Related
anyone got this working on the tytn
I use it with a Jabra BT250...
it used to work with my plantronics 320 on the wizard but wont work on the tytn is there any special settings you had to do
I also tried to make it works and it doesn't I assume that is due to the different headset plug.
Waiting for a version for TYTN
the prog will open a connection to the earpiece i can hear the static just wont forward any of the audio to it. works with the phone of course for making calls
I have the same problem with my Tytn (BTaudio seems to work because it stops the radio - I use it with a parrot car kit) but the audio still goes through the phone speaker...
did you find a solution?
gb
BTAudio On does not work, you have to turn it on via button press on the headset. BT Off works fine of course...
Rather annoying, but that's the way it is...
Sorry but I am afraid not to understand... the bt car kit is working properly and is paired to the qtek
could you please be more specific?
thks!
Sorry, you stepped into a rather cryptic response... I assumed you were talking about the file BTAudioOn.exe that worked on the 8125 but not the 8525/TYTN.
Search this forum for mono audio - there's a big thread. Also check the wiki.
attached. This cabs works great. To activate it, start playin music, then push and hold the button on your BT headset for about 1 second, it should beep and then music comes through. Only problem is you can't use MS VC through your headset, but it doesn't break VC.
BTaudio cab works
I have used the Gotland cab file and still had problems, until I began to think like a technician... Once I installed the cab file, I performed a soft reset and then repaired my Jabra JX10... It has been working fine ever since... I can hear music (either streaming or static) and voice... I have not tried tackling the voice commander problem though...
I have just upgraded the firmware on my headset using the software that is not posted on Jabra's site, but through a link in another post, I was able to do it... had to reinstall the Gotland cab again though.... May tackle Voice Commander later in the day... Who knows...
I'm using Bluemusic 2.0 and it worked with music to BT headset. Also using installed the BT VC fix cab in this forum at it worked fine with VC 1.6 - except incoming anouncements. ( Installation Hint: after installed both - you must delete existing device and then re-pairing the BT again).
I just made a thread, here http://forum.xda-developers.com/showthread.php?t=306363
Using the Voice Command over Bluetooth registry hack I am able to have the BT headset kick in and work with Voice Command perfectly well. I can even change the registry setting to have it run something else, like te Media Player, and hear music over my head set (It's a Jabra XJ10 btw). Problem is, the headset stays connected for only about 15 seconds, before switching off and the TyTN using it's main speaker again. Has anyone figured out how to keep the connection on by any chance?
It shows that playing music over a non BT Stereo headset is possible. But it stops automatically after 15 seconds as voicecommand restarts. I think there is some way to rework this so we can listen to music with the BT headset.
qing84 said:
It shows that playing music over a non BT Stereo headset is possible. But it stops automatically after 15 seconds as voicecommand restarts. I think there is some way to rework this so we can listen to music with the BT headset.
Click to expand...
Click to collapse
The 15 second thing applies even when te button is made to run media player, or some other software, not just voicecommand. I am hoping there is some registry fix that can be changed to fix this. Either that, or some hardware registry fix that would allow me to change the already-detected handsfree profile of my headset into a BT Stereo profile. If anyone has a BT stereo headset and access to registry settings for it, please post them here so I can try messing with it. Thanks.
I did see a program some where on here that allowed you to click a check box and it put all audio through the BT headset. Search around, I'll see if I can find it again.
Hi,
I been trying the BtAudioNav to redirect sound to my bluetooth hands-free but it doesn't work on my Trinity.
Anyone has try it with success?
Most mono-headsets do not support the A2DP profile.... so it is to be expected that this doesn't work for music and stuff...
However, i had it working once on my old Fujitsu Loox 600...can't remember how i did that though, but it has a different BT stack anyway...
Or do you just mean the phone-calls being redirected does not work ? Please try to be a bit more specific
Phone-calls works but for example redirect sound from GPS soft to headset not!!. With BtAudioNav should works but with my Trinity not.
Not all phones are capable of directing all audio to the mono bluetooth headset using the handsfree/headset audio gateway profile. Many of them are designed to ONLY stream voice calls. I'm not sure if this is due to the hardware or software (possibly a combination?), but some phones are capable of streaming/redirecting all audio entirely (as well as mic input) to the mono headset. I guess the Trinity doesn't. I've only heard of a few phones that actually work with that BT audio utility you're using, and they seem to be mostly older models, but that's just a guess. Anyway, perhaps there's a way to redirect all audio through the stereo bluetooth profile instead?
1. Copy the folder BTAudio and its contents to \Program Files
2. Using a registry editor amend the following entries from:
HKEY_LOCAL_MACHINE\SOFTWARE\OEM\VoiceCommand
Path = \Program Files\BTAudio\BTAudioOn.Exe
VoiceCmdDuration = 86400 (DEC) = 24 hours
3. Softreset
What does the above tool do exactly?
Tiemen said:
What does the above tool do exactly?
Click to expand...
Click to collapse
Yeah...i'm very curious to what this does too...
