Urgent - MDA II, XDA II, 2060 General

hy
i have this problem with my qtek 2020 conected to an gps antena holux gps slim 236 and the problem is like this after installing the GPS viewer ... it is all oki found it on COM 5 speed 38400 but when i go to IGO trying to open the conection manager .. and selecting the com 5 at the same speed ... it does not see any satelits .... no nothing ... i belive thant is a problem with bluetoot com ports ... so please give me an program that alows me to change the GPS antena bluetooth comport
and please don't send me any BlueTootH Tools i have try it and nothing ...

problem solved using bluetooth manager

Related

TOMTOM ACTIVATE HELP??

HI
i am new to this plaise help
i got SPV M1000 witch i install TOMTOM 4.00
the problem is when i click on tomtom navigator
i get this massage: gps position unreliable
plaise tell me STEP BY STEP how do ACTIVATE GPRS
coz i am new to this
tnx
Nice and easy....
Launch TT, goto config, goto GPS
If you have a little circle at the top right spinning then it's connected to your GPS device, however if you get a popup asking you to pair it, then do the following
Search in BT, you should find the GPS device, pair to it (dont use a code if asked)
Tick the allways connect to this device tick box, ok all the way out and TT should now be talking to the device
It will take a while to initially pick up satelites, you should see some grey bars and numbers in the GPS window inside TT.... Also make sure your outside
Hi King2,
are you getting GPS and GPRS confused?
you don't mention a GPS unit in your post (but you do mention GPRS)-- do you have one? TT is useless without.
the GPS unit (usually cabled/bluetooth) is basically a satellite receiver which TT uses to locate your position.
Hi,
GPS Position Unreliable means that the GPS Module not found any satelites.
When you don't have the module you don't get this message.
Then TomTom says GPS module not found.
I takes about a minute or so to conect to a satelite.
But you must be in a open space otherwise the module can't connect.
When you are between buildings the connection is difficult.
Hope this helps
Greetings [email protected]
COM PORT HELP????
HI
TNX FOR HELP
i upgrade my SPV M1000 from win 2003 to 2003SE and the
GPS TO V 3.07 the problem i got is:
on the bluetouth settings,bluetouth serial port setup:
INBOUND COM PORT:COM4
OUTBOUND COM PORT:COM5
now on the GPS TAB
on the top drop i got TOMTOM NAVIGATOR GPS
and on the second drop i got COM 5
now I CANT TICK THE BLUE CHECKMARK BOX TO START THE CONNECTION but before i upgrade to win 2003SE it was OK
any help plaise and tnx
----------------------------
ROM version:2.06.00WWE
RADIO version:1.18.00
EXTROM versionIAMOND 1.2se
Port Problem
Hi King2,
Did you paired the phone and the BT GPS?
It is where you put the BT on
Settings / Connections / Bluetooth / Devices / New
If you did there was a question about a bluetooth serial port connection.
You must answer yes or no. Use yes
If you tick yes, WM2003SE creates a BT Serial port.
I think in the text it also says what port was created. (i saw in a flash that is was BT Serial Port 5
In TomTom got to GPS and take BT Serial on Com 5
Uncheck the port 4.
I din't change the settings and when i just looked in the BT Settings only the Outbound Com port: 5 is checked and 4 is not
I hope this helps
Greetings [email protected]
COM PORT HELP???
HI
TNX FOR HELP
NO I CANT paired the phone and the bt gps: DEVICE NOT FOUND
I DONT get any question about a bluetouth port connection
but in TOMTOM GPS I DO TICK THE COM 5 in second drop
the problem is i CANT TICK THE BLUE CHECKMARK BOX TO START
THE CONNECTION
is ok with COM 4 but no COM5
COZ IF I CANT TICK THE BLUE BOX TO START THE CONNECTION
I CANT PAIRED?
any chance to change the COM PORT settings in BLUETOUTH SETTINGS?
tnx again for your help
Hi King2,
You must pair your BT GPS otherwise it won't work.
What for BT GPS do you have :?:
And did you put the GP on when you try to pair. (it a silly question but i have to ask you).
Did you BT GPS came with extra software :?:
Were going to get it to work :wink:
TOMTOM GPS
HI [email protected]
tnx for your help
IT S ALL WORKING NOW
i did paired them and it s working like dream
your r top man

Bluetooth GPS COM Port problem

Hi, I have a brand new XDA Mini, but with Qtek S100 WWE Rom 1.12, and I bought a Bluetooth GPS, Xaiox NAVOne 2.0...
Bluetooth manager can see the gps without problems, but my Medion2004 Navigation Software says, no GPS is avaiable.
I've already read in the users manual, that GPS needs Com8.
As I see in Start -- Settings -- System -- Bluetooth settings, xda mini has Com5 for outbond port, and Com4 for inbound port.
How can I change ? No program is running, if I check.
Please, help me, thanks.
Nobody has a good idea ? I have already tried the Pocket Bluetooth Tools, it can give a solution, to change COM port 5 to COM port 8, my bluetooth gps requires this port.
BUT, this screenshot appears only a small moment (0,1sec) when I install NAVone2.0 gps...
I installed this gps 100 times, everything is the same.
Can you suggest me another bluetooth tools application?
The problem is simple, to change COM 5 to COM 8.
Thanks in advance.
You could try installing gpsgate from franson
http://franson.com/gpsgate/
change software!
I think you should try change software. I have tomtom 5 to my s100 and it works just fine..

