Related
Guys, I hope you can help me!
I was using my Imate Jasjar when it was accidentally bumped by another person. the Jasjar fell but it wasn't that high and the floor was carpetted. However, I noticed that whenever i try to tap on the Start button on landscape mode, the calendar application opens up! And when I try to tap V-Bar on the other corner opposite the Start button, the Contacts application opens up. Basically, the soft keys on the bottom screen are the one opening up even if I'm tapping the ones on top! If I tap the bottom soft keys, I thought the Start button or my V-bar would come out but still the Calendar and Contacts applications were the ones that opened. Basically the everything on top cannot be tapped!
On Portrait mode, I can tap the start button but when the V-Bar was tapped it still opens the Contacts application.
I went to Settings then Screen to re-align the screen. I thought it would solve the problem but apparently it didn't! I was trapped in the Align Screen section giving me an endless loop to tap the 5 areas of the screen.
I now did a Hard Reset, and now I'm forever got stucked to the Align Screen part.
What am I supposed to do??? Please help!!!
Hi,
Seen the same problem... Try to guess the error margin of the alignment...
for example instead of tapping in the center of the cross try tapping on left or right... Since your screen isn't aligned you can't press on the center...
Now the problem is hardware, not the MB but the LCD...
After tou figure out the margin error, the Universal will resume and then you ca align the screen via Start->Settings->System, align screen
I'll try to know more about this problem asking my friend.
Best of luck
thanks for your reply!
i also believe that it has something to do with the LCD. there are no cracks whatsoever. problem with the aligning is i have to keep on guessing. and if ever i do align the screen successfully, i'm not sure if re-aligning the screen in Settings would solve the problem.
i would appreciate though if your friend or anybody else can shed light to a solution.
This is a simple problem to solve ;-)
When the allign screen is ON and you have to make the first tap on the crosshair (just before you start clicking away to allign your screen), twist your display from landscape to portrait mode...
Now continue to allign it as usual, and you should finish successfully!
Cheers,
San
unfortunately, after following your instructions, i still went on an endless loop on aligning the screen. i'll try to reflash the rom and see if it would work. i hope it does...
i updated my ROM. still stuck on the alignment screen!
any more ideas?
To be honest, sounds like your screen is broke. Even if you got it to align, I doubt it would be very usable. I think you are looking at repair - if there's no visible sign of damage, you might get away with a warranty repair.
Cheers,
Steve.
Hi
Few months back i've got exactly the same problems (odd LCD behavior, impossible alignment, etc...) with an HP4700. I went to the service center and they had to replace the LCD screen. They did not charge me and take it under warranty. In my case the unit did not drop and i made it clear to them. I would suggest you go back to the service center and forget about the drop in your problem description .
Cheers,
Bruno
I had the same thing happen on a HP 3700, I did not even drop it all i did was install the Quake game for it and after a few days the screen alignment went a bit out. It was usable but definately out by about 1 cm in each direction. The unit had not been dropped. I went into the allign screen utillity and ended up in the infinite loop. The only way to fix was a new screen. But unforunately it was no longer under warranty. The screen consists of 2 separate parts the lcd and the touch screen bit. In my case the lcd had no issues just the touch screen. Very annoying but there you go.
Search your soul and do what you feel comfortable with.
Good luck
Charlie
thanks for all your replies!
i've made several searches yesterday with similar problems (even if they're using different PPC models) and they all ended up sending back their units for repair. there's even one who posted in expansys with the same exact problem!
we'll be sending it back through expansys (we got the unit from them) and hopefully get it back before the end of the month. and yes, i won't tell them that it was dropped, he he :twisted: and they won't find evidence either on the outside because there are no physical damages. what a start of the new year for me <sigh>
right now i'm back using my XDA IIi.
thanks for all your support! this is my first thread/topic in this site and it's so unfortunate that it had to be sort of a negative one. looking forward to be active more here!
Hello there
This might help (I am currently wrking with 200 PDAs so have had this a few times)
THere may be a iece of dust/biscuit crumb etc, under the edge of the casing above the screen, try using a post it note or paper and go around the casing/edge of screen, this should clear the screen of anything that may be causing this problem.
