Related
Hi guys,
ive had my exec for about 2 weeks now. In the last week it has started to randomly loose network signal. It keeps searching till you either soft reset it or turn flight mode on and off. It will find a signal in about 10 seconds after that.
Is this there a 'dont keep loosing signal' setting that im missing?!
Mine does the same thing - annoying as hell! Not worked it out yet.
Are you talking about telephone or GPRS signal ( U or G )
Phone signal
everything! it looses all signal.
I called o2 and they want me to go into an 02 shop for them to have a look at it before they give me a replacement
The are all 'handset trained' apparently.
I also called o2 a week ago stating the same problem, They gave me a refferance number and said they will look into it, But of corse 1 week later they have not called me, So this afternoon i will find the referance number and give them a call.
I will post ther Bollox answer on here tonight
John
Same problem here with a MDA Pro. I ahve noticed that this happens when I am roaming in Germany as well. Very anoying. That and the thing freezing in a call and needing a re-set. This is my second one as the first one the screen portion became loose, happened on the one before as well.
I have the same problem althoughmine will refind the signal after about a minute. It seems to disappear whenever I ask thephoneto do something new (open a program etc).
I finally persauded T-Mobile to exchange mine so I'm getting a new one delivered tomorrow.
I'll let you know if that fixes it!
Andy
My XDA2 used to lose its ability to communicate if I was out of a signal area for more than 15 minutes, but I haven't had it happen yet with the Exec. A soft reset or Flight Mode on/off cycle would fix it.
It is frustrating but didn't happen often.
Well i phoned o2 and they said there was still no answer and that no one else had complainded about this, So i told them of this forum......
As per the last post i have also had this on a 2 and 2i, and i gree if its out of servie for a few mins its seems to give up looking for service until you reset.
mine has done it overnight befor, i looked befor going to bed and it had just the 3 dots flashing where the aerial should be. the next morning it was still the same, quick soft rest and into full service, thats when i first rang o2
John
I've had this on all my XDAs in the past, and seems to continue with the Exec.
Very annoying, but not sure what can be done about it.
Ant
guys,
wait for a rom upgrade from o2, ( with new radio rom)
that should solve the problem.
happens with xda, xda2, skipped xda2-i and xda2-s,
and now it's back.. :roll:
Hi Guys, I have been having this problem for weeks with my MDA Pro. I convinced myself it wasn't the phone and that it was T-Mobiles Network. In desperation last night I spoke to T-Mobile about the problem. They told me it was a faulty phone and that I would have to contact the supplier of the phone and ask them to replace it. I tried to explain others had the problem and that I wasn't happy to have to send my phone off and wait for a replacement. But no avail. So I sat down at home and looked at the settings. I think I might of cured it! Maybe it is a fluke but by clicking the signal meter and going to settings, then changing network selection to manual it has stopped hunting when it loses signal and quickly re-picks it up. HNope this helps others.
Giles.
abarthsmart said:
changing network selection to manual it has stopped hunting when it loses signal and quickly re-picks it up. HNope this helps others.
Giles.
Click to expand...
Click to collapse
Defenitely...that did it.
I had the same in Holland with KPN: while switched to manual no more problems.
In Romania however, where I also have UMTS, I had to switch it back (or it switched itselve back, after changing SIM card, I don't remember) to AUTO.
There it switches from GPRS to UMTS if UMTS signal is OK.
Huib
Ok, i have the same problem. Have GPRS Always on set in registry and 10 minutes ago, my MDA Pro lost GPRS connection. It trys to reconnect all the time. But no Connection can be build up. After Flight Mode and back, i get a connection immediately. But on start of MSN Messenger, it loses the connection again and does the same loop like before. Only a softreset brings my connection back to live.
Looks like a ROM issue. Maybe GSM or CE.
I am delighted to say that my replacement MDA Pro seems much more stable in the signal department. Although I still loose signal ocaasionally, I no beleive that is due to poor signal area and not the phone...
If you phone isloosing and reconnecting all the time then like mine it is probably faulty! Hopefully the ROM upgrades will sort out the last few issues I'm having!!
I love this phone!!