TOMTOM 5 AND GPS HELP?

Hi
I Got O2 Xda Wm 2003,tomtom 5,bt 77 Gps The Problem Is:
I Cant Stablished Contact With A Gps Cos I Got No Port
On Pda Bluetooth Setting.
On The Pda Setting I Got>bluetooth Setting>mode>on>off>
Discoverable ( No Ports As Com 2,6,9...)
And On Tomtom Gps Setting I Got,
Gps Is Connected To:
Infrared Port
Bt On Com6
Serial Cable On Com1
Com9
Com2
Serial On Usb.
How To Add Com Ports In My Pda
Tnx For Your Help
ITS WORKING 100%
I GO IT WORK
Hi,
I have the same problem - no virtual COM port - how did you make it ?
I tried every setting in TOM-TOM and nothing changed. Please help me.
TOMTOM AND GPS
The XDA II comes only with support for BT headsets and ActiveSync through BT. The serial port emulation is also a feature of the Microsoft BT stack but you need a device driver a register port and to handle it
AND ITSOCKET BLUETOOTH TOOLS

Universal + BlueTooth GPS problem, help

Dear Htc fellows,
My bluetooth GPS is working strange on my Universal, but on iPaq with
WM2003 works as a charm. The BT GPS is new Solar GPS with new Mediatek
chipset.
It's not working with iGo 2006 and even not Tomtom 5 or Tomtom 6.
I can find the BT GPS in BT manager, I can pair it, but I dont know why,
it needs a pass key even if it shouldn't. Then when I explore it's
services, The popup come again asking me if I will allow external BT
device to connect to my Universal and it come asking passkey again (Why?).
I can't even enter an empty passkey (bt device doesen't require it). After that I have successfully paired the device. I can add it's serial port to enumerate on com ports 8 or 4.
When I start Tomtom, it doesent detect the device at all. If I use iGo, it detects, gets datas and disappear, it's allways appeared for 1 second and then 5 seconds not. No matter Which bitrate I set (device is written to be 9600) it needs to be in NMEA protocol, not SIRF.
When I use some freeware GPS programs, it seams to be working ok, it shows satelites and it's not disappearing.
What can I do with that???
I have some idea that it's probably about WM5 and it's security....
How can I setup com security in registry? can I set the port speads manually atd... I had performed a hard reset and it still don't work. Can ROM update or AKU update help me?
Does anyone have some idea what should I try now?
O2 XDA EXEC:
Rom: 1.30.107
Radio:1.09.00
P:42.42.P8
BT GPS: model: BT 2.5MR
made by f-tech.com.tw
Thanks;
Shef
Could you find a solution??
Hi,
I have the same problem exactly and could not find anything on the net. Did you solve your problem?
well ...
i know that there is a problem with GPS and WM5 and so there is this patch which i install every time i hard reset .....
the guys i bought MY GPS from gave me this ... and they are pretty knowledgable .....
it works well ....
try it !
tried
My OS version is WM2003 but tried anyway.. Did not work.. can there be version for WM2003??
did you ?
did you define an outgoing com port for the device (com 4 for example ?)
com port definition
well, igo finds the device an COM 6 actually, it connects too.. but stays connected just for a second, then again and again..
I installed GPSGate and created a virtual com port 7. I manually configured the GPS receiver connection to COM 7 on igo.. But all the same.. :
do you advice another way?
one other thing the device works with navigon 5.0 and tomtom 6.0 smoothly, no problem.. only igo..
well...
IGO is CRAP ... that is well known .... lots of bugs ...
i am sorry .. i do not know how to solve your problem...
but i suggest using destinator 6 ..... (that's what i use) ....
simple ... nice looking .... big buttons and able to navigate to your contacts directly (especially useful if you have Phone Edition)
oh ... and ... works great !
I got the Holux GPSlim 236 GPS. I can pair the GPS with Universial. But I cannot set the com port at all. A pop up window always say the com port (I tried everyone of the ports) is not available.
Any one got a solution, does the GPS bug fix help ? and what does it fix ?
Might seem a bit obvious, but have you tried the code "0000" when pairing your device?
Once paired...did you define an outgoing serial port on "Bluetooth Settings" menu on your WinCE?
I have a royaltek bluetooth GPS and it's been working well with TomTom[5|6]...I use '0000' as passkey (default on many 'non-interactive' devices), once paired I clicked on 'COM Ports' tab and defined a new outgoing port, the wizard should list the GPS as an available device to create a COM port so I used it and I got a 'com0'.
Once the outgoing port was created I had to tell TomTom to use the new 'com0' and worked like a charm
It's been working since TomTom 5.21 (previous versions didn't work).

xda 11i com port problem

hi
i have the latest rom for my xda but i cannot get my bluetooth gps receiver to be seen , it will bond but it does not seem to find the com port , i have a holux 236 and i am running gps viewer:confused which scans the com ports , it used to find it but since a reboot it will no longer do so.
i have tried wm5gpsfix but it seemed not to do anything.
anyone any ideas
cheers
martin bell
[email protected]
I had the same problem but with WM 2003. Instalation of Widcomm Bluetooth Stack maked my GPS receiver visible for TomTom application. try that!

Categories

Resources