THis worked for me on the majority of non-aligning screens
HTH
DB
My story was, one day when I needed to twist the screen, it was a bit stuck so I twisted a bit harder, yes it went back. Then few days later, the mis-alignment started and since then I have been keeping to do re-alignment my screen.
My screen is mis-aligned once every 2 or 3 days or even few minutes then I have to re-align by using WM5's alignment program. It sometimes takes me 2 or 3 times or even one time.
The most anoying thing is it keeps forget after aligned screen.
Now, certainty, I don't think it is a screen problem because after running alignment app, it correctly pointed into the right spot but then it forgot where the right position was.
I have done the upgraded ROM ( even tried Ivan AKU 3.2 ROM ) but problem still persisted.
I just tried clean up the edge of screen, finger cross, hope it fixes my problem.
Bad thing is, I bought my device from UK and I am living in Australia so therefore, my warranty is definately invalid. I don't want to spend 200 AUD for the new screen ( unless I am 100% sure that LCD is faulty ).
Anyone has any idea or even a better suggestion because I don't see many people having this problem.
I suspects that maybe the flex cable got ripped but not totally ripped. Don't know , please help me out on this one
Best regards
Anyone has any idea about my problem ??
One question :
I know that the flex cable has 2 connectors ( one is for LCD display and another is for LCD function ). Now does LCD function relate to the touch screen function ? and if one tiny wire of the function cable got cracked, but not totally cracked, will it affect the touch screen function ?
Other thing, does WM5 store any setting relating to screen alignment setting ? If yes, where is it ?
Thanks
Hi, from another forum, it only help to bypass the alignement loop:
"here you go theses are simple steps to bypass the touchscreen alignment.
Install you activesyn blah blah blah when it finds it go on my computer and go into your PDA device
go to windows startup and delete the Welcome file
after that give your PPC a soft reset and BAM u by passed the screen now get a free desktop program liek pocket controller from the internet it will automatically install on your pda and BAM you can control your pda add music and whatever
but now if you want to click stuff on the road get pen irazu just search on google and send it to your PDA then go to file explorer and double click it and you got a cute little mouse program that you can use like a stylus"
also try this little soft:
http://www.codefactory.es/downloads/mobile_speak_pocket/release/MSP_RemoteAlignment.zip
Hope it helps.
MaX
Hi godtakeit!
I've had the same problem a few weeks ago (and still having it from time to time) and for me a slight (very careful) bending of the screen makes it work again. It seems to me that there are connector behind or near the display which has some loose contacts.
Did you notice any other problems which came in conjuction with the alignment problem (e.g. speaker not working)?
.ox
Hi oxident
No, I don't have problem with speaker ( it was not working before but it is because of the jack plug problem - it solved ). Yeah, I did notice if I bend the screen carefully, the problem is gone. The funny thing is when I aligned the screen, it worked but if I closed it off and left it over night, it started again when I opened the lid.
You may right about the connector between LCD screen and mainboard. Well, I have no choice but openning the device and check it up.
Also, I read the thread somewhere in this forum and somebody advised this problem maybe relates to magnet around device. My brother aslo advised me that LCD charged and reserved negative electrons. Wierd but I am experiment it at the moment ( taking off battery and leave the device for a few days so that it can release the negative electrons ).
Hope it fixes
please help
i have an imate jas jam that i i got from my father he used it for like 3 years and it is pretty banged up so i cant use the warranty and repairs cost a lot, any who i got it yesterday and it was very slow so i reset the settings and now im stuck on the align screen it keeps going on for ever and ever if any one knows any thing plzzzz help
Welcome aboard
You have one of the best HTC devices ever made!
Have a look here to locate the solution to your prob:
http://forum.xda-developers.com/showthread.php?t=549207
Post number 2
Good luck,
Guys,
My partner just closed my phone in her car boot. It works fine which is good however, half the screen is cracked and dead not good. Will it be chaeper to find a replacement screen, by another Trinity or move to something new.
Where could I by a new screen?
I appricated your comments.