Same problem with JASJAR
People still have this problem? i'm using radio 1.03.01. When i used the original firmware, the phone part would lock up (Would get the busy - wait 15 seconds and try again, but it would never clear - had to soft reset)
With the 1.03.01 radio, i still get disconnected, but it'll find the signal again after a few retries - which is very bad! I rely on the phone at work, and people can't get through when it's disconnected. I have full signal strength (4 bars) so it's a software/hardware problem.
It looks like maybe it happens more frequently when charging or activesync'ing, than when it's disconnected from usb.
Can anyone confirm having the same problem, and it getting better or FIXED with the new radio firmware? If not, i'm going to have to return it.
Michael
I am using radio version 1.04.02 on the O2 exec, although i use a Vodafone SIM (supplied by work!). Mine suffers from the same problem, mainly at home, which is a very odd signal area for Vodafone. I can go from no signal to full signal to none again, and yes, sometimes it drops completely and needs a soft reset - bingo! full signal again.
Switching the network type from auto to GSM does seem to make the unit a little happier, but i need to use WCDMA when possible, so i leave mine on auto and live with the dropouts!
Lets hope the next rom fixes the problem.
Cheers
Paul
I have the same problem with my XDA and O2. a soft reset nor a full reset have been able to fix the problem. :roll: is the new rom version available as yet?
Quite often these days I am getting the issue mentioned above. Even soft resets do not seem to help. Until I reset a few more times.
What might be the cause of this? Thanks.
Hope someone might be able to assist on this. Thanks.
I'm also getting this message nearly every time I try to make a call. The phone then looks like it resets the connection with the cell tower and it successfully completes the call on the second try. Then the next time I try to call someone else it fails again. I came to this forum to see if anyone else has experienced the same problem.
Hey joej, I found out what might be causing the problem: make sure that your ActiveSync is closed before you try making a call. That fixed the problem for me.
Also, here's a quote from an email from one of my coworkers:
"Your Tytn was probably trying to dial a data connection at the same time that you were trying to dial voice and so it has to cancel the data request before you can dial out. There is a registry tweak you can do to the Tytn to keep the data connection always active when the phone is not in use and this may make it less frequent that you would have a problem
Activesync is supposed to stop when your data connection is unavailable. If you are making or receiving a call on the TyTN (or any GSM phone) your data connection will not be available and therefore not run. Do you have a lot of 3rd party apps running at startup as well? I have rarely had a problem with my Tytn and never during a call unless my battery dies on my BT headset mid call and then the device may get confused."
Hope this helps!
BlindDriver said:
Hey joej, I found out what might be causing the problem: make sure that your ActiveSync is closed before you try making a call. That fixed the problem for me.
Also, here's a quote from an email from one of my coworkers:
"Your Tytn was probably trying to dial a data connection at the same time that you were trying to dial voice and so it has to cancel the data request before you can dial out. There is a registry tweak you can do to the Tytn to keep the data connection always active when the phone is not in use and this may make it less frequent that you would have a problem
Activesync is supposed to stop when your data connection is unavailable. If you are making or receiving a call on the TyTN (or any GSM phone) your data connection will not be available and therefore not run. Do you have a lot of 3rd party apps running at startup as well? I have rarely had a problem with my Tytn and never during a call unless my battery dies on my BT headset mid call and then the device may get confused."
Hope this helps!
Click to expand...
Click to collapse
thanks for the update, i however am experiencing this issue once in a while and it is not with the activesync running nor a data connection going on. ugh..... guess mine is odd
Me too
Thank so much for the post count me in there too. I am southern central PA and just last week this started happening to me too. I have an 8525.
I have no acrive data connection nor any apps running that force a data connection. Every morning I have been resetting the phone 5-6 times before the freezing stops and it works. So annoying.
I am suspecting it is a network issue with cingular and them upgrading to 3g in my area. I suspect it as I had to travel north this week and discovered 3g coverage in Harrisburg so I am betting that is it.
I feel your pain and I have no fool proof thing to do on the phone to fix it. But man the phone on the 3g is fantastic.
duman95 said:
Thank so much for the post count me in there too. I am southern central PA and just last week this started happening to me too. I have an 8525.
