Related
Has anyone found a utility or a way to automatically dial numbers using a calling card? This is a rather convenient feature in my previous (non-WM5) cell phone that allowed me to import my corporate phone numbers and then use automatic calling card to dial them without editing hundreds of entries in the phone book.
I have noticed the "Callingcard" code sample at MSDN, however, there does not seem to be a compiled binary available anywhere and I do not have the development environment available.
Any help or tips appreciated.
Ihave been using this one
It is one of the importat things for me
so I use Program called "Long Distance Dialer (Pocket PC Phone) 1.3"
it works on WM2003, WM2003SE and I am runing it right now on WM2005
http://www.pocketgear.com/software_detail.asp?id=12595
good luck
DNO
Thanks! I did not realize it even runs on WM5. However, it does not see to go past dialing the access number - goes to reorder / busy tone right after. Is there a trick / fix to it?
I am using it on HTC Wizard
I never had that kind of problem
I don't know how to help you
This is my settings
Name: My card name
Acces#: my number (only numeric )
Dial Seq : PIN/Destination
Wait: 1Sec Pin : My pin
Wait 1 Sec Destination
then I go to Contacts I right click on the name I want to dial , it gives me optioon >> Dial using : then Name of my calling card .
When I click on that it gives me list of the phone numbers unther that name .
Since I call from USA I do need to select option << Add 011 before number >> but I do not do it because I added 011 to all phone numbers that I call with the card , in the Contacts
I hope this will help.
Good luck
DNO
I installed Long Distance Dialer 1.5 on my PPC. I like it so much that I want to register ($4.99). However 1.5 cannot be purchased anywhere anymore. Did anyone manage to purchase a registration key for 1.5? Or alternatively are 1.3 registration keys inter-changeable with 1.5?
This seems like a great piece of software, but it won't seem to accept pins less than 4 numbers. I have all my number listed with the country code first, so I need to add 00 to call them. In the past, I've configured my calling card feature to use 00 as the pin, which works great, but I can't get this to do it and I don't want to manually add 00 to all my numbers!
Many thanks for any help,
Paul
The link is to version 1.3. What you need is version 1.5. A quick Google will give you two or three sources.
1.5 has no limitations, but has an annoying trial notice pop-up each time you use it. Where can I purchase a registration key?
Thanks for the reply. I've downloaded v1.5, but it still won't let me enter a pin of less than 4 digits. Any thoughts?
Many thanks,
Paul
Solved the problem. In v1.5 you can put spaces as well, so, even though it needs at least 4 characters, I can put two spaces and then the two zeros.
Best,
P
Interesting - I was trying to solve my problem with the software dialing only the calling card access number. I defined an address book entry with the whole number with pauses - and still only the access number gets dialed. The card I use follows the "Number followed by PIN" model with a second dial tone after you dial the access number and a third one after the called number. Any ideas what could be causing the issue? Could it be that the Wizard does not recognize that the call has been completed after it dials the access number?
free and the best calling card dialing software
this is reply to betstu2004 request i.e compiled binary from msdn betstu2004 mentioned about
its in cab format and is attached for downloading.
here is the procedure for installing and using it:
1)copy the cab file in ppc and install it
2)then using any registry editor we have to edit the values of number to be dialled and the pin number of the calling card,to do that
open registry editor
go to:
hkey_current_user
then software
then microsoft
then calling card
in this option you have to edit two entries
1st is Number which is your calling card number
2nd is Pin which is your pin number
save the changes
then to use the software
go to contacts
then
with stylus touch and hold the contact(international) you want to dial
you will see an option
call mobile using calling card
click it
and ppc will start dialling using calling card software with stored calling card number and pin
once the card is finished you can input the values of number if different from previous one and pin again
in some cases the new number and pin will only be saved in the registry after soft reseting the phone
you can even adjust the pause time which is 2 sec by default
this software is working perfectly on my xda exec and i hope you all will love it
cheers
My email to the author (VSOFTCODE) of LDD bounced. Looks like I will have to remove it after the trial expires.
Edit: I just managed to purchase a licence through Handango after all.
----->chaniana
Thanks works fine!!
chaniana - BIG thanks - it works flowlessly.
Now - if I could only get it to dial the number before the PIN!
reg key
Well I know this is not a warez site but
would it be wrong if I give out the reg code ??
