Related
Ok having major problems with this unit, I've finally bonded the device to the xda 2 and have installed the software and UK maps onto memory card, I can only select com 7 in the bluetooth profiles for the Navman and when I go into GPS settings in SmartST com 7 is the only one I cant use WTF !!!!!
Also after running SmartST when I next try to run it it runs so slow and eventually locks up I've tried all the patches to no avail I have 70 Mb of memory for running programs so that should be plenty. Anyone haave any Ideas????
Navman problem fixed!!!!!!
Well I managed to figure out what was causing the SmartST software to run rediculously slow on my XDA II.
I noticed that whenever I stopped all programs from running, the Active program would always end up as not responding so I decided to remove the O2 Active user interface and it cured the problem.
It works great totally impressed with it.
WOOHOO
Jarran said:
Ok having major problems with this unit, I've finally bonded the device to the xda 2 and have installed the software and UK maps onto memory card, I can only select com 7 in the bluetooth profiles for the Navman and when I go into GPS settings in SmartST com 7 is the only one I cant use WTF !!!!!
Also after running SmartST when I next try to run it it runs so slow and eventually locks up I've tried all the patches to no avail I have 70 Mb of memory for running programs so that should be plenty. Anyone haave any Ideas????
Click to expand...
Click to collapse
Sorry mate , do you have a smart ST professional ora higher version ?
I'm using the Smart ST professional updated , but I bond the gps with the XDA2 , but once Ilaunch the software , I cannot selectany port available in the gps software .
Do you have any idea ?
Thanks
Smartst
I have the Smartst version 2 which has been patched to the latest update.
Re: Smartst
Jarran said:
I have the Smartst version 2 which has been patched to the latest update.
Click to expand...
Click to collapse
So do I have to buy Smart STprofessional 2 to make it work ?
Thanks a lot
Janaro
Com 7 Port For Navman
I had a similar problem. I had to remove the exisiting bond with the Navman and then soft reset. Then, go into GPS settings and com7 should be available to select. Finally, rebond with Navman device and select com7 from the bluetooth tools options, and hey presto! It took some trial and error but it was worth it, Navman now working perfectly, am looking forward to an extended road test in northern France this weekend!
Re: Com 7 Port For Navman
kernow said:
I had a similar problem. I had to remove the exisiting bond with the Navman and then soft reset. Then, go into GPS settings and com7 should be available to select. Finally, rebond with Navman device and select com7 from the bluetooth tools options, and hey presto! It took some trial and error but it was worth it, Navman now working perfectly, am looking forward to an extended road test in northern France this weekend!
Click to expand...
Click to collapse
I have uninstalled the software and installed again , without bonding it yet .
When I launch the smart ST professional 1.91.0011 , there si no port available !!! do you know why ? Can you help me on this matter . Thanks
Janaro
hey hey hey... cool it guys..
I helped a customer set this up, and it worked like a charm..
You have to make sure that before you paired both the deviced, you have to checked the inbound port under settings->bluetooths settings...
then you should be able to selected it later in the program..
oh yes, just a gentle reminder, just install the EnableCharPin software from , else you cannot enter "NAVMAN" as a password.
Cheers
there is another solutions dou, but after I worked on it for another customer, I could not get it to work with his headset using bluetooth.
ChaoZ said:
hey hey hey... cool it guys..
I helped a customer set this up, and it worked like a charm..
You have to make sure that before you paired both the deviced, you have to checked the inbound port under settings->bluetooths settings...
then you should be able to selected it later in the program..
oh yes, just a gentle reminder, just install the EnableCharPin software from , else you cannot enter "NAVMAN" as a password.
Cheers
there is another solutions dou, but after I worked on it for another customer, I could not get it to work with his headset using bluetooth.
Click to expand...
Click to collapse
Thank you very much mate for your effort , but to be honest ...still doesn't work !! I have no port available in the Smart St Professional window !!! I have done all your path several times , no sign . I have also tried the other bluethooths tools , nothing . I launch the softare but no port available . I can pair the devices but then I cannot get the GPS signal to the software !!Any other idea ?