I have no acrive data connection nor any apps running that force a data connection. Every morning I have been resetting the phone 5-6 times before the freezing stops and it works. So annoying.
I am suspecting it is a network issue with cingular and them upgrading to 3g in my area. I suspect it as I had to travel north this week and discovered 3g coverage in Harrisburg so I am betting that is it.
I feel your pain and I have no fool proof thing to do on the phone to fix it. But man the phone on the 3g is fantastic.
Click to expand...
Click to collapse
yup, everything rocks in it except the phone functionality really needs to be improved to be more usable.
do you know how i can use the phonepad to do t9 for replying SMS ? right now i am finding it hard to do so as i need to use the normal input methods which is not as easy as a normal cellphone
omg I'm from Singapore using Starhub think I'm having the same problem too. Dopod 838 pro.
A soft reset works for me, but very frustrating coz you dunno whether you are missing calls - the screen shows mobile is up with signal and all but people can't call in.
Just started happening to me past few days but then again I just took over the phone from a friend who bought it 3 months ago (latest batch)
So frustrating. ... seems related to the activesync.. but then again still happens when activesync's not involved.
duman95 said:
Thank so much for the post count me in there too. I am southern central PA and just last week this started happening to me too. I have an 8525.
I have no acrive data connection nor any apps running that force a data connection. Every morning I have been resetting the phone 5-6 times before the freezing stops and it works. So annoying.
I am suspecting it is a network issue with cingular and them upgrading to 3g in my area. I suspect it as I had to travel north this week and discovered 3g coverage in Harrisburg so I am betting that is it.
I feel your pain and I have no fool proof thing to do on the phone to fix it. But man the phone on the 3g is fantastic.
Click to expand...
Click to collapse
Same here anytime Cingy plays with towers, have you ever got a message stating the call can not be completed at this time? Been getting that one lately as well.
I think that it could be an issue with the phone heightened by the nature of the cell network.
I am wondering if the phone has issues handing off between cell towers as I have the band tab active and there are freq choices so I wonder if the phone even on gsm has some issues dealing with hand offs.
I locked it on gsm and still had issues with the phone. I locked it on 850 and still had phone issues. Put it in auto for the freq and still had issues.
On the U network on Cingular since its the only one the phone is excellent. Data and voice work great. So it will get better in the US for us on Cingular. But man its going to be really annoying during the roll out.
I'm on T-Mobile and I'm seeing this problem as well. (It didn't go away after closing ActiveSync like I said it did earlier.) The weird thing is that this wasn't a problem until about a week or two ago; now all of the sudden it's happening constantly.
Also, I just installed the newest HTC ROM (1.35.255.2) yesterday and now my phone has started to drop calls. I've never had a problem with dropped calls in the 2.5 years I've lived in this apartment.
Ain't technology grand?
Well things have not improved for me. Today after 8 resets the phone finally settled down and did not freeze and was able to get on the network. It has been terrible for me the last 2 weeks...
I removed the eten dialer skin I was using. I wanted to make sure it was not due to replacing the Cingular phone skin.
We shall see tomorrow if the phone is able to work without multiple resets..
If not it is off to a hard reset and re-load to see if that improves it any...
I have taken the plunge and did a hard reset plus reinstall of everything. I had the same apps installed again and the problem seems to be gone now. *touch wood* hopefully this doesn't come again... a restore takes too long. I have also installed Sprite and did a full backup of the phone including the memory card just to be safe.
This problem started for me this morning. (NYC/NJ Area - USA). I did a hard reset (actually, two) this morning, and it didn't fix it, even when the phone first finished the initial load (in a virgin state). Then, around 11:00am, it began to work again. Now, it's about 6:30pm, and I need the phone to call home to tell them I'm gonna be late, and it's out again. Seems like it's something not to do with the phone, but with the network (I hope). It won't connect in GSM, UMTS, or AUTO modes, FWIW.
Oh well, sure hope it doesn't takle two weeks to "go away".
returned
Well I returned mine. Did the warrenty exchange. So far so good. No freezing and the phone seems to hold onto the network ok now.