I think not ,because the software no longer supported by the developer.
what you think ???
One more thing !!
I have Version 1.3 which I bought from www.pockeatgear.com
where did you find v1.5 ???
Let me know
DNO
this is cool....
chaniana , i have been looking for something like this for a while... i have 2003 not 2005 to be able to complie or change this...
I am just migrating form treo 650 and am missing a program TakePhone. what it did it let me create rule
e.g. any number starting with a string it will use a calling card so i could set +44 use a calling card x
that way when i disl a number it will intercept the call an see the first few digits, if +44 it will dialthe calling card and wait for me to hit a button to enter a pin then eait for another button to dial the number, all in a few strokes i was dialing international and never had to change my contacts. when i was there in UK all i do is disabke the rule and voila i am in business...
see if u can do this
i did something similar in VS2003 creating from scratch an app that would list the contacts and i enter a ph and pin in 2 seperate textboxes and hit dial, got it to make a call to the 1800# but could not figure out how to dial the rest automatically so i am stuck
Long Distance Dialer 1.5 at handango.com.
Just pay the 5 bucks, it may inspire others to create affordable useful software!
This software doesn't work with PocketInformant. Any solution ?
I installed Long Distance Dialer 1.5 (Trial), entered Calling card (access#, PIN)
I can see new menu item when I right click "contact", but when I select "Dial CCard" NOTHING happe! No call started.
I'm using Wizard.
Hi
I am not able to see any context menu once I tried using by stylus
I am on WM6.1
Is it still usable
cheers
chaniana said:
this is reply to betstu2004 request i.e compiled binary from msdn betstu2004 mentioned about
its in cab format and is attached for downloading.
here is the procedure for installing and using it:
1)copy the cab file in ppc and install it
2)then using any registry editor we have to edit the values of number to be dialled and the pin number of the calling card,to do that
open registry editor
go to:
hkey_current_user
then software
then microsoft
then calling card
in this option you have to edit two entries
1st is Number which is your calling card number
2nd is Pin which is your pin number
save the changes
then to use the software
go to contacts
then
with stylus touch and hold the contact(international) you want to dial
you will see an option
call mobile using calling card
click it
and ppc will start dialling using calling card software with stored calling card number and pin
once the card is finished you can input the values of number if different from previous one and pin again
in some cases the new number and pin will only be saved in the registry after soft reseting the phone
you can even adjust the pause time which is 2 sec by default
this software is working perfectly on my xda exec and i hope you all will love it
cheers
Click to expand...
Click to collapse
Hi.
You know how on the mda when you hold the d-pad down on the contacts, after a few seconds a letter comes up? It seems like its there to help you skip to the letter that it lands on, but on my phone it doesn't do that. I stay at the same contact that it stopped on before projecting the letter. All the contacts in my phone are sim contacts, do you think this is the problem, like does it only work for the contacts saved to the phone?
And my second question is, after you make a call that is not on the contacts list, is there anyway to save it to the (sim) contacts without having to copy and paste all over again? My old phone whenever I dialed a number or recieved a call that wasn't on my list, one of the soft keys would say "store" or I could press the menu soft key to "store" into my contacts. Unless I have overlooked it, I can't seem to do that with the mda.
Thanx
Anybody?
This is the only gripe I have about the MDA so far, hoping to get it figured out if there is a way.
thanx
like you said it may be that the contacts are on the sim, transfer your contacts to the phone
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
I have the same problem. Both calls and text messages.
I don't think it matters if the international code is there or not.
Really frustrating not knowing who calls.
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Hmm, I've changed the SIM, but I can't remember if it worked wih the first SIM card.
But a hard reset deletes everything, right?
There are a few things you have to be sure of:
Do not have double contacts, if you have a number (with and without operator/country prefix) twice in your list it will not show any name.
I don't know if this applies if you have a contact on your phone memory and on your sim card. I am sure it does have this problem if you have two contacts with the same number on the memory phone.
For some reason this is logic: On an incoming call, the phones checks it's phonebook and retrieves two numbers and then it does not know what to display, is it contact one, or two?
I hope this helps you out. I did not experience any problems (yet).
AndrewCZ said:
I've had this problem first time the device was initialized (right after opening the box). It might be caused by the fact I didn't have any SIM in it at that time, I'm not sure.
