How do you setup bluetooth active sync? My laptop is paired with my device, and I try to connect via Bluetooth from my device, but it says I need to make a new connection, when I do make a new connection I get the same message. Any help?
Make sure your COM port # of the serial over bluetooth is 9 or below.
When you pairing your device, be sure the Active Sync Service is included into the service profile.
In the connection setting of your desktop ActiveSync program, include the COM port that is for serial over BT or the Activesync service.
Related
I'm able to sync via Bluetooth. But I have to initiate the connection from my XDA II. Start ActiveSync in XDA II, click "Tools", select "Connect via Bluetooth". Is there a way to initiate the connection from PC ActiveSync?
BT ActiveSync
I don't personally think there is a way to do this unless you take remote control of your pocketpc from the pc. What I have also found is that the Bluetooth is very shaky when anything other than small data transfers are concerned e.g. if you try to surf to a web page with loads of images or you have quite a few pages in AvantGo, the BT connection will be dropped. It is far from ideal...
I have had zero success in synching by bluetooth, all I can do is beam files to the pc via bluetooth, I also cannot browse my xda2 from the bluetooth desktop.
cruisin-thru said:
I have had zero success in synching by bluetooth, all I can do is beam files to the pc via bluetooth, I also cannot browse my xda2 from the bluetooth desktop.
Click to expand...
Click to collapse
You need to create a virtual serial port using the Bluetooth software on your desktop PC. Then set the Connection Settings on ActiveSync to allow connection from the serial port you just created. If your Bluetooth software has an ActiveSync profile, it will do all this for you automatically. Otherwise, you need to use the Serial Port profile.
You can browse your XDA II through ActiveSync. Just select the Explore command.
how to control the assigned com port
the bluetooth software on the desktop insists on setting the com ports as com10 or higher...I read somewhere that activesync does not recognize com port higher than 9.
I re-installed the drivers several times....and it only allows for com 10...and of course activesync does not recognize that as an available port to connect to!!
any thoughts??
setup:
Widcom 1.4.2 bluetooth driver on win XP Pro
Epox USB dongle
Activesync 3.7.1
I am using the same software but it always offers com3 or com4 which works fine, if you right click on the bluetooth desktop serial port profile does it not give you an choice under "properties"? I have worked out how to do most things now but I am struggling with my laptop with bt dongle trying to browse the web through sharing, I know the settings are correct but it just wont let me through, I have a full network access running and can access files etc but no internet on laptop. :?
hi,
I can't use the bluetooth conection to surf Internet in my WinXP SP2 pc.
I have updated usb bluetooth adapter drivers (WIDCOMM) and ActiveSync to 3.8.
I know that SP2 have some problems with bluetooth.
Please, some help?
with ur magician u can only surf internet per Active Sync... the magician has no network bluetooth profile... u can connect per BT to your PC and use AS ?!
Hi ingmar
As you say, i can't' connect then magician via bluettoth with AS. The usb serial port (COM4) is configurated, and this port is set in AS configuration. But AS always interrupt the connection with a error message after a few seconds. With USB AS run ok.
Thanks for your help
Try the following:
On your PC, check the Bluetooth-manager configuration and check which com port number is assigned in your local services tab. Now, go to the ActiveSync connection settings and choose this com port and mark the serial communication check box. That's about it on the PC.
On your PPC, go to Settings->Bluetooth Settings and press the "Start" Button for the ActiveSync over Bluetooth configuration. On the pop up dialog, enable Bluetooth and delete an existing pairment with your PC! After you did this, re-pair the two devices. When finished, start ActiveSync on the PPC and select "Connect via Bluetooth ...". Your ActiveSync connection should be established at this point.
When this is done, you're almost there. If your Desktop PC has a direct connection to the net (via LAN or WLAN), you should already be able to surf the net via Bluetooth. If you connect via DialUP network or similar, you need to configure your Internet Connection Sharing on Windows (only 2000 and XP allow this i think).
Dandie said:
Try the following:
On your PC, check the Bluetooth-manager configuration and check which com port number is assigned in your local services tab. Now, go to the ActiveSync connection settings and choose this com port and mark the serial communication check box. That's about it on the PC.
Click to expand...
Click to collapse
If this com port is unselectable in activesync? what do we do in that case?
I have been toying around with my bluetooth for the better part of a day trying to get it to work. I have installed pocket bluetooth tools 1.0.1 as detailed here http://www.howardforums.com/showthr...9185e&threadid=544932&perpage=15&pagenumber=1 I managed to get the screen with the activesync icon a couple of times during the pairing process. When I went to activesync and selected sync bluetooth I would get a few seconds of connection and then it would automaticaly disconnect without actually syncing anything. I toyed around a bit more and have somehow lost the option to sync via bluetooth in activesync... :shock: I still see the irda option, but bluetooth has vanished. Any idea what I might have done wrong?