Janaro
Navman problems
Hi guys -
I'm also having problems with setting up my Navman 4410. I had it working on my XDA2 (after a struggle) when using ROM version 1.03, but I've now upgraded to ROM V1.60.50 which is the latestest relase from 02. Since then I'm having the same problems as Janaro - there is no com7 available in SmartST (v2.00.0029 SP1). The default bluetooth com port is COM4 but it does not appear to bond correctly.
I've tried the recommendation from Kernow but I still cannot get it to work
Has anybody got any ideas ?
Alan
Have you got "Recieve all incoming beams" unticked. Start\settings\connections\beam.
Hope this helps
Receive all incoming beams is ticked - should it be ?
I think the problem is more to do with the COM ports. BTHtools only allows you to set the com port to COM7 - but COM7 is not available within Navmans SmartST software.
Ah ha - untick "Receive all incoming beams" (in start\settings\connections\beam) and COM7 becomes available within SmartST - everybody with problems please note !!!
It now works OK - many thanks
Alan
crippsa said:
Ah ha - untick "Receive all incoming beams" (in start\settings\connections\beam) and COM7 becomes available within SmartST - everybody with problems please note !!!
It now works OK - many thanks
Alan
Click to expand...
Click to collapse
hello there , my incoming beams was already untick !!! still not working , what a mess !!!
Thank you
Janaro
Different Navman solution
After upgrading my Qtek 2020 to 1.66, SmartST would take forever to open whereas it had been reasonably quick before.
I was successful in making it work by not installing the bluetooth tools but only executing the EnableCharPin from my synched laptop.
This meant that I could pair my Navman 4410 after having checked both inbound COM4 and Outbound COM5 in Bluetooth settings. (The bluetooth tools would only provide COM7 whereas that port was not available in SmartST)
The double blinking only went away after SmartST was started.
After installing SmartST V2 the program starts fairly quickly
[/b]
Re: Different Navman solution
LarsN said:
After upgrading my Qtek 2020 to 1.66, SmartST would take forever to open whereas it had been reasonably quick before.
I was successful in making it work by not installing the bluetooth tools but only executing the EnableCharPin from my synched laptop.
This meant that I could pair my Navman 4410 after having checked both inbound COM4 and Outbound COM5 in Bluetooth settings. (The bluetooth tools would only provide COM7 whereas that port was not available in SmartST)
The double blinking only went away after SmartST was started.
After installing SmartST V2 the program starts fairly quickly
[/b]
Click to expand...
Click to collapse
Ok , so I have to install Samst ST V2 !!!
Thank you
Janaro
4400 and XDAII works OK
I am using the 1.60WWE 02 ROM (Recent upgrade), a Navman 4400 and Smart ST (not 2) software, and it works a charm. I agree that BTTools should not be used but you have to use enablechar.exe to key in the PIN. I had no problems with bonding. Make sure however you un-pair all other devices (headset etc) first to give the 4400 first choice of the COM ports. As has been stated, when paired, make sure you check Com 5 outbound under Start/Settings/BT Settings (this was the main feature of the 1.60 upgrade that appealed to me), then select the same port from the GPS status screen of Smart ST.
It is working for me. I look forward to seeing Smart ST2 with its 3d view, but it is not necessary.
I think you have other problems if ST 1 doesn't work.
On another note, the amount of time taken to start the software is related to how many maps it has to process. If you only check the maps you are using (under Setup/Maps in Smart ST) it will speed things up greatly.
After first getting my XDA2 to work with my Navman 4410 using SmartST V2 and BTHTools and setting the com port to 7, I have now managed to get it working by using the standard set-up as recommended by Camstech.
By checking both the inbound and outbound boxes in start/settings/system/BlueTooth_settings and by setting COM5 within SmartST it now works fine.
Alan
Navman 4400 / 4410 and Bluetooth Headset
Very helpful dialogue here. Many thanks to all. Based on this, I am planning to purchase either a Navmean 4400 or 4410, but wondered if any of you have been able to set up the GPS and a Bluetooth headset at the same time. I don't really need to have the GPS voice prompts come through the headset (probably too much to ask at this point), but would like to be able to answer/end calls via the headset, while the GPS is active. Do any of you have BT headsets working with the 4400 / 4410 installed?
