Can't Edit some registry settings after AKU 2.0 - 8125, K-JAM, P4300, MDA Vario General

I can't change some of my registry settings after I flashed to the new Qtek rom (I have a Cingular 8125)...
Why am I blocked from changing these settings? Ext Rom issues? How can I get around them?

which settings? I'm using the latest K-Jam ROM and I have run into that yet.
-Mc

I'm trying to enable ClearType in Landscape mode
==================
Enable ClearType in Landscape Mode:
Go to: HKLM\System\GDI\ClearTypeSettings\OffOnRotation
* Change Value from 1 to 0
==================
When I try to change this setting I get the following message:
"Error Setting Value: Access is Denied"
It also happens with a few others I have tried, but not with all settings.

I also get edit the setting to force GPRS to stay connected all the time. This is getting really annoying

I have the problem with my backlight settings.
It can only be on 10sec or off.
When I put it on 30sec and go into suspend it will be on 10sec when I start the device.
Qtek 2.17 New Rom

does it allow you to change the setting and when you go back in, it's reverted back to the original setting?
If this is the case, give me a reg key that you're seeing the issue with and I'll give it a shot...
-Mc

I really hate issues like this that no one has any knowledge about...

Related

Registry edits get reverted after reset

Does anybody know why this happens:
Whenever I change registry (for example HKCU\Control Panel\SIP\..), after reboot it gets reverted to original value.
I used Total Commnader. Roms I tried: 2.17 (qtek) and 2.24 (cingular).
Help appreciated.
Thanks.
after changing your registry, be sure to save the changes by a soft reset. To do this, do NOT poke the reset hole with your stylus, but rather shut the device down with the on/off button. Hold it for 5 secs untill the warning pops up. By resetting this way, your device uses the 5 secs untill the screen pops-up to write the registry to the ROM. If you soft reset immediately with your stylus after chaning the registry, the device has not enough time to write the changes to the ROM. Therefore, after a quick soft reset with your stylus changes might not be saved and the registry remains unchanged.
Problems with Registry settings
I also have problems with Registry settings. For instance some values seems to change back after a turn off/on (power button). Does anyone have a good doc/link that explains which Registry settings that actually can be changed by CAB-files and stay changed ?
Just to mention - on an SP5 (sorry for this in Wizard/K-JAM) I had a CAB-file that changed the Contacts soft-button into starting a 3rd party application. This only changed when an incomming call/phone application was started..a little confused about that

Problem: Cleartype is on in Landscape

Hi
I've tried MrClean 2.24a and the latest 2.26 T-Mo ROM and they have the same weird bug: as soon as I use either Tweaks 2k2 or Registry Wizard, Cleartype starts working in landscape mode. I did *not* check "enable cleartype in landscape mode" in either applications and the OffOnRotation registry key's value *is* 1 in the registry (I know, weird). The problem is, that I don't want cleartype in landscape, only in portrait......what do I mess up?
Anyone?

ClearType

One side-effect of this latest Dopod-gps-rom is that ClearType is disabled, and there's no control panel applet for it.
I have set the correct registry values to enable it nonetheless, but it gets disabled again after soft-reset.
Is there any way to permanently enable cleartype, or to stop the soft-reset changing these values? Where do I start to look, extended rom?
thanks!
Edit:
* Solved: I was looking for ClearType applet, but this setting is also in Settings|System|Screen|ClearType
* Solved also for Landscape modus: http://forum.xda-developers.com/viewtopic.php?t=15688
Make sure you made the change to the following registry key
\HKLM\SOFTWARE\Microsoft\Shell
Change the value for NoClearType from 1 to 0.
This unlocks the ClearType option.
You may then go to Today->Settings->System->Screen. Now the ClearType tab is shown and you can enable it there.

