anyone know how/where to get an xda mini II repaired? i'm in italy, but i can careless where it has to go. I'm at the point where i would rather just sell the device for it's workable parts (if there are any)...Today the screen has done a myraid of interesting things...anywhere from blank to thousands of vertical lines....ugh...
ohh yeah...warranty is void....or is time to just move on?
ok...no answers so i thought i would add some images ...anyone seen this before?
Mate i had a similar **** up a while back ...I did a HR and it worked fine..for me it was caused by a Overclocking software [Dnt want to Name it ]
If this dnt work try the Batt out and back in trick
Call ur Local service Center...
mine looks exactly teh same! but it happened after i tried to replace my housing, i screwed up the little gold prongs where the ribbon connector from the lcd plugs in...****! any ideas on how to fix? im the us so service center isnt really an option, and id ont want to send it off.
hi i had the same problem with my magicians, after i changed the housing. i found the problem with my device was that i had not plugged the screen back in properly. all i did was to ensure that it was pushed in properly before i clipped it back in
Menappi -
I had the exact same issue. I reopened the casing WITHOUT disconnecting any cables. I flipped the screen's ribbon black lock up, while maintaining pressure on the ribbon so that it does not pop out. When the black lock lifted, the preasure of my finger moved the ribbon further in . I pushed the black lock down, reassembled the device and ... PRESTO!! the screen works perfectly... and chumps on the bard advised to buy a new screen!!
Good luck
Hi All,
seems, you have problem somewhere in display connector. However, sometimes I see similar picture on physically broken displays, let's imagine, you were careful ad didn't use a hammer during housing replacement.
There are two possibilities: at first - try to remove and re-insert display cable (I hope, you know. how brown lock works). If there is no success - try again. At second - some wire on flat cable may be damaged. Sometimes, good technician with soldering iron can fix it, sometimes not. And if you used force, removing cable, board connector may be damaged too. However, only the experienced man can find it easily.
So, try to carefuly re-insert display cable. Try several times. If you are unsuccessful, you, for sure, need an experienced technician to fix your device.
I hope, you are not enough mad to send device for repair to Russia
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
"obviously very sensitive soldering will be needed"
And that only can be done by machines/robots. I don't think humans are even able to sloder those kind of connections...
But, could you post a picture? cause I might have suggestions on how to fix it. One would be to bend back the pins on the tiny slot with a toothpick and when done to tape the flatcable, so it stays there.
I've maybe got a spare creen for you.
g0atNZ said:
So I bought a new housing for my O2 XDA II Mini, during the removal of the display ribbon I broke the little black part on the display connector which holds the ribbon down, and after hours of trying to get the ribbon back in and secured I have bent the pins in the connector to buggery.
The ribbon appears to be untouched, however the connector which the display ribbon goes into is broken.
Is there anywhere I can get hold of one of these little connectors to replace my broken one, obviously very sensitive soldering will be needed to remove the old one and solder the new one in place.
Alternatively, does anyone know any mobile phone repair shops in Auckland, New Zealand who would be able to help out with my situation?
I fear all i'm going to hear back is "the motherboard needs to be replaced", however I am determined not to go through this route, as I am a poor student and the phone sounds as if it functions fine, makes the beepy noise when first starting up on the setup screen.
I was very careful with the actual screen unit while removing it, and I have had signs of life earlier on in the broken connector episode, however I can no longer get anything showing as I can't fit the cable in.
Cheers for any help.
Anything would be appreciated.
Click to expand...
Click to collapse
Hi, I've still got a SPV 500 and a MDA Compact, need to find it if you want you can have my MDA Compact screen.
Just PM if you are interested.
Hi, I come on here quite a lot for information as it's an amazing resource! This time however, I'm attempting to give something back!
I experienced the "black screen on slide out" on Monday. Phone completely screwed. I've also had a few droppages and had it apart once before so there's no way warranty is gonna help!
I stripped it down and soon discovered what it is that actually fails on the ribbon. The coating had worn through due to rubbing on something during the slide out / in process. it had been playing up for a while, probably due to shorting out on the metal case, but now the tracks (aluminium?) had worn right down.....
In pic 1 i've circled the worn area. The shiny section is where i'd tried taping over it to prevent shorting, before i realised the tracks were gone.
Got an almost new one off ebay for 15 quid and, realising it was going to happen again, came up with a solution that, so far, looks like it will work....
A while back I bought some "anti rattle felt" for my car's dashboard - really thin and strong self adhesive felt to prevent squeaking joins between dash sections. I cut a piece of this and stuck it to the new ribbon. Once this stuff is on it's well stuck, by the way!