I have Navman 4400 and bluetooth headset working at the same time not a problem. I bought Namvan 4400 from Dicksmith Australia as I got it $100 off the price as it has the old 2D software mapping, but Navman Australia send the mapping software upgrades to you for free, something to consider if you can find 4400 still as the hardware is the same with 4400 and 4100 navmans.
Hi
I'm new to this site and would like a little help if possible.
I recently went from an IPAQ 5550 to an XDA. I installed my TOMTom3 software to the XDA with no problem. When i start up TT3 the software calls up the GPS part first and then starts the main TT3 prog. (as it did on my IPAQ). Although i haven't bought a suitable connecting cable yet for my receiver (the old receiver IPAQ plug does actually fit into the XDA!) when i start navigator up the XDA complains that there is a problem with COM1 not existing. After a couple of "OK" clicks it then boots up navigator and the maps etc seem to be as normal but the GPS says it is disabled.
Any ideas greatly apreciated
Doug
The iPAQ and XDA connectors although physically identical are not the same. The GPS disabled message is because it can't detect the GPS which given you don't have the correct lead is understandable.
As for the COM1 not exisiting error, do you have nything else which may be using COM1 such as an external or clip on keyboard driver?
To enable com 1, go to settings/connections and uncheck the "recieve incoming beams" also if you have an external keyboard driver that will also need disabling.
Now i'm impressed. Thanks to both of you for the replies. I unchecked the beam box and it goes direct to TT3. Brilliant.
(I think a donation may be in order soon) :wink:
Doug
considering getting tomtom5 for my mda compact.
anyone know whether its compatible, has anyone got it?
Should be. TomTom 3 and 4 worked fine.
By the way, Bakonl's release of TomTom 5 was just posted on alt.binaries.warez.pocketpc.gps, along with a few maps.
Benelux map only.. :x
TT5 does work
and not only benlux maps are posted. italy, france, germany, spain, uk are posted as well. rest will be posted as well i guess.
anyway, waiting for my legal TT5 to arrive (with the bt gps), woei =)
I can't get it working... I tried installing in the program files and in the storage card directories but it crashes at the end of the tutorial, just after that the "Welcome to TomTom Navigator" message appears in the map screen.
I can't see the map nor the GPS is able to connect (TomTom "3" Navigator Wireless).
I can't find any registry entry, I modified the currentmap.dat in order to point to /storage card/italia-map.
Anyone was able to reproduce my problem and to solve it?
Yeah, I noticed there are a few maps out. I'd like Scandinavia tho Seems like a buggy version too.. Crashes often.
Yeah... reeeeally buggy, I tried to check the post in the alt.warez.pocketpc.gps newsgroup for infos about bugs/problems etc. but I can't find it in my nssp server and using the web I'm not able to see the post (I can just see the header) so... I still can't use it :lol: ; maybe it could be a bad installer, I noticed that sometimes it won't install some cabs from the cd, or maybe it's just the italian map which is corrupt... who knows? 8)
I guess the release on alt.binaries is a preview or beta version.
The official release of Tomtom 5 will be end of June.
Im still waiting for Destinator PN on emule...
Where can i find the TomTom 5?
I have installed TomTom 5 to see if it works, I'm unable to connect my BlueTooth GPS (Holux GPSlim 236). The port does not show up on the device list under Buzz WM2005.
Does anybody know how to change this?
Ikkuh
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
JesperR said:
Where can i find the TomTom 5?
Click to expand...
Click to collapse
www.tomtom.com
Stefan
bruxelles5 said:
I have installed TomTom 5 , I'm able to connect my BlueTooth GPS (Holux GPSlim 236) on port 4
work OK for me !!!
Click to expand...
Click to collapse
I had the same problem.... go to the bluetooth com ports, change the GSM to use COM8.
Then start -> settings -> gps, on the first tab set com4 and on the second tab tom com8. The thrid tab should have the checkbox set.
Now reset your device.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Now exit tomtom and reset your device.
Start tomtom and wait a while (can take a few minutes for it to find the GPS).
This worked for me (you need the resets in order to detect the com ports!!)