Rich
think i have answered my own question...
http://cnn.cn/shop/p3600dopod-d810-screen-p-1734.html?osCsid=d538dc0645483ca7551cfc78c4c9fab2
anyone now anywhere in the uk?
do I need special tools to fit this?
Hello just for information,
I broke my trinity screen and I baught a new screen to a HK seller and i replace it.
I had already flash the firmware (faman 3.6 full) before changing the screen.
So everything seems ok when I put the phone power on but As soon as I put the creen off, I am unable to put it on it appears every time in a complete white screen !!!! to have something on the screen I have to reboot the phone.
I just reflash the phone again with faman 3.6 and it's still the thame problem completly white after turn the screen off then on ...
I try also an official orange WM5 (gps active) and the screen work's well i try after to switch again in WM6 and it doest work :white screen again ...
Can every one help me ?
@ Rich: Check the 'How to dissamble the Trinity' thread. Are your sure that the LCD is broken ? Could also be just the digitizer (USD 8 at cnn.cn.shop).
If you succeed to dissamble the display you should be able to attach a new digitizer.
The only problem are the two black levers ... (one for the display cable, one for the digitizer).
Good luck
Christian
I cracked my Trinity screen with a bad golf swing. Then I bought a replacement screen on ebay, found a disasembly guide, took my trinity apart, replaced the screen, put everything back together, and it works fine! cost me 70 EUR to fix it.
do it following the disassembly guide - taking the trinity apart is rather complicated, you will not figure it out by yourself.
Sometimes I wonder what the engineers drink before designing such complex assemblies!
I need a replacement windows PDA phone for my lost wizard... and i have a friend willing to sell his 8525 for $50... the downside...
according to his is... his touch screen works half the time.... something about working on a full charge... or not working on a full charge... and when its halfway charged... it does the opposite... etc etc...
he said the screen lights up just does not respond to the touches under the above mentioned conditions.
i did a search over here and HOFO.... and have noticed alot of people have problems with the top right corner of the screen (portrait) being stuck and closing out apps.... or launching the start menu repetedly...
and there isnt really a fix?....
is 50$ still a good deal?.... will a replacement screen and digitizer fix it?.... which is around another $50 i believe?
or should i buy one from ebay... they are selling for around 170-200$ shipped.... or is this a problem that plagues all 8525 hermes eventually?.. and i shouldnt bother with this model... and go back to the wizard or get something else?
The Hermes is a really great phone (I passed on getting a Kaiser, as it didn't offer enough of an upgrade), but I don't know if I would personally buy one in that's having issues like that.
50 bucks isn't bad, though. I might bite for that price.
I've had no screen issues over the last 1 1/2 years. I just saw a used 8525 sell for $181 on ebay...it's a great scalable device!
Alright.. i got a hold of the phone.....
everything seems great.... touchscreen was working... but as soon as i went to charge the battery.... and took it off charge once it was filled up to 80%, the touch screen stopped responding...
and i also did a hard reset ... and the screen still isnt responding.... and i cant pass green setup screen that asks me to tap the screen to continue.
any way to bypass this screen?... i dont mind using the phone with only the buttons...
and do you think this is battery related?.... the prev. owner said something about... leaving the battery to cool over night... and pop it back in... and touchscreen should respond again....
any suggestions?... thank you.
Find the program "Remote Screen Alignment". If you can get the Hermes to screen alignment to work, you can save the settings to your pc then if you reflash an os or have to hard reset you don't need the touchscreen. Try taking the battery out overnight and see if you can do the alignment then. Once past the screen alignment you can operate the Hermes using the buttons BUT you need to first get past the alignment settings.
Alternatively, if you know someone with the same Hermes you can get the Alignment settings off their phone. You need the above app.
Cheers...
if your looking for a screen, i have a screen complete with digitiser for sale? PERFECTLY working
i can also throw in a ribbon cable which works but only displays colours in 4bit mode!
PM me if you want the screen
ultramag69 said:
Find the program "Remote Screen Alignment". If you can get the Hermes to screen alignment to work, you can save the settings to your pc then if you reflash an os or have to hard reset you don't need the touchscreen. Try taking the battery out overnight and see if you can do the alignment then. Once past the screen alignment you can operate the Hermes using the buttons BUT you need to first get past the alignment settings.