See pic 2 for the modded ribbon cable.
On reassembly everything is working just fine so far! Here's hoping that it lasts longer than 6 months this time!
Just need a new casing now as mine is decidedly second hand!
Hope this turns out to be of use to someone!
cool story bro
when i took apart my xperia to replace the housing this seemed like a really weak point in the device. glad to see someone who has had the problem has been able to fix it
Why does the screen go black?
Hi,
When the coating wears off the ribbon cable it exposes the tracks in it. when you slide the keyboard out the exposed tracks short out on the metal casing and the screen loses it's input signal.
thats whats happened on mine at least and i presume quite a few others?
HTH!
Update:
That's interesting: My phone was also losing signal with the keyboard out, and occasionally while closed up as well. It would just randomly drop to "no signal" for a few seconds.
It hasn't done it since replacing the ribbon cable.....could be coincidental of course.
I'm having the same problem
It just started a week ago and I got the phone in January off of ebay. I'm new to opening up the phone so could anyone help me find the correct tools or have a link to a site with pictured instructions?
I noticed that the sliding mechanism started to go loose about 4-5 months ago but didn't expect the screen not respond in landscape mode. I have yet to see the other symptoms you all are referring to. I would like to fix this before it get worse.
In mine case it went totaly black after one week of this problem... You have all the instruction on youtube, there is where i looked. For tools you can be inovative, but the exactly right ones come with housings from ebay, it is only 15EUR, and i bet you have some cracks so it wouldn't hurt replacing. That is what i did, along with ordering new sliding mechanizm, and new ribbon cable.
I am open for ideas to prevent my ribbon cable from being cut at it weakest point again.
I'm assuming my flex ribbon went bad yesterday, since sliding the keypad out causes my screen to shut off.
Already ordered a cable off ebay and will attempt to replace it myself :O
Replaced my flex ribbon cable with one I bought on eBay. The screen doesn't turn on at all now, which leads me to believe the cable I was sent is defective. Put the old one back in and it works okay, less landscape mode. ughhh what a pain.
great tips! my input is I bought a case off of ebay that was ~60$ and everything actually fit fine for me...so I wouldn't discount every seller but you do get what you pay for, the 15$ cases are probablly the ones that will give you problems
I working in a mobilephone repair center if anyone need help drop me a priv... i able to get 2nd hand or even brand new components
Replaced the flex ribbon cable -
I got my flex ribbon cable a few weeks ago and took it to my local repair shop. They replaced it but the LCD screen/optical joystick receives no power. The touchscreen and everything else on the phone works just fine now. I thought it was a defective item so it was exchanged with a new one.
Got the repair shop to replace it again and the outcome still remains the same as the first.
Theres no light coming from the screen nor the side illumination.
I just told the repair shop to just place the original back in for the mean time.
Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power botton.
Could it be defective a batch that the seller was sending out? or the repair shop's mistake and is playing dumb so they do not have to admint fault?
Hopefully there's an easy fix to this problem.
-Also I did inspect the ribbon before and after the repair. looks new as the OEm
Can anybody help me out with this new problem after replacing the cable -
perhaps you should try a hard reset. Ive had problems in the past where the optical joystick and the illuminators did not work, and that worked for me.
On the other hand, the top illuminators are on the same piece of hardware as the flex cable that was replaced, so a faulty flex cable is possible. The bottom illuminators are on the circuit board that the optical joystick attaches to, separate but connected to the flex cable.
Ive recently replaced my flex cable and touchscreen. The experience i had with the faulty touch screen was that it appeared to receive no power, but was in fact displaying a dark backlit illumination that could only be seen in the dark. At the same time however, the screen did not display anything. I'm not sure if this is similar to your experience, but if so then your touchscreen would need to be replaced.
ive done all repairs on the xperia myself, and one thing ive discovered is if something doesnt work right after a repair, simply disassembling it and reassembling it to make sure all the connections are properly done has worked for me in the past.
"Before the repairs, there would be a flicker of white light and random illuminations. Now there's no lights at all except the power button."
Now when you say the power button, do you mean that a red light appears under it?
I dont know if i can come to a conclusion or that i can help (or have helped) you come to a conclusion, but i can only assure you that the xperia acts out in strange and weird ways.
Good Luck!