After a hard reset with a SIM inserted, everything started working as it's supposed to.
Click to expand...
Click to collapse
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
samluke said:
Hi there, I'm wondering if anyone else might be having a similar problem with 'caller [or texter] ID'.
Most networks, as I understand it, use the international dialing code when sending out texts and calls, meaning this is usually the incoming number when you recieve a text or call.
I've obviously got people programmed into my contacts who text me but when they do, I don't get their name, I get their number - with the dialling code eg. +447750500500. When I tap to go into the threaded mode, I'll get all previous contact with this person but with them identified only as the number. However if I head to the People tab, then again to see the messages I've sent/recieved with that person, I get the same messages only under the banner of their name and not the number.
I believe calls work fine with the code programmed in on their contact profile.
Anyone know why this is being caused?
Click to expand...
Click to collapse
Hi guys!! i had this problem too but i have fix the problem. what i do:
!) i store all my contacts in my sim card and delete the contacts in the phone.
2)do a hard reset
3)upon doing the hard reset, the phone will prompt you on importing sim contacts and finding your service provider. select both and and press ok
4)now try to call from your house to your phone to do a check.
5)my problem was solved after this
hope it helps!
KraFT_mk said:
Try this....
1. Edit one "test number" in your contacts and remove international codes.
Just put that "test" tel number. without int. codes... And make sure that number is not stored nder another contact. (No duplicates.)
2. Then dial from that number and see if that tel# is identified. If you have just "0xx-123456" then go to #3.
3. Go to registry and change of the Caller ID match rule. (Minus one digit.)
Example: Caller ID rule:8 (Change from 8 to 7 or 6 to 5 .. trailing digits for Call ID match. )
* HKCU\Control Panel\Phone\CalIidMatch value:7
4. Restart and test again...
5. If its OK, than test with SMS.
6. If its OK again , put back your international codes and test again.
7. If not go to no.3
Hope this helps.
KraFT
Click to expand...
Click to collapse
What was happening to me before the reset was a bit different - the phone wasn't able to match anything at all - even a number called from the phonebook and stored in "recent calls" in EXACTLY the same way it's in contact, didn't match to the contact when redialed.
I think that something required for Caller ID to work gets done when the phone is first initialized, and that this step requires full access to the phone module (which the phone doesn't have without a SIM inserted and a proper PIN entered).
hi,
i encountered also that worry,
i set the HKCU\Control Panel\Phone\CalIidMatch value:9
my mobile phone number to test was stored as "06xxyyzzww"
and when i phone my diamond2 from that number
the caller id is recognized
(with showing as +336wwxxyyzz)
i tested from my home phone stored in contacts as 04wwxxyyzz
i rang my topaz its was identfied as my home,
(with showing as +334wwxxyyzz)
i am in france, + is for 00 ,our phone numbers are 10 digits long
(mobiles and "home") ,
to be joined from abroad, you have to dial +33+phone number WITHOUT the first digit "0")
so the "9" value i put in the registry
if it could help you
regards
Hi,
just stumbled over the same problem.
The old phone (HTC P330) resolved numbers from my used format 01234-56789.
Since my contacts are a mess, I have 01234-12345, +49-123456-456, +49 (0123)-456 and so on, it would be a great pain in my ass to switch every contact to +49123-456 (which the new phone resolved).
I compared the Registry-Entry from the P3300 with the TD2 and voila: TD2 was 12, P3300 had the value 8.
I changed the TD2 to value 8, reboot and now I'm happy again, the phone is getting used to my contact list
Regards
Heiko
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Caller ID problem, my solution
I had the same problem. But after a hard reset it seems to work just fine now. Remember to backup your downloaded programs etc before doing this.
Tyven said:
Hi,
I'm experiencing the exactly same problem, that incomming calls or messages isn't shown by name, but only by number.
I'm all new to Windows mobile, but I tried downloading a regeditor, and experimented with different values in the CallIdMatch string. However, no succes.
I live in Denmark, where numbers look like +4512345678, where +45 is the international code. Can someone please tell me, what should be the correct value? The original values was 8.
I have further found that some contacts are recognized. What the difference is between the groups, are however unclear!
Click to expand...
