I have two devices Wizard(qtek 9100, 1.1.7.9) and HP 2110. Error (сan't connect to ..) happens when I try to send file VIA BT from hp to wizard.
Option "receive all incoming connection" in IR settings enabled.
HP 2110 have WIDCOMM BT stack. All neccesary options have been enabled. File trnsfering works with another PDA device (wm2003, widdcom).
PS: Dial up networking via BT doesn't work too
Hi -'Option "receive all incoming connection" in IR settings enabled.' that for infrared.
In settings\bluetooth make sure bt is on and discoverable and you need to pair devices first in settings\bluetooth\devices.
Should work then If not trash your hp lol
Thanks. But option "discoverable" has enabled. In several forums i have seen that IR option "receive all incoming connection" must be enadled too. I think this is problem in communication beetween 2 different BT stack, because I have problem with dialup connection via BT too.
Has anyone had such problemm?
Is there any way to to have this option checked by default "make this device discoverable to other devices"...everytime i switch bluetooth on and off using Phone Profiles this option gets unchecked..
Thanks
VJVolubilis will do this I think.
V
Hi all,
Searched under 'bluetooth' with no obvious joy.
When I turn on bluetooth I have to manually make sure that the device is discoverable every time if I want to receive via bluetooth. Is it posible to make the device 'discoverable' automatically when I simply turn bluetooth on?
Thanks.
Matt
Well I'm surprised at you all! lol.
Sorry guys, been away (pc problems!! still ongoing but at least now I can connect to www) so not been watching the site.
Anyone any ideas on this?
Matt
I think you have to tick "receive incoming beams" under connections
mb5049 said:
Hi all,
Searched under 'bluetooth' with no obvious joy.
When I turn on bluetooth I have to manually make sure that the device is discoverable every time if I want to receive via bluetooth. Is it posible to make the device 'discoverable' automatically when I simply turn bluetooth on?
Thanks.
Matt
Click to expand...
Click to collapse
All I did was go into bluetooth settings, make discoverable, and everytime I power on my BT Headset, it automatically connects.
mb5049 said:
Hi all,
Searched under 'bluetooth' with no obvious joy.
When I turn on bluetooth I have to manually make sure that the device is discoverable every time if I want to receive via bluetooth. Is it posible to make the device 'discoverable' automatically when I simply turn bluetooth on?
Thanks.
Matt
Click to expand...
Click to collapse
Is beam receive switched off? This has been a very common problem with WM5 users before I've published the fix to it.
SiLeNtKiLLa said:
All I did was go into bluetooth settings, make discoverable, and everytime I power on my BT Headset, it automatically connects.
Click to expand...
Click to collapse
It should connect every time you power it up - even without your PDA being discoverable.
Hello!
Unfortunatley ihave the same issue when i'm connecting using Stereo BT Nokia BH-501. The problem is that each time after the BT is switched off and then switched on i need to go to Bluetooth settings and make an update for it and save. Only ofter these steps it reconnects to Hermes (HTC TyTN) and starting to play sounds and music through BT
Is it possible to make it fully reconnect automatically after it is switched on and how?
Thanks!
VJVolubilis can force you into discoverable mode from a shortcut, so you can drop that into your startup folder, but it's not advisable to keep yourself discoverable unless required.
V
Hey VJ
I just tried that... I made a shortcut with the -bluediscoveron paramenter and removed the -status parameter. I dropped it in my Windows\Startup folder.
It doesn't seem to be working, When I turn on my BT, Dicoverable Mode is still OFF. However after, I enable my BT and then click on the shortcut with -bludiscoveron parameter, it works.
Is there anyway to have Discoverable Mode on even after I turn off my BT and then on again?
I have the HTweakC installed on my 8525 (2.06 rom). I can not get the discoverable to stay on. It keeps turning itself off. The bluetooth indicator show "On" but not discoverable. I have all 3 box checked under the bluetooth tab.
So i once paired my phone with my car stereo handsfree, but since it was a $100 stereo, the handsfree didn't work correctly. So i don't want to use it anymore. But the stupid stereo have no way to turn off bluetooth.
I tried deleting the stereo from paired devices, and set my phone bluetooth to "hidden" - but that stupid stereo still finds me, and a message about "bla bla wants to connect" pops up everytime i get into my car.
I also tried disconneting power from my stereo, and use the reset switch on it, which reset all settings on it - but IT STILL FINDS MY PHONE!
Anyone have any suggestions on what to do? At the end of the day, i have like 10 notifications on my phone i have to go through and click "No" on...
On the Wizard did you ...?
1) Push the Comm mgr tab
2) Click on settings
3) BlueTooth Settings
4) Mode: UN-check the box "Make this device discoverable to other devices"
5) click OK.
If you didn't do that, try it.
Then go to B/T settings again and pick devices, and remove the device giving you trouble.
That SHOULD do it.
as mentioned i have already made it undiscoverable for other devices. But it still tries to connect to me...