@elefas
When the com port assigned by your bluetooth manager is larger than 9, ActiveSync isn't able to use it. In this case, go into your Bluetooth manager and delete existing com ports (both, local and client). Go to your device manager, delete any still existing bluetooth com ports there, check your (physical) serial port and go into its properties. Somewhere there, you can choose which com port it should use. Select one, which is said to be blocked but you actually know it isn't (e.g. Com port 4). Press ok, go back into the same properties sheet and reselect the com port that has originally been selected. Go to your bluetooth manager and press to add a com port (both, local and client). Now you should have a port number less than 10. Microsoft sucks!
You will need a bluetooth connectivity PC wise. I have a standard run of the mill bluetooth dongle with Widcomm drivers. You need to create access for your PDA via network connections in Control Panel. You also need to create an incoming bluetooth serial port in the local services provided by the bluetooth program on your PC. (make a note of Com port as activesync needs to have the same com port assigned when it connects)
I installed Pocket Bluetooth tool on my M1000 running wm5 c. This programs allows extra bluetooth functionality after you have paired with a device. It assigns com ports to each bluetooth device..(up to 9).
Pair with PC. if you have an existing pairing remove it and redo pairing. make sure pairing is initiated by the PDA. Once you have paired it should show the bluetooth services offered by your pc. tick the activesync or serial connection. then it allows you to assign an outgoing port for the pc so as the pda initiates contact. Detailed guides are available on the net regarding creating bluetooth connections and creating shared internet networks.
Trying to BT AS from my JasJar to my PC.
PC has activesync service setup on COM6
AS is listening on COM6
JasJar has outgoing COM set to 4
When I start a BT sync reports "Cant find existing Bluetooth Partnership that supports activesync." and asks for a search.
Run through the wizard and select my PC and its serial port. After finishing device will not start a connection.
Go back to activesync and try to connect via bluetooth and gives the "cant find partnership error.
Tried two different adapters on the PC and neither get it to work.
Anyone with any ideas?
Thanks!
Remove all the BT setting you have setup. Just follow the Help file on AS4.1 it works, really!
Tried all that and still not working.
Device just doesnt seem to initiate an outgoing connection.
ActSync connection problem!!
Did you fix the connection problem, think we are living the same case.
If you did fix would you please tell me what was the way?
thanks!
@Dave
From the PC AS, select File>Connection Settings and uncheck USB connection and select the BT COM port for Allow Connections. Then select "Connect" and wait till it tries all the connections and fails. Then selec Cancel and then try to connect from your Universal.
PS - I am assuming you have set-up the BT pairing using the Control Panel on the PC and Added the BT COM port from there as well
Hi,
Tried your suggestion. No luck.
PC is setup correctly. AS listening on COM6 (BT AS port as shown in my local services)
Jas doesnt seem top even initiate an outgoing connection. Get no blue indication on my desktop icon or on the port status item in the control panel.
Sorry to keep asking questions, but when you set-up the pairing between the PC and JJ did you get a Wizard on the PC that identified the ActiveSync service? Does the pairing info on the JJ say the PC provides a ActiveSync service?
I've had the same problem with my M5000, just solved it.
I removed the Toshiba bluetooth Drivers from the system and rebooted. WinXP SP2 found new hardware and proceeded to install what I assume to be standard MS Bluetooth stack. (DellHardWare.jpg)
Next, I deleted the bluetooth partnership from the M5000. I created a new partnership with my laptop, but initiated from the M5000. At this point, the M5000 didn't offer any services to use with the partnership. So, back to the laptop, creating a new incoming COM port (COM8),(DellCom8.jpg) and then set Activesync on the laptop to use that newly created port. (DellAS_connect.jpg)
Back to the M5000 bluetooth partnership, select the newly created partnership and click refresh (M5000btooth.jpg) This Time it offers me the activesync service. Tick the activesync service and then save.
Finally, on the M5000, from activesync select bluetooth connection...and that was it. Still working. Once I've disconnected and soft reset I'll try to make the connection again and report back. I'll also try to use the M5000 as a wireless modem and post results here.
FrankyG, great news. But I think the procedure you described is not that different from the AS44.1 Help file I suggested earlier.
i do it, but i doesn´t runs
Delete all your BT COM in control panel/system/device manager (select view and show hidden devices) by going to safe mode. Afterwhich restart your PC and try to pair again....it's always works for me
will someone please help me in configuring active sync over bluetooth..
i want to connect my jasjar with my pc over bluetooth.
when i search in the bluetooth of my jasjar the computer is shown in the devices but in the service there is no activesync
Hi I was puzzled with this the other day. I found that if you open ActiveSync and click Menu then Connect via Bluetooth. It worked fine then.
Hope this helps
B
Before you can connect, you need to make sure your PC has a bluetooth com port. Then in ActiveSync, enable connection via that com port.
Once that's done, you can use the connect via bluetooth on activesync on your ppc, and you can choose your pc.