Alternatively, if you know someone with the same Hermes you can get the Alignment settings off their phone. You need the above app.
Cheers...
Click to expand...
Click to collapse
well its not even the screen alignment screen that im stuck at....
when you do a hardboot.... the FIRST splash screen that shows up after the ATT stuff
its a green screen that says windows mobile DIRECT PUSH... and it says
"please tap the screen to continue etc etc"
will that program help me get past that?....
and the battery is out of the case right now... and im in school..., hopefully by the time i get back home it should work.
duke_stix said:
if your looking for a screen, i have a screen complete with digitiser for sale? PERFECTLY working
i can also throw in a ribbon cable which works but only displays colours in 4bit mode!
PM me if you want the screen
Click to expand...
Click to collapse
well... i see that you live in the UK... it might not be favorable purchasing it from you...
and tihs ribbon cable that you speak of.... do i need one for the isntalation of the screen?... and the one you have isnt made for this phone right?
Alright guys... so pretty much what the previous owner says checks out..
the phones touchscreen started responding to touches on a cold battery that was sitting for a few hours....
as soon as i begin to charge and the batter warms up... or the phone warms up.. im not sure... the touchpad stops responding.
ANY SUGGESTIONS?...
is this an issue with the battery or the touchscreen?...
aside from that.... this phone is fantastic!
Hi there
I am in the UK, and the screen has in fact been removed from a cingular 8525 i cannabilised for the d-pad board, the screen works perfectly and the ribbon cable will of course fit your phone.
I am willing to ship to the USA, and in fact i regularly do, only recently i just sold a little rubber dust cap for the hermes on these forums and its on his way to him right now. if you can pay via paypal your more than welcome!
Not the battery. The battery only supplies power to the mainboard and through that to the lcd. If the battery was at fault then you wouldn't be able to start up. It sounds like you may have heat problems with either the lcd ribbon or with with the flex ribbon connecting the top part of your phone to the mainboard. If I was you I'd check out Mike Channon's site as he is the MASTER of Hermes hardware and if you don't find a solution you can PM him. Heres a link to his site - http://michael-channon.spaces.live.com/
Cheers...
id buy it and sell the parts on ebay
OK I have had my T-mobile Wing aka HTC Herald since last April.
Just a few days ago I encountered a problem with my lcd. And I would like your guys feedback if possible before I purchase an lcd replacement.
My problem is when I slide open the wing my screen starts to fade, (almost making it look like a negative from a picture) after that it starts to fade to different colors.
Now the problem persists when the phone is closed, however if I tap the top of my wing and hold it the screen becomes normal, but once I let go it starts to fade again.
I would like to know if any of you experienced this with ur phone and if a replacement lcd screen will fix the problem or am I sol?
If it helps im running my wing on Open Touch v6.0 WM 6.1 Build 20273.1.3.3
Thanks in advance.
LCD problems
Hello,
I too have some weird LCD problems and instead of creating a new thread I thought of posting in this one.
For the past few months, whenever I get a call or resume my phone from standby mode using the power button the entire screen goes white or sometimes it has green or blue colored lines all over them. I have to keep on pressing the power button few times to get proper display. Also whenever I open the qwerty keyboard the display goes blank. Since I am out of warranty Tmobile is not ready to replace the phone and I contacted the HTC customer service and they told that the display unit and some hardware stuff is gone and it needs to be replaced and will cost a minimum of 170$ and will increase if they had to replace some other hardware.
Please note that, my screen is NOT broken and the touch screen too works fine. Recently the display has gone completely blank or too faded even to see whats there in the screen I could barely see the today screen.
I searched and I did not find any similar issues that other folks have faced. Since the LCD and the touch screen is not broken replacing them is not going to fix the issue, correct? I was using open touch and recently I updated the latest official Tmobile release of ROM 6.26.xxx. I also tried the hard resets too.
Any other ideas/suggestions will be of great help for me. Thanks in advance.
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
handsome22 said:
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
Click to expand...