Ikkuh
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
dickr43 said:
@Ikkuh,
How can I change the Com port settings on my MDA Compact? I can't seem to understand you're solution. I need Com 8 and TT5 only has 2,4,5 and 9.
Thanks in advance!
Click to expand...
Click to collapse
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port, and attach it to the hardware GPS. If you do this and reset the device, the virtual GPS will show up in TomTom (in my case it did ;-) )
Ikkuh
I must admit dickr43 has got a point. Even though you are trying to be helpful, Ikkuh, it's a bit hard to understand.
Start tomtom, goto your GSM setup, choose Other bluetooth, select COM4.
Click to expand...
Click to collapse
There IS no GSM setup in TT. Most likely you mean GPS?
There is a serial port multiplexer build in just for the GPS. It is under settings -> GPS, if you use this, you can create a virtual serial port
Click to expand...
Click to collapse
Doesn't exist either. Must be some third party app you have installed...
dickr43,
Try removing your GPS pairing from the Magician. Go select the 'Bluetooth Setting' icon under Settings/System and make sure both the serial ports are activated. Note which COM port is 'Outbound', then re-pair with your GPS device. Start TT and in the GPS settings panel, you should get things running by selecting the COM port that was marked for Outbound.
Unless you are running some third party software with virtual BT COM ports, that should get you up and running. If you are, try each COM port one by one. Don't hurry through the ports, but give it time to connect. 5-10 seconds at least. Also make absolutely sure your GPS is within range and has a satellite fix, or you are wasting your time.
I cant use tomtom 5 as a route map
I just want to use it sometimes without the gps module is it possible. Because with the older version it was possible to select a GPS simulator.
THX :lol:
The "unofficial" versions of TomTom5 doing the rounds seem to have been taken from beta builds. I installed without any problems, but noticed a number of bugs (not recognising GPS, the program freezing, picking up wild GPS info, settings not sticking)... sometimes you'd think it was working, and you'd think you'd got it stable, but then they'd fall down.
I've tried 3 different versions doing the rounds right now and none of them are stable. I'll wait a month or so for a more finished release is available.
i got my hands on TT5 aswell, the program looks realy nice and lot improvement to TT3, but as mentioned above, it's not very stable, spontain exiting of TT5 is not cool when youre in the middle of no where.
my gps was recognized directley,
i just went to BT settings and checked Com5 and a messege apeared that i must bond with a compatible device, so i bonded with my GPS reciever and in the TT wizard i could chose Com5 and it connected right away, much easyer than TT3
regards.
Hi,
I am considering getting TOMTOM5 for my T-Mobile MDA Compact and would like to use this in my car. Does anyone know or can provide screen shots of what the display looks like? Is it easily readable while driving?
Thanks
Msuk
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Had no problems pairing my BT Slim GPS with my Vario II, TomTom runs fine.
What GPS receiver you using ?
works fine on my xda trion as well.......im using tom tom 5.21 with BT-338 gps receiver.......im also using com port 0......you basically have to pair it and then add outgoing port as com port 0.....and during the installation on tom tom make sure you choose com port 0......that worked for me anyways....hope that helps.
Bluetooth GPS HTC TYTN
Thanks guys have re-installed tomtom and now it comes up with com prt 0.Probably didn't install correctly first time .Now up and running .Fantastic!!!!
I could cry
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
mobilecat said:
Hi everyone - I am having a similar problem
I have a new GPS receiver and have established a bluetooth partnership and done the outgoing port to com0 which is the default.
Tom Tom is installed and when I try and configure it I am not seeing all the options shown on the website. It just says no gps detected or something similar. I am sure its something simple.
Can anyone help please?
Click to expand...
Click to collapse
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
OUCH
dew.man said:
There's a program CreatePorts that is floating around (you'll have to do a search) that allows TomTom to see additional com ports in the Bluetooth GPS setup. I used this same program on my Samsung i730, and now on the 8525.
You just paid your GPS with the PPC, create the outbound port (in my case I used com 2), run CreatePorts, and then go in to TomTom GPS setup.
Once you get it set up, you don't have to run the app anymore, and TomTom works great
Click to expand...
Click to collapse
I tried running this but i can still only assign certain points from my bluetooth manager and dont have these displayed on the tomtom menu.