Tags
Dismantle / Disassemble Sony Ericson Xperia X1
http://www.ifixit.com/Teardown/Sony-Ericsson-XPERIA-X1/788/1
http://www.formymobile.co.uk/xperiadisassembly.php
http://www.youtube.com/watch?v=AWDurQrRt-Y (REAR)
http://www.youtube.com/watch?v=iyGUbxFqvyc&feature=related (FRONT)
http://www.youtube.com/watch?v=elgC8hwHfYQ&feature=related
For info.
Mike
Thanks for the links. I've tried the hardreset and restoring the original rom but the issue is still there. It's really bugging me that everything works but the LCD screen. I'm currently using MyMobiler to use my phone. The touch screen works fine and so does the soft keys. Just no power for the lights. I might just give up and wait for another phone that catches my eye and then tinker with the xperia myself. but if anyone got a solution or want me to test something then I'll give it a try.
My warranty is no longer affective so I'll use my phone as a tester to help others with any problems.
TRIONDAVE, how's your Xperia running now with the cable mod that you did? Its been 6 months since you created the thread. I hope you're still around.
My Xperia X1 works nearly fine, except for the keyboard issues, so I'm thinking of opening it up. If your Ribbon mod helped I might just do it too once I've got it opened. Mine has a MOUNTain of cracks though, and the battery compartment itself is cracked on both side enough to make the compartment CURVED. Hence the Battery cover doesn't sit well.
I'm looking around for broken Xperias which I might be able to use to change the internal cracked casing. Lets see.
DatDereX1 said:
cool story bro
Click to expand...
Click to collapse
My thoughts exactly.
Hello guys, I am in need of real help over here!
Its just that Ive replaced my ribbon cable, the old one got screwd up.
However I got done for 10 minutes ago, tried to start up the phone.. without success :,(
The ribbon cable doesnt have anything to do with the start up, only the screen am I correct? Cause I cannot even start my phone..
Ive connected the charger, but when I remove the battery it shows a red light, meaning no battery, correct?
So what may the problem be exactly? Maybe the battery is all dead, or?
PLEASE HELP!
for the people with ribbon failures how long have you had the phone before it occurred ? im just interested on the cables lifespan.
mine is fine so far but i have noticed the slider is flimsy and rocks left and right.
So my g/f droped my phone and my touch screen completly stoped working. So I went on a limb and replaced the digitizer and I thought all was well. Unforunatley only parts of the screen if you were to break the screen into 1/4s the top quarter doesnt work nor does the third down. So im thinking either the digitizer i recieved is defective or the ribon cable on the phone side is damaged. I have tried to reconnect everything all seems well.I have also tried a hard reset to no avail Any ideas guys could use some help!
Does anyone have a breakdown of the phone with part numbers and names. Im going to try and get the ribbon cable that connects the digitizer to the phone the one that runs under the power button.
xxiamdrewxx said:
Does anyone have a breakdown of the phone with part numbers and names. Im going to try and get the ribbon cable that connects the digitizer to the phone the one that runs under the power button.
Click to expand...
Click to collapse
Unless you really know what you're doing, this will be impossible. The screen and that ribbon are connected. Best bet is to just replace the entire digitizer again. Or do like I did, warranty it out. My screen shattered, door met phone, and I replaced it but had a dead spot, so I just called att and had them replace under warranty.
never mind found it the ribbon cable is one big piece for all connections! 15 bucks.
Hey,
i got the typical problem that my screen wasnt responding after use of endbutton. Sometimes it was working.
I now disassembled the device and saw that the flatcable had a small scratch and i guess the first one or two cables are brocken already and only get contact sometimes by luck.
So does anybody know if there is a way to repair this ?
A new touchscreen isnt to expensive 20-30€ but why throw away a working one if a cable is repairable easily?
Next time i will glue the cable to the display so that there is no flexing when pressing the endbutton. The problem is that there is a little space between that is pushed away each use of the endbutton and someday the problem occours.
Hi,
I had to replace my touch screen to solve the same issue
Is there any thing we can do to prevent the same damage to the new screen ?
Thanks
Well i tried a few times to fix the issue.
But its hard to solder the flex cable without totally burning it.
If i solder it its very likely to break fast again.
Im going to buy a new digitizer too..
To your question:
Yeah i saw that there space between the flex cable and display. The cable is bent a bit towards the buttons. When you push the button the cable is bent back in the free space.
I will glue the flex cable directly to the display and put a layer of protective tape over it. so it wont bent (What causes our error) and wont scratch(if this could happen too).
The problem is the poor quality of the flex cable. Its very hard and therefore breaks easily what causes the wires to break to sooner or later.
If i can ill try to take a few photos but its hard as my digicam cant focus so closely..