backlight Manager MVBklight 1.4.2

Hello, i was looking for a standalone backlight manager to use in ultimate launch ( with cycling ) and i've found this great stuff on 4pda.ru but unfortunately it's all in russian. I've manage to make it work well on my trinity but i'can't understand all the options and there's no .ini nor lang.text to edit. Some help is welcome for the translation, even if you don't translate the program i would like a russian helper that can list all the options (would be perfect with screenshots). thanks a lot for viewing perhaps helping !!!
P.S. :sorry for english, when you read my posts you know i'm french ; )
UPDATE 06.05.2008 new cab below containing the english mui.cab. Install both then go to config first line of the second tab to change language. All credits to MalVal
MVBklight 1.4.3
1. Install MVBklight.CAB.
2. To change the language: install MVBklight.MUI.CAB, go to settings the first line of the second tab.
3. To change the skin: copy a new skin to Skins folder in program folder and choose this skin in settings.
Thanks a lot it works perfectly now i can configure my cycling function. your great
Your program is really perfect MalVal, I was looking for a stuff like that for a month, really happy that the Dev himself answer me. The torch, the cycling function, the today plugin, the fact that it's multiplatform, nice work. Do you have made other progs ?
Yes. MVBalance. It dysplays remained money in your mobile on today.
But it have only russian interface, and i think it will be difficult to adjust it.
Hi MalVal,
Did you have a short tuto ? How does it works, I launch it, change langage, but did not understand how to make it works!
Thanks for your help
Universal backlight manager MVBklight.
Features:
- System WM2003, WM5/WM6, qVGA, VGA.
- Control of backlight from the today (joystick: right - increases, left - decrease, central button - the settings menu, up / down go to next plugin).
- Popup with backlight regulator (joystick: to the right/up - increases, to the left/down - decrease, closing by the central button).
- Set and get of backlight from a command line (the example, ‘ Cmd 244 ’ - set new, Cmd - returns current).
- Increase/decrease of backlight from a command line (the example, ‘ Cmd + ’ - increases, ‘ Cmd - ‘ - reduces).
- Switch backlight from max to min and back ('Cmd m').
- Cycle change of backlight through Cmd.
Cmd 2 5 7 10 on a circle changes values. If was < 2 sets 2, if < 5 sets 5, ..., if >= 10 sets 2.
Similarly with decrease, Cmd 10 7 5 2 - if was more than 10 sets 10 if > 7 sets 7, ... if <= 2 sets 10.
- Switch on of the necessary backlight at connection to an external power (only if plugin is active) and switch back to battery backlight.
- The torch mode, switch on the maximum backlight and the white fullscreen (Torch.exe in a program folder).
- Settings of colors.
- Support of skin (32-bits RGBA bmp).
- Various kinds of sliders (without skins ).
- Display of backlight value by number or in percentage.
- Possibility of manual input of dwIoControlCode codes (see DeviceIoControl in MSDN) and the registry keys which are responsible for set and get of current value of backlight (these codes and keys differ from a device to device).
Installation:
1. Install the cab in the main memory (not on storage)
2. Start from Start-up-> Programs-> MVBklight or from explorer \Program Files\MalVal\MVBklight\Cfg.exe, make settings.
3. In the same place, in settings switch on a plugin.
Settings:
1. At the first start in line "Settings for" there will be a name of your PDA and will be established default settings for it. If default settings does not work, we can manually adjust it.
2. In the field "Type" choose your PDA type.
Input section, branch and keys of registry in which current values of backlight are stored (Battery and power). For many PDA - HKCU\ControlPanel\Backlight, ACBrightness and Brightness.
They can be looked in the registry (corresponding values vary after backlight change by a built-in regulator). In the same place it is possible to find the maximum and minimum.
3. For WM5/WM6 it is necessary to enter corresponding sexadecimal codes DeviceIoControl.
4. Specify a skin folder. There should be four 32-bit bitmas with an alpha-channel (folders should be in a plugin folder).
To find out backlight settings for each concrete device, it is necessary:
1. Find out what file with exptention dll, cpl or any is responsible for backlight on this device (means backlight adjustment through the menu Settings-> System-> Backlight or Brightness ).
Usually this file is in a windows folder and has a certain speaking name of type COMBacklight.dll (on ETEN).
As a last resort, it is necessary to investigate all files suspected on backlight control.
2. It is necessary to copy these files on PC.
3. Then we use IDAPro to disassemble it and try to find options needed.
There are some known settings in attach (my database).
PS. Sorry for my english .
Hi MalVal,
your app did sound so sweet ;-) but unfortunately is does not work on my Artemis.
The slider shows up - but it does not change the brightness no matter what I do.
A couple of observations:
it shows Arte20000 instead of Arte200 and this name is fixed
for device type it says WM2003 but it should read WM6.1 or at least WM6