When you go into the GPS Status settings on Tomtom and tap configure, have you tried looking to see which com ports it lists and then going back to the bluetooth settings and doing trial and error to allocate any of those port numbers as an outgoing port for your GPS unit?
For my genuine Tomtom GPS unit, I did not even have to set up a port, I just had to pair the device but when I used a friends alternative brand of GPS unit for a short while, I was only able to get that one working under Com port 4. I can't quite remember but it may even have been a case that Com 4 only became visible in the Tomtom GPS configure menu after I had allocated it as an outgoing port for the GPS device (sorry, it is a while back so I can't quite remember the order in which I set it up)
Hope you get it sorted
arghh
I a so annoyed. I did this and had no luck. Later on I did something and got the option for port 2 and used it and it was great. I had to do a soft reset for something else and I cant do it again. tried everything.
MMMM
Happy yet frustrated
I have deleted create ports from my device as it only works once. I have reset my device. I reinstalled createports and extracted the file. I then saw port 2 straight away - the one that had been missing in tomtom.
The only problem is that if I do a soft reset I have to do that again!
It is very frustrating trying to get some of these things working. Have you thought about upgrading to Tomtom 6? you may find you have less problems getting the pairing and ports working right.
Failing that, I am sure you will be able to get it working again, just keep trying all the com ports one by one until you find one that appears in the Tomtom configuration. Like I said, on my XDA Vario II (Hermes) I managed to get it working on Com 4 and when I had an XDA Mini S (Wizard) I seem to remember that it was either Com 6 or Com 7 which worked on that one.
You might want to check the bluetooth settings for security and beam as well. Try turning security off (ie. passkey required off) and make sure the beam setting is ticked to receive all incoming beams.
I will keep my fingers crossed for you
download co-pilot for uk
Dashley said:
Got my htc tytn loaded totom 5 onto it and guess what bluetooth gps doesn't work with it! Cannot get correct comm port .According to HTC TomTom know about this. Just hoping somebody already has a fix for this?
Click to expand...
Click to collapse
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
download co-pilot softwear for UK.
Any one got the co-pilot softwear to insallate for MDA VARIO 2.
another thread
I have just seen another thread about XDA with a patch for this that seems to work. Can someone merge the threads?
Createports
Can anyone point me in the right direction to find this program. I think that it is hidden on the web somewhere near the holy grail.
Help with TT6 + TYTN + Royaltek 2110 please
I have a TYTN and a GPS Royaltek 2110. I have position com0 and other programs GPS work correctly. The problem is that the TT6 always shows he himself message “GPS nonfound”, although always I can say to him that this in the COM0 but does not find satellite.
That I can do? I put the TT5
somebody it has the CreatePorts program and it can put it?
Thanks
try this thread:-
http://forum.xda-developers.com/showthread.php?t=288865
Pairing TOMTOM 6 with Bluetooth GPS
For all of you that are having problems pairing your GPS Bluetooth receiver with your Hermes see the instruction set below:
#Hermes can not be in flight Mode#
1st: Run BTHTools1100.exe
--------------------------------------------------------------------------------------------------
2nd:
Pair them in Bluetooth Manager
Set:
Holux (outgoing port com4)
Incoming Port (com8)
no security
------------------------------------------------
3rd:
In settings >> Connections >> GPS
Programs set GPS program port to Com 8
Hardware set GPS hardware port to Com 4
baud rate 4800
If GPS program is not seen in settings\Connections
Use resco registry or other program and:
Go to Hkey_local_Machine\ControlPanel\GPS settings\ creat (make new) "Group" with Dword data =2
---------------------------------------------------------------------------------------------------
In TomTom chose:
Bluetooth GPS
Com4
should be working Now
Pairing TOMTOM 6 with Bluetooth GPS (easy) - Kaiser
First after reading the posts I thought I had to reinstall Tom Tom or install another software. Luckily, I paused and read the message when I was about to configure my other bluetooth receiver. It said, first you must establish your bluetooth connection. Well, I lied coz I did try to go on and couldnt find COM 0 or whatever you guys have said.