Click to collapse
Hi,
"8" should be the good figure for you, as in France
we have phone numbers +33987654321
and "9" is the good value for me, in:
HKCU\Control Panel\Phone\CalIidMatch value:
Edit: i remove previous "edit"
in fact all my contacts had been erased" so it was normal to have no caller ID?
ps: is your carrier sendind all the figures when you're receiving calls, i mean +4512345678
so perhaps you're encountering a bug .
you should try to backup your device, with a soft like spritebackup(special price for htc owners on their webpage) and experiment an hardreset
and restore
regards
Hi ,
did you ever try to change the following:
RegistryEdit and Decreasing the CallIDMatch from 12 to 7 solved my Issue
See below
HKEY_CURRENT_USER\ControlPanel\Phone" name="CallIDMatch"
Greetings from Slovenia
Hello,
that is my first post so please do not be very critical to my english level and PPC skills .
now this is an old thread but for BULGARIA the correct registry value is "9". Here the mobil numbers are as follows "08xx 123456" (9 digits without the ZERO at the very beginning). that is why the usefull number is that (default for my TD2 was 8). Now after this fix the phone can correctly identify which number i want to dial when i am inserting it by digits, instead of selecting the exact person. i do not know am i explaining correctly but i will try to put some more detail on that. When i want to dial some particular number (for example "08xx 123456") the phone select me the correct contact no matter how i put this contact in memory. with "+3598xx 123456" or only with "08xx 123456". before that intervention the phone identifies me the correct contact only if i type the digits, exactly the same way that i have added it to the memory. So i think that this registry key does not have a universal resolution. the resolution depends on how many digits is using tha particular mobile operator.
i hope that will be helpful for someone who is happy to own an HTC and is happy with it ... like Me
hello,
when someone calls my diamond II
it only shows the number of the caller, but not the name even though they are in my contacts how can i change this so it says who calles by name instead of number..
thanks for any reply
This sometimes happen if you have multiple entries of the same number....then phone shows only number and no name.....Is this happening for each incoming call..or just for few contacts...
for all contacts it happens, but most do have an mobile number and an home number..
can i change anything to fix it? or is it a fault on the diomand II .
Multiple numbers for same contact should not be a problem, but multiple contacts for the same number sometimes causes this....fr me it is working fine, so it should not be a TD2 bug..
pgu said:
Multiple numbers for same contact should not be a problem, but multiple contacts for the same number sometimes causes this....fr me it is working fine, so it should not be a TD2 bug..
Click to expand...
Click to collapse
all contacts have just one mobile number and one home number so i don't know where to search a solution
but thanks for your reply
Try to not use the prefix.
(+countrycode)
Should do the trick
this was discusserd once already (I think. I can recall the drop the prefix solution). Search a bit. alas, I will give you a link if I find one
Im having a similar problem. The caller id dosent work for some of my contacts, both when they phone me or when they send a SMS. Im sure they are saved in my phone and not on my sim and from what I can see there isn´t any difference from how they are saved in my phone book from the ones that the caller id works for. Its really strange and annoying. Hope someone has a solution for this problem.
Did you try just delete that contact and make it again. I know it's stupid question but ...
prdic said:
Did you try just delete that contact and make it again. I know it's stupid question but ...
Click to expand...
Click to collapse
yes i did. I also tested to make a new contact from the sms view with the option save contact with the actual number that shows instead of the name and it still didnt work. Thanks anyway.
Hey,
I've had the same problem since day of purchase. I did the reg edit to increase the numbers the phone looks at to identify a number but it still didn't work. I've also deleted and re-created the contacts with no success.
ALL,
I had this problem. I submitted the case to HTC Europe but I did not even get a call back after a few months had passed.
Unfortunately the only way to do this is to hard reset the phone.
You will loose all your phone data (contacts etc) but the files on your memory card will be ok.
When you reset the phone, even if you have NO contacts at all on your sim card, you still have to tell the wizard on the first boot to import your SIM contacts. This, for some silly reason, is the only way to get the phone to register the phone contacts from your phonebook, even if you are just using the non-SIM contacts.
I had no numbers on my SIM card and of course I did not select the option to import my contacts. I was going to do that myself via Outlook. Once I selected not to import the contacts, not one number was recognized.
I did a Hard Rest. If you have numbers or not on your SIM does not matter. Allow the initial start-up wizard to import from the SIM. Then continue.