Click to collapse
link to the thread containing some info about the software... its called my mobiler
thanks for the info
touchscreen was working today morning, took battery out for 2 hours, turned it back on and it was working abit weird, and now i cant press any touchscreen buttons atall!
So no softkeys (pick call, home etc.) and nothining on the big screen! I can turn on the phone, press the power button and volume buttons, see my home screen get calls etc.. hard reset twice, took battery out, nothing does it .. gonna try flash it but dont think itll do it ... and ideas?
Im in uk aswell if that makes a diff
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
I had the same thing, a oily spot, but it was there for months, then i noticed another new spot (looked like a tiny tiny burn) and thats when it stopped working completely... ive ordered a new screen which should be comming in a few days, im hoping thats the issue
will let you know if it works ....
keep me updated if you find anything
thanks!
NECROSTONE said:
I had this happen to me yesterday. I was surfing on my phone as per the norm. Put my phone down. Got a txt, picked it up and it wouldnt allow me to access it. I thought it must be a freeze as it has happened occasionally.
So I restarted.............and nothing. No response AT ALL from the touch screen.
I have noticed the oily spot problem on the most part of my screen, and thescreen doesnt have that little give it used to when using it (paranoia possibly)
So I can only assume something has given within the screen. Ive been searching all day on the internet for causes and fixes but nothing has come up.
The volume and power buttons work but I cant do anything at all with the phone as its obviously all touch based.
Is this a screen replacement job then or is the whole phone goosed?
Roheelshah if you turn your phone off do you have the massive oily screen thing?
Any help is most appreciated....
Click to expand...
Click to collapse
download and install this _HTC Touch HD_TouchHD system.exe
BOLDESH said:
download and install this _HTC Touch HD_TouchHD system.exe
Click to expand...
Click to collapse
whats it do? and where from??
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
ok basically i received a new digitizer today (the actual touchscreen) ...
i dismantled the whole phone using the service manual and some video some guy made (VERY HELPFUL, if anyone wants it for any reason i can post a link), ok so i got rid of all the top bits, the circuit boards (or watever theyre called)
I got down to just the bezel, lcd and digitizer (dont know what a bezel is, the lcd is where the display actually is and digitizer is directly stuck ontop of that)
Apparently when replacing the screen, htc have made it so that you have to replace all three of those parts instead of individual ones, but you can buy them seperately so i thought i'd hero it.
i poked out the screen from the frame (some chewingum like stuff holding it in) then i started peeling off the digitizer (if you get one and want to try it you'll know where to peel) ... this was a mistake tho cause the lcd is unbelievebly sensitive so while peeling off it left scratches on the lcd, and me not knowing the lcd is sticky tried to wipe them and use a dust free cloth, which left alot of crap on the actual lcd!
i managed to get the digitizer off and ripped the cable that goes from digitizer to whatever reads our fingers on the screen, took it all off, placed the new one directly ontop and fed the wire exactly how it was for the first screen.
Put it all together again
Now I did mess up my screen badly, but in a good way! .. i now have full touchscreen working (smoother than ever) but my LCD display is near enough gone, so it looks like the screens really really dark, and i have to tilt it at certain angles to see the screen..
After all of this i now have a touch hd i can controll from my pc (using mymobiler) so i can recieve calls, send texts all from my pc when connected thru active sync, can even play teeter ... but not really the same!
I wouldnt recomend anyone to try what i did, although i think its worth the risk as I would have to replace the lcd anyways if i wanted a new screen in the first place... and who knows you might be able to peel the digitizer off clean (NEVER EVER EVER TOUCH LCD WITH ANYTHING!!!).
It all cost me around 10-15£ for the digitizer and screwdrivers and alot of hours dismantling phone compared to 50-100£ for a new lcd.
I am either going to get a new lcd now so i can actually see the screen, or get a new phone.
Sorry for the essay but hopefully this helps someone in any similar situation
if i do get a new lcd will post how it goes and if it sorts out everything
if anyone knows of any other reasons why my lcd would be so dim (brightness is 100%) accept for me getting carried away with it ... help would be appreciated
the_cool said:
I just posted something like this a few days ago, pulled my phone out and screen wouldnt respond, had these marks all over my screen, "swirly marks" as i describe it, very well could be the oily marks you are talking about. you can move them around with your finger right?
anyway, i took my sim out, tryna find a spare phone, couple hours later the marks were gone and screen started working again, touch wood its been fine since.
no idea what happened, but try letting it air out or something
Click to expand...