Could this by any chance connect a Stereo BT headset in Audiomode by just clicking the .exe ? (ie not having to go into BT settings in the comm manager screen ?)
Moaske said:
Yeah...i'm very curious to what this does too...
Could this by any chance connect a Stereo BT headset in Audiomode by just clicking the .exe ? (ie not having to go into BT settings in the comm manager screen ?)
Click to expand...
Click to collapse
Yes, can you please be more specific as to how this works? Does it interfere with voice dialing or making/receiving calls?
I have an Axim X50v which works just great with Skype and my mono Flamingo BT headset. Now I have an HTC P3600 and Skype won't work through the headset.
Bloody technology seems to go backwards :-(
Thanks.
qyach said:
1. Copy the folder BTAudio and its contents to \Program Files
2. Using a registry editor amend the following entries from:
HKEY_LOCAL_MACHINE\SOFTWARE\OEM\VoiceCommand
Path = \Program Files\BTAudio\BTAudioOn.Exe
VoiceCmdDuration = 86400 (DEC) = 24 hours
3. Softreset
Click to expand...
Click to collapse
After editing, VoiceCommand function is LOST .
All sounds will be re-directed to the blutetooth headset when you press the button(voice dial) on the headset.
Guys, please DO read my past articles and/or use the forum search engine to look for them. At http://forum.xda-developers.com/showthread.php?t=281977 , I've explained everything you need to know.
Did anyone get BTaudio working on their Trinity?
BtAudioToggle opens a link with my mono headset ( I hear hissing in ear piece) but media still plays through Trinity speaker.
I read the Hermes forum about a different reg hack. http://forum.xda-developers.com/showthread.php?t=278778
Whats working for people?
Perfect audio re-direction with Jasjar & Jabra BT250v
that was very neat & BRILLIANT !!!
got my Jabra BT250v without knowing these issues. on discovering that my jasjar was not capable of audio re-direction to Jabra.....I was shattered. ROM upgrades r scary to say the least.
after a day of frantic search & many failed softwares, this one did the trick. 'qyach'.....many thanks for this.
now my Jasjar & Jabra work perfectly with TCPMP & Skype. Voice command continues to work from the Jasjar mic.
I couldn't ask for more.
THANK U ONCE AGAIN !!!
Tried VJVolubilis, Bluemusic and BTAudio (with both of the 2 registry hacks referred to in this thread). None of them worked on my Trinity. Would very much appreciate someone shed more light on this issue.
qyach said:
After editing, VoiceCommand function is LOST .
All sounds will be re-directed to the blutetooth headset when you press the button(voice dial) on the headset.
Click to expand...
Click to collapse
Doesn´t work on my Trinity
Edit: don´t know why but now it works. Only that I have to press the voice dial button twice (?)
Hi,
I got the Motorola T305 to connect to my TyTN and the audio gateway routed to the T305. Everything sounds great but I get this annoying beep once every 5 seconds. Does anybody know how to get rid of it?
Thanks,
Sean
JUST SORTED IT on my TRINITY all workin fine
Only problem is, as the article suggest it disables the voice commands!! I can live with this as I only want to stean the TOMTOM voice when using the satnav while walking or on my bike.
What I had in mind was a a couple of icons, one to make the registry changes for the BT Audio streaming and the other icon to toggle back (ie change the registry back to voice comand via the BT headset). As far as I can see (once BTaudioOn.exe is copied to my Trinity) the only difference between turning my Jabra BT250v into an audio streaming headset and a phone headset are the two registry changes; and then change them back to give me a Phone headset again.
Can anyone tell me if this is possible to use a .REG file?
Can it be written on a PC and then copied to the Trinity so that it runs?
Will reg files run the same on a PDA and they do on a PC?
Thanks in advance
New app?
Can anyone make an app in which you can configure which feature you want?
1) Change to Voice Dail
2) Change to Voice Command
3) Change to a redirection program like BTAudio.
and got to set the delaytime too
Destination Gotland Bluetooth Mono Sound.cab
I installed this, no registry changes, etc. and it works great. you toggle between unit speaker and the headset by hitting the button on the BT headset. It is great for Skype.
The Cab is in the Zip. I think I picked it up off the tutorial here:
http://forum.xda-developers.com/showthread.php?t=281977
Battery Problem
OK, the solution I posted does work well. However it just killed my battery life. I think that whenever the BT is paired, even in the regular mode (not streaming to the mono BT) it uses the full amount of battery as if it was streaming to it. I think the battery life was even reduced without a paired headset as long as BT was not disabled.
I guess I am still looking for a better solution too.
qyach said:
After editing, VoiceCommand function is LOST .
All sounds will be re-directed to the blutetooth headset when you press the button(voice dial) on the headset.
Click to expand...
Click to collapse
THANK YOU !!!! works purrrrrrrrrrfect !!