But that's what I did, eventually. Paired the device as BT GPS, check the serial connection (not sure if secure connection needs to be checked but I left it unchecked to find out later). After that go to com port tab, and click add new port ie selected COM0.
Then go back to TT6 (restarted in my case), and to other bluetooth gps receiver then found COM 0 in there. Voila!!
Chose COM0, but still got no gps device message. Waited for about 2 mins while reading further into the posts and now my TT6 is working.
You could call that strike of luck I dont really care but yeah.. saving some batt power on my kaiser for the bank holiday;s trip. Have a great one everyone!!
P/s: Mine is O2 stellar on Dutty's great work.
Com 4 is the only one that works with Schaps 3.54
Dear Htc fellows,
My bluetooth GPS is working strange on my Universal, but on iPaq with
WM2003 works as a charm. The BT GPS is new Solar GPS with new Mediatek
chipset.
It's not working with iGo 2006 and even not Tomtom 5 or Tomtom 6.
I can find the BT GPS in BT manager, I can pair it, but I dont know why,
it needs a pass key even if it shouldn't. Then when I explore it's
services, The popup come again asking me if I will allow external BT
device to connect to my Universal and it come asking passkey again (Why?).
I can't even enter an empty passkey (bt device doesen't require it). After that I have successfully paired the device. I can add it's serial port to enumerate on com ports 8 or 4.
When I start Tomtom, it doesent detect the device at all. If I use iGo, it detects, gets datas and disappear, it's allways appeared for 1 second and then 5 seconds not. No matter Which bitrate I set (device is written to be 9600) it needs to be in NMEA protocol, not SIRF.
When I use some freeware GPS programs, it seams to be working ok, it shows satelites and it's not disappearing.
What can I do with that???
I have some idea that it's probably about WM5 and it's security....
How can I setup com security in registry? can I set the port speads manually atd... I had performed a hard reset and it still don't work. Can ROM update or AKU update help me?
Does anyone have some idea what should I try now?
O2 XDA EXEC:
Rom: 1.30.107
Radio:1.09.00
P:42.42.P8
BT GPS: model: BT 2.5MR
made by f-tech.com.tw
Thanks;
Shef
Could you find a solution??
Hi,
I have the same problem exactly and could not find anything on the net. Did you solve your problem?
well ...
i know that there is a problem with GPS and WM5 and so there is this patch which i install every time i hard reset .....
the guys i bought MY GPS from gave me this ... and they are pretty knowledgable .....
it works well ....
try it !
tried
My OS version is WM2003 but tried anyway.. Did not work.. can there be version for WM2003??
did you ?
did you define an outgoing com port for the device (com 4 for example ?)
com port definition
well, igo finds the device an COM 6 actually, it connects too.. but stays connected just for a second, then again and again..
I installed GPSGate and created a virtual com port 7. I manually configured the GPS receiver connection to COM 7 on igo.. But all the same.. :
do you advice another way?
one other thing the device works with navigon 5.0 and tomtom 6.0 smoothly, no problem.. only igo..
well...
IGO is CRAP ... that is well known .... lots of bugs ...
i am sorry .. i do not know how to solve your problem...
but i suggest using destinator 6 ..... (that's what i use) ....
simple ... nice looking .... big buttons and able to navigate to your contacts directly (especially useful if you have Phone Edition)
oh ... and ... works great !
I got the Holux GPSlim 236 GPS. I can pair the GPS with Universial. But I cannot set the com port at all. A pop up window always say the com port (I tried everyone of the ports) is not available.
Any one got a solution, does the GPS bug fix help ? and what does it fix ?
Might seem a bit obvious, but have you tried the code "0000" when pairing your device?
Once paired...did you define an outgoing serial port on "Bluetooth Settings" menu on your WinCE?
I have a royaltek bluetooth GPS and it's been working well with TomTom[5|6]...I use '0000' as passkey (default on many 'non-interactive' devices), once paired I clicked on 'COM Ports' tab and defined a new outgoing port, the wizard should list the GPS as an available device to create a COM port so I used it and I got a 'com0'.
Once the outgoing port was created I had to tell TomTom to use the new 'com0' and worked like a charm
It's been working since TomTom 5.21 (previous versions didn't work).