I truly believe mine was defective. As the phone would show searching and not connect to the network.
I think that not being able to make a data connection is a network issue as it clears up in a few days.
pvs said:
This problem started for me this morning. (NYC/NJ Area - USA). I did a hard reset (actually, two) this morning, and it didn't fix it, even when the phone first finished the initial load (in a virgin state). Then, around 11:00am, it began to work again. Now, it's about 6:30pm, and I need the phone to call home to tell them I'm gonna be late, and it's out again. Seems like it's something not to do with the phone, but with the network (I hope). It won't connect in GSM, UMTS, or AUTO modes, FWIW.
Oh well, sure hope it doesn't takle two weeks to "go away".
Click to expand...
Click to collapse
also in the same area, experiencing similar problems within certain specific locations. Noteably these are locations that I get SPOTTY UMTS service, so I assume a tower upgrade is in progress or something that is causing this. Where I have full umts service, the problem does not occur.
at times i have signal, but calls don't come through (rings to calling party, but goes to voicemail before my device rings).
This is something related to 3G because when the sim is put in a blackberry 8700c, everything works A-OK.
Glad to know i am not alone in this
I have similar problems. Especially in the university of Hannover. There is UMTS. Since a few days Data Connections via Active Sync don't work.
Before I had problems with calls. For example freezing during call.
And of course in the university and on other places I have often to do calls twice.
I called O2 for that problem. They are upgrading the cell around the university to HSDPA.
Hi to all !
I had the same problems, then i removed the microSD card and the problem was gone. Now i am testing the phone without miroSD card. I forgot to say that i had the problems with boot too(No GSM) and now it boot perfectly.
Best regards
O2 XDA Trion (dopod rom)
I finally had to return the phone under warrenty. It degraded to no gsm all the time fresh from a hard reset with no mem card. The new device has been flawless radio wise for a week now.
Problems with XDA Trion SOLVED !!!
Hi again !
The microSD card was NOT the problem ! I tested the phone without SD card but that was not the problem. Then i go to my provider and change the SIM card with new one (the old one was very old so i buy new one) and wauuu it works. The XDA TRION needs the sim card with UMTS suport then it will work fine. So far NO freezing at all. I will let you know in a few days if something strange will hapen.
Best regards
Hi, to all with the problem “The operation failed” when trying to make a call:
Try to switch off bluetooth (specially if you are in UMTS (CMDA) network) and then try to make a phonecall again.
For me this helped to solve it.
First I also thought that it’s only a Provider network problem (I have 2 different providers, with one it works, with the other I have the “operation failed” problems).
So it is 100% a phone software problem. (Shame to HTC)
Give feedback if it helped you too.
Recently my Vario II intermittenly loses network signals, it says No Network and I have to toggle phone off/on to make it search for signal again. This only happens when I'm at home (Charlton SE7 area).
Rom 1.21.110.3 (19/06/06)
Radio 1.05.05.00
Does anyone have the same problem?
toucam said:
Recently my Vario II intermittenly loses network signals, it says No Network and I have to toggle phone off/on to make it search for signal again. This only happens when I'm at home (Charlton SE7 area).
Rom 1.21.110.3 (19/06/06)
Radio 1.05.05.00
Does anyone have the same problem?
Click to expand...
Click to collapse
Flash HardSPL first, then upgrade your radio.
Ive linked to my guides incase your unfamiliar with the process.
The newer radio should possibly increase your GSM efficiency. Are you in a decent area for reception?
mrvanx said:
Flash HardSPL first, then upgrade your radio.
Ive linked to my guides incase your unfamiliar with the process.
The newer radio should possibly increase your GSM efficiency. Are you in a decent area for reception?
Click to expand...