Hello Everyone,
I've got a USCC Vogue, which is running a wm 6.1 rom I cooked using PPCKitchen's Rom Kitchen. The strange thing is, I paired my Jabra BT8010 headset to the vogue, and it works great, until I turn it off. To get it to work properly again, I have to delete the device and repair, OR I have to put the headset in Stereo A2DP? mode, then press the play/pause button, after which I can switch back to phone mode with the headset with very few issues (ie, only the known MSVC1.6 problems.) I've tried using acbToggle to switch the audio gateway over to bluetooth, but the volume is low. I've also tried plugging in my headphones and then toggling, and that helps the low volume issue some, but not as much as re-pairing or doing the a2dp trick. Also, shouldn't the vogue automatically connect to my headset upon turning the headset on? Because I have yet for it to do so. Also, if I go into the Connections/Bluetooth menu item, I see the headset, and if I bring the menu up for the headset and select either Set as Headset or Set as Wireless Stereo, nothing happens. Is there some other way to set my headset to automatically connect as Wireless Stereo? (this setup gives me the best performance and volume)
Thanks in advance for any help/information anyone can give me.
Jamie
hudson_macbeth said:
Hello Everyone,
I've got a USCC Vogue, which is running a wm 6.1 rom I cooked using PPCKitchen's Rom Kitchen. The strange thing is, I paired my Jabra BT8010 headset to the vogue, and it works great, until I turn it off. To get it to work properly again, I have to delete the device and repair, OR I have to put the headset in Stereo A2DP? mode, then press the play/pause button, after which I can switch back to phone mode with the headset with very few issues (ie, only the known MSVC1.6 problems.) I've tried using acbToggle to switch the audio gateway over to bluetooth, but the volume is low. I've also tried plugging in my headphones and then toggling, and that helps the low volume issue some, but not as much as re-pairing or doing the a2dp trick. Also, shouldn't the vogue automatically connect to my headset upon turning the headset on? Because I have yet for it to do so. Also, if I go into the Connections/Bluetooth menu item, I see the headset, and if I bring the menu up for the headset and select either Set as Headset or Set as Wireless Stereo, nothing happens. Is there some other way to set my headset to automatically connect as Wireless Stereo? (this setup gives me the best performance and volume)
Thanks in advance for any help/information anyone can give me.
Jamie
Click to expand...
Click to collapse
The real questions is did it work before you flashed your custom creation? Is it possible that there is an issue with your ROM?
I have been reading many threads on getting the "stereo audio" connection to auto connect fot BT Stereo headsets. It seems that when you pair it the first time, both "Hands Free" and "Stereo Audio" are working. When you disconect your headset and reconnect it again, only "Hands Free" connects.
I have tried A2DP toggle and A2DPSwitch, but they dont seem to work on the HD2. A2DP toggle did work when I had my old Samsung Omnia i900, so I can assume that its something to do with the HTC Phone Bluetooth stack
Each time I want to use the BT Stereo headset, I need to go to settings/menu/all settings/Bluetooth/590Plantronics and expand + and select "Stereo Audio". They then connect.
What I would like to do is until there is a fix for this, to reduce the number of taps, is create a shortcut to the Bluetooth Control Panel that shows the 590Plantronics device.
Is this possible?
Thanks Chris
Just make a shortcut to Windows\BTManager.exe and add it as a quicklink.
hi,
i have a jabra 3030 and a motorola s705 and both are reconnecting (handsfree and stereo audio) properly, when i turn them of and on again. when i go out of range (eg. forgot the mobile in teh car), when i come back the handsfree connects direct, and the setereo audio after i press the play button once. maybe this works for you also.
regards mad
I installed AutoA2DP on my phone and ever since, whenever I turn on my headset, it always connects as both stereo bluetooth and headset. I haven't tried it on an HD2 but you should definitely try it out.
I found the .cab of AutoA2DP awhile ago but forgot where I found the download link. In any case, I have attached it for your convenience.
D.W
Hi kilrah, thanks for your advice! That cuts out a few blinkin clix now and will do as a work around till this fiasco is solved, lol
I also noticed something very bizzare, and it is confirming my suspicions that HTC is in cahootz with MS or Widcomm or both, lol.
I tried using auto a2dp as suggested by GurWu, leaving the a2dp.ini file as wmplayer.exe. I then deleted the Plantronics from the system, re-paired them and what should spring to life after turning on the cans? You guessed it..WMP all paired up with HF and Stereo Audio. Turned off the headsets, turned them back on again and sure enough, WMP launches and plays thru the headsets.
All good, except I wont use WMP as it STILL doesnt have an EQ (Not getting in to why one needs an EQ or not here, lol)
No problems, I thought, Ill just set the a2dp.ini to pocketplayer.exe (my preferred player) turned on the headsets and.......nothing....no pocket player came to life.
Doing a manual launch of PP revealed that the headsets were only paired as HF, so back to my original problem.
Renamed a2dp.ini back to wmplayer.exe and it all works as it should....mmmmmm...does this wreak of a MS/HTC/Widcomm ploy? LoL
PS @ mad: When you said press the play button, were you referring to the play button on the software of your chosen media player or a hardware button as I dont have a play button on my HD2
PPS: Got a reply bacl from a2dp toggle author, says that it only supports M$ BT stack :-(
Cheers Chris