most of the settings for registry are greyed out and not changable
Might be that the problems come from my Rom being modified ?
Best regards,
mst
Hi MalVal,
Same issue for as mst46. I'm using your soft with Artemis PDA and "ARTEMIS TOUCH 4.01 WM6.1 WWE ROM".
As previously mentioned, only ARTE10000 is proposed and no way to modify other fields as they are "greyed".
BUT, it seems that is it because of the english translation you quickly done. I try removing the cfg.exe.mui file you provide, and then relaunch conf, then, even if written in a langage I cannot understand (russian ?), it is possible to select another item than "ARTE10000" and then are able to edit the following fields.
I try to select WM5/WM6, then HKCU, then ControlPanel\backlight, then Brightness, then ACBrightness, but seems that it has no effect. Difficult to o further when don't know what are the files editing
Could you take a look at it ? Thanks for your support.
Same thing happens with ipaq hx2490b. The device name is correct, the OS appears as WM2003(I haveWM6.1), and other options are greyed.
If default settings does not work, you can manually setup it :
1. Set manual in field Settings for
and restsart Cfg.exe. All fields become accessible.
2. see post above.
Known codes for some HTC:
HTC Hermes, НТС Х7500:
Codes: Pwr - 0x220010, Bat - 0x220018
HTC 4350 Herald:
HTC P3300:
HTC 3400 :
Pwr – 0x8, Bat – 0x7
Registry: HKCU\ControlPanel\Backlight, ACBrightness and Brightness
HTC Wizard:
0x2
HKCU\ControlPanel\Backlight, ACBrightness, Brightness
iPaq 3715:
Battery – 0x7, Power – 0x8
Registry the same
You can try these. If it does not help, it is necessary to analyze built-in backight manager with IDA.
Hi Malval,
I've been able to make it work with the parameters you provides for my P3300.
But there is still a problem with the translation file I belive.
I first install the Cab, then replace the cfg.exe plus the cfg.exe.mui file with the one you provide in the early post.
When running the conf, it is possbile to have it in english, but it was not possible to select something else than ARTE10000 in the second field (settings for) of the system tab. The "manual" option is not available!
In order to make it works, I remove the cfg.exe.mui file, and relaunch the conf. Then all messages come back to russian, but in the second field of system (settings for I belive it is writen in russian), I was able to select something else than ARTE10000 and I've been able to access following fields (they are no more greyed).
Once the "manual" field selected, I exit the conf, and replace the conf.exe.mui file and I've been able to see what are the fields I was modifying as the langage come back to english.
But, in the "Settings for" field, it is written "(null)", and opening the drop down box, only ARTE10000 is available.
I hope it can helps you in order to modify your code to fix this minor bug.
For those who follow the instruction I gives, and having a P3300 running "ARTEMIS TOUCH 4.01 WM6.1 WWE ROM", I set a "Maximum value" to 4 otherwise you will have a surpise of a blank screen if seting a higher values.
Regards
Hi, JBT1.
Thanks for bag.
I've upload a new one. In the same post. Check it.
I've also add mui for plagin.
In the next release i'll add all files in one cab-file and i'll update database to support artemis.
Hi Malval,
Sounds good this time. Manual is available now in the settings and today plugin menu is in english.
Thank you for this great application.
I have an issue now with the assignement of a button with your popup application. I assign it to the button 6, and it works fine except when running TomTom! If running Tomtom and hitting button 6, it call the default assignment who is the Voice speed dial! I beleive it is a Rom or Tomtom issue.
Will look forward for your next rev
Thank you
I tried it on my Kaiser.
Hanging when changing the backlight.
Working great now on my Artemis. Great tool .
Thank you MalVal !
mst
Can someone post a screenshot of what the actual today plug in will look like? Been trying to get it to work on my kaiser but not having any luck
mattarse, romualdrichard!
I need more information, what is the problem.
Screenshot.
More screenshots in attach. I hope it enough.
please do you have more screenshots of this program?
The backlight doesn't change at all. Im on a kaiser with duttys newest 6.1 rom.
If I leave it set for kaiser it is stuck on WM2003, but changing it to manual and setting it for Wm2005/2006 doesn't help either.
I assume the problem is in one of the other settings, but I reallydon't know what to test.
Any help you can give would be appreciated, I've been looking for a program like this for awhile.

Registry Changes with Script

I am creating a package that runs a script to make changes to the registry of a windows mobile 6.1 device.
can anyone point me in the direction of a list of all registry options and values?
I need to change:
BT Select to Microsoft
Backlight settings to never turn display off
Turn ClearType on
disable the turn of device if not used for..
can anyone help me with this?
Many Thanks
These registry settings are different per device. You will have to search for Your device-specific settings and test them first to be sure.

Categories

Resources