Click to collapse
Hi, many thanks for your detailed guides. I've upgraded Radio to 1.38.00.10 but the problem still persists. I'm in a very good coverage area, always get full bars 3G when it works. Soft-reset my phone and now it's searching in vain for network signal, I'm confused
What operator are you with ? Maybe the cell where you live is getting overloaded. We had a problem similiar to this last month when our local base station had a problem. Our work-around was to disable 3G but not using a Hermes . Apparently the handset tries to register using the 'best' data-bearer its configured for. So disabling 3G made it register with GPRS which worked fine. They then fixed the base station and we were able to re-enable 3G. I would
guess Charlton would have a lot of subscribers per cell. You would expect the coverage to be better in a built-up areas but who knows. Maybe an enquiry/ complaint to the operator would at least tell you if they know of a problem and if its temporary or longer term
Cheers for that. I'm with T-Mobile. What's bugging me is that this signal disappearance only happens sometimes. It's not that I don't have 3G (or signal for that matter) at all, I still get full 3G signals fine most of the time. But you probably were right, looks like it's a fault from the operator's cell in the area, I will give them a call next week to see if there's an explanation.
I've noticed this problem when I'm in the south London area (very general I know). People have got around the issue temporarily by forcing the phone to GPRS only
More problems! After upgrading to 1.38 and trying all sort of "good" radios like 1.17, 1.27, 1.34 I can't make/receive calls unless GSM is forced. There must be something wrong within my immediate area because with the same radios everything works flawless just 10 mins down the road. I just called TMob and there's no technical fault or anything from their side. I will just have to put up without 3G until the problem fixes itself
There are lots of people complaining about 3g on T mobile in UK. They seem to have serious issues with Hermes devices and the dropdown to GSM.
I had a problem six months ago with my hermes on orange at home in SW London. For a few weeks it was mucking about - I rang O who advised me that they were experiencing some local issues but would fix them within days. I switched to GSM for a few days. When I switched back its worked fine for last five months.
3G gone mad!
the same thing was happening to me. Full 3G reception in Leicester, tried to connect to get my e-mails and then the signal totally goes. The same thing happens when I make calls as well. Switched to GSM and everything worked. Now in York and everything is working on 3G.
Network is T-Mobile.
This sounds similar to the issues I am having.
Do you get the phone hanging as it attempts to start a call and then after a while a message stating that it was unable to connect?....sometimes resulting in a soft reset to bring the device back online? In my case toggling bluetooth will reset the connection.
I am with T-Mobile in Glasgow but get the same issues during the day in Edinburgh
No 3G
aidanbree said:
This sounds similar to the issues I am having.
Do you get the phone hanging as it attempts to start a call and then after a while a message stating that it was unable to connect?....sometimes resulting in a soft reset to bring the device back online? In my case toggling bluetooth will reset the connection.
I am with T-Mobile in Glasgow but get the same issues during the day in Edinburgh
Click to expand...
Click to collapse
No mine doesn't say anything, it sounds "ding ding" after a few secs like when you press the hang up button. I can use the Internet but anything to do with calls is just impossible. I've switch to GSM now and everything's back to normal. A bit annoying can't use 3G at home.
Well this was bugging me for months so i decided to start an own thread. I live in Germany, on the border to Switzerland and France, so my Wizard often decides to change to the stronger signal from the other countries. Now, you know roaming is pretty much expensive, so this is me freakin'out.
I've tried manuel selection and setting the preferred networks for hundreds of times, but its still roaming - even now that i've updatet to WM6.
Is there any workaround or software for this? I mean i've started to use my old cellular phone because of that!
no one experienced this problem so far? common guys there must be a solution.
Hi all,
I flashed my phone, and thought I’d go with Darky's Raw Steel Edition (4.1), which is awesome btw. I installed it correctly, installing I9000XWJM8 first (the MODEM and PDA, not CSC as none seemed to come in the package).
Everything was working smoothly until I realise 3G/Data Network is no longer working (it did previously). Not only that but it seems it won’t connect to my service provider (Three) at all (emergency calls only), and I’ve also now noticed GPS doesn’t seem to work at all, I can’t even get into GPS test mode. Wireless does however work though it being off, or on, has no impact.
I’ve tried:
Flashing different firmware - Stock JM8 and Doc Froyo’s latest JPO.
Hard Reset
Deleting and re-entering APN settings, though they were correct and already on the phone anyway.
Testing my SIM on another phone – signal is strong, inc. 3G on that.