Click to collapse
Yeah swirly oil marks is how myne started ... i think i finished off the screen by trying to press hard on the mark to try and clear it .. . so be careful with it.. but think that overall the screen had seen better days (course only a few weeks after warrenty finishes) ... all conections inside were ok aswell
doczyus said:
Dear All,
I have similar problem. Usuallí I use on my HD NRG ROM. About 3 weeks ago I updated to the latest NRG WM 6.5 23xxx ROM with Sense 2.5 Maxmanila version, and since this upgrade the touch screen position moving randomized up or down from 2 mm to 30mm!!! After this ROM I tryed updating each newer version, but not changed nothing. I need realign the screen about 10 times / day!!! The phone I never dropped or cracked.
Can help me somebody what happened with my HD?
Click to expand...
Click to collapse
Same here. Touch screen not working. Phone never flashed, droped,...
Any solution?
unfortunately, a friend of mine changed the touchscreen without success. Phone was in perfect state, no drop, no flash. Just the touch not responding. I'm not sure that changing whole part lcd+digitizer solve the problem.
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
igothtc2 said:
Hi all!
I've got similar problem with my touch HD. It's stock since I bought it. My touch sense was acting weird, like it wasn't properly calibrated. Like, when I press 7 on phone pad, the phone actually presses 1, and if I press 0, phone presses 5 and so on..
I've tried to align the screen, but it doesn't get aligned the first time. I have to repeat the process about 4 times before it gets aligned. That's good for about few minutes and the problem is back. Hard reset was also done, 2 times.
Could this be a fixed with a software update? Does this mean that digitizer will soon be dead?
Thank you for your help
Regards
Click to expand...
Click to collapse
use ScreenCal to fix it, hopefully it can help you
Hakim Rahman said:
use ScreenCal to fix it, hopefully it can help you
Click to expand...
Click to collapse
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
igothtc2 said:
Hi!
I've successfuly installed the cab file on my phone's sd card, but the problem is still there. I don't know where the installed files are, do I have to run this application?
Thank you for your help!
Regards
Click to expand...
Click to collapse
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Hakim Rahman said:
have you hard reset the device after installing the cab file ?? if not do it and see if there are changes...
Click to expand...
Click to collapse
Just did the hard reset. When it asked me to align the screen, I just couldn't align the top left corner. I had to press it like 50 times before cross went to the lower corner. Otherwise, after the align it's good for about couple of seconds and then it's just pressing all over.
I thought I had just some software issues because the screen wasn't dead, it responded to my touch. So, I'll probably have to buy a new screen and digitizer, right? Or do you have any other ideas?
Thank you again for your help!
Regards
firstly screencal installs calibration settings not for blackstone so do not install it, no point. (btw it also increases device touch sensitivity)
secondly you guys should try and install the calibration settings for blackstone, basicly what the align screen does, not sure where to find them for download but i could post the registrys if someone wants to make a .cab from them. (atm i cba making the .cab but i am able to do it )
if the calibration settings do not work i think it is best to buy a new lcd package (or buy new device and give me old one for spares oj)
Rn
hi buddy ! What you mean GSensorCalibrator ??
i didnt mention anything about gsensor calibration dude.
tried and tested screencal the other week and it screwed my blackstone.
install these instead:
*screen calibration, sets the blackstone touch points: (aligning the screen)
if you install a cab with these registrys it should fix the alignment problem.
(if it doesnt then its hardware issue = lcd etc)
[HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP\TOUCH]
"MaxCalError"=dword:8
"CalibrationData"="511,542 183,881 183,198 834,197 833,880"
*this one will maximise the touch sensitivity for those that want it:
[HKEY_LOCAL_MACHINE\Drivers\TouchPanel]
"PressureThreshold"=dword:0
Rn
Does anyone have a recommendation where you can buy a digitizer and lcd from?