This solved this VERY ANNOYING issue for me. I used SPB backup first to take a copy of my phone data before the reset.
- Geoff
i had this problem too, solution is change registry:
HKCU\ControlPanel\Phone\CallIDMatch:9(DWORD)
this means phone will identify number by 9 last digits - meaning its ignoring country code.
*if 9 not working for you try 10/11/12... one of these should fix.
bnm7bnm said:
i had this problem too, solution is change registry:
HKCU\ControlPanel\Phone\CallIDMatch:9(DWORD)
this means phone will identify number by 9 last digits - meaning its ignoring country code.
*if 9 not working for you try 10/11/12... one of these should fix.
Click to expand...
Click to collapse
hello
today I tried all the numbers, from 7 to 12
11 was the value that made me look some of my callerID. now I have the same problem, but not with everybody, but only some people
let's say a 50% of my contacts are shown on the screen when they are calling me/sending me an sms, but the other 50% doesn't show me the name but just the number.
today I tried with my mom's phone to call me. it didn't show the name. So i deleted her name from the contact, and added it again (from the missing call). now it's showing her name... Do I have to do it with all the phonebook?
is there something I can do to fix it? it's making me crazy
please help me..
I have, absolutely same problem, erasing the contact and creating it again, did not solve, very very strange. I've tried iterchange of numbers home>work, work>home, work> auto, home > auto, invane, some of contacts refuse to display name, compared the phones i have no same numbers for names ecc. First of all i have to mention that numbers have been migrated from Nokia 6230i via Outlook Express > Outlook > Phone , some of the numbers like Home, Bussiness Fax ecc, did not passed to Diamond 2
I've just noticed that a Hotfix was released a few days ago, which just might solve this problem.
Titled: Update for HTC Touch Diamond2 for Caller ID Display
I haven't tested it yet, so let us know if it works for anyone
try to make all contacts same format with TrineFix or similar app,
set numbers without country code, for example in israel i set 05XXXXXXXX instead of +9725XXXXXXXX, then i change CallIDMatch to 8.
this is how it works for me.
I had a problem with none of my contacts names coming up when they called me, it would only show their number. After x2 software resets and installing everything again I found the problem, when you do a software reset and you turn the phone on for the first time when it asks you to import from your sim card contacts DONT DO THIS if you sync your phone with Active Sync and outlook contacts as this is where the problem is.
If you import your contacts from your sim and you sync with outlook then your caller id's will not work.
If I try to dial a german number beginning with "01" it always sends me back to the homescreen.
I can dial all other numbers except for numbers beginning with "01". But all mobile phone numbers in Germany start with "01" so its a big problem for me.
Can anyone help?
I have the same problem, it´s just not "01", it´s several numbers like "25", "02". I also did a factory reset, and it changed the numbers, before it was "07" and "05" but now they work and others do the same thing. I phoned up the place where I have to send the phone for repair and they said it´s most likely a software issue, it happens when new phones come out. So yeah, call the shop where you bought it from and they will tell you what to do and who to contact for further details. Best of luck!
Edit: I fixed it BY MISTAKE! (lol)
My solution: I delete all my contacts (because I didnt want to send it in with the contacts) and then I tried it out and it worked! I also noticed every time I clicked the green button to call someone, it was on the tab "contacts" instead of "dialler". Another thing, before when I typed "25" I was sent to my homescreen, but not that I reset all my contact when I type "25", one of my numbers appear highlighted with "25" so I am pretty sure that there was a glitch with some of my contacts and now it doesn´t bug up. Try it out and let me know =)
Solution: Delete all contacts, restart, copy contacts back from sim! Voila =)
I had a similar problem with my Milestone 2 when I dialed "22". The dialer would simply close. After some experimentation, I found that the problem only happened when my Facebook contacts were hooked into the phone. By chance, I found that my first Facebook contact had put a non-numeric phrase in his mobile telephone number field on Facebook, and once I had unfriended him, and reset my contacts, then everything worked fine.
So if the dialer is shutting unexpectedly, then checkout whether any of your contacts have a non-numeric phone number.
Hope this helps.
Cheers,
Steve.
I've got the same problem when I type +3939, it's a big problem because I'm Italian!
No problem by typing the numbers you posted before.