
If your not going down this route I suspect that another hard reset and re-installing you apps from scratch is in order.... I did this about three times before I realised that there was a conflict when restoring from Sprite.
good luck
explicitsoundz1984 said:
everything would be fine on the phone untill it went into standby, it then would fail to respond, sometimes the hardware button light up, sometimes nothing. The screen would remain off.
Click to expand...
Click to collapse
your symptoms seem kinda similar to "Leo Screen freeze crash Issue"
Thanks guys for your help, i think i am going to leave it stock for a while and see if the screen plays up. I dont fancy doing all the sofware installs, incase the device is faulty. Thank you that link p107r0
good luck with yours, btw I used to have the described 'syndrom', hard reset helped, since than I keep most of the old backup copies, assuming that if anything similar happens some of those should work properly
Same problem here - SOLVED
Guys,
I very recently faced the same problem that it was virtually impossible to wake up my HD2 from standby after I had to do a restore with Sprite Backup (same problem as reported by explicitsoundz1984).
Since I actually found two solutions to fix the problem permanently, I like to share them with you:
Solution 1) After I removed all non-stock program links from the autostart folder, the problem was still exisiting. Therefore, I checked the list of installed apps from explicitsoundz1984 with mime and found a potential suspect: "srs wowhd" which obviously is buried deeper in the OS. After de-installing "srs wowhd", the standby of death problem was permanently gone!
Solution 2) I read in another threat that the standard restore options of Sprite Backup do not replace the current registry with the backup registry, but tries to "merge" them - this obiously leads to the situation that a full restore from a stable backup set can result in an unstable configuration.
After changing the restore setting for "system settings" to "replace" instead of "merge", the resulting restore was again a stable one.
Cheers,
Jan
Yes
with Sprite you must use erase and restore. You have to reset these parameters each time you are going to do a restore. It merges by default. If you are going to restore directly from the backup file on the SD then just double click on the file and restore. Then go into Sprite and change the parameters to restore and erase and restore again. The first one directly from the file execute will merge A pain but it works.