I’m really at a loss here. Any ideas anyone?
Thanks
UPDATE: So, I won't bump this myself, but incase anyone finds this thread in the future: the gprs, gps, 3g, etc all work - just not in my house, on the SGS, anymore. I have no idea why - my other phone, it's fine.. and it used to be fine with this phone too. I'll update again if I figure it out.
the other phone works fine with the same sim you are using in the SGS?
Yep, the same SIM works in my old Nokia 6600 fold, people in my house also with Three are getting solid reception right now. 4-5 bars with 3g established.
It worked beautifully all the way home from work on the bus, just not in/around my house.
It's as if the local cell towers near my house have blocked my SGS specifically (can't receive calls or texts either). I did turn the wireless on and off in short succession (which would cause the gprs/3g to try to re-establish each time).. maybe I flooded them and they blocked my IMEI? Or is that just a ridiculous idea?
The real odd thing is GPS not working either (again, just around my house/street); surely it doesn't need a cell site for that?
It does seem as if I can't download apps from The Market anymore either, and have tried various cache clearing solutions to fix it (problem occurred roughly when I noticed my reception was nill).
You might have a problem with the band selection thing of your phone.. have you tried downloading/speed test when you /do/ get a connection? If it seems capped at 40kbps, you might have the same problem I experienced before, of being stuck on 2g. (Despite settings saying otherwise).
I fixed it by doing the solution to having a missing 850 band, the thread of which is found somewhere in this forum.
Thanks. That sort of worked earlier.
It made a slow data connection, and some texts came through.
I then went out to a location a few miles away, had a look and it was still on a slow connection type for a few mins, then all of a sudden it went to HSPDA (with the occasional 3G flicker) and was blistering fast.
Now that I'm back home, I've lost all reception again and can't make/take calls
[EDIT] Clicking around my phone in the hopes of finding something: checked product code in my nv_data.bin file with SGS Toolbox, and it's showing I9000HKDKOR; whilst the backup is showing I9000HKDH3G - could I be on to something? I backed up my efs folder after rooting before doing anything else - so, going to try restoring that.
I have a hunch based on a 2 year old post (http://forum.xda-developers.com/showthread.php?t=445913).
From what I understand, Three UK piggy back on Orange's network when Three's 3G cell towers are out of reach. Orange don't provide Three users with the full service though, just 2G and I'm guessing they prioritise Orange customer traffic.
I think when I flashed my phone, I removed code commanding the phone to prefer Three cell towers. Without that code, the phone simply goes to the strongest/first signal it detects. I'm guessing in the area near where I live, it's Orange (or maybe any old network which is why I'm often getting Emergency Calls only).
This is all guesswork. I'm hopeful, seeing as if I quickly switch the SIM to my two+ year old phone, then I quickly get 5 bars and 3G.. unless the SGS's signal issues really are *that* bad.
http://forum.xda-developers.com/showthread.php?t=831022
Try see if you have the symptom of a missing band?
Hi Nwsk, I tried that before and assumed it didn't work, but actually the change isn't sticking. Which seems to be the case for a couple of others! Thanks for pointing me back to it!
[Edit]
Ohhhh dear. Now I have another theory (I really hope I'm wrong).
I've just read on a thread that some phones don't have the 850 Band, it's down to a lack of hardware support. I'd wager every Three UK branded phone sold will have the correct hardware as stock. I sent my phone back to Samsung for repair, they said they replaced the motherboard.. inference: they replaced it with one without the WCDMA 850 support.
Hmm, I'm definitely no authority on this, since I'm just guessing.. but I figure if that if was a true hardware defect, you wouldn't even be able to get it temporarily?
Are you using any 'battery-saving' type apps? Something might be messing up and keep reverting the settings. I had this occur to me a second time when I was trying out the superpower app here, I think it conflicted with another app I was using, and it borked out my network connectivity. Somehow fixed that after a few reboots, and lots of messing around in the phone debug menu with the 3g/2g thing, it suddenly worked again.
I've not seen it manage to get onto 850MHz WCDMA in my house for a while, not since the mobo got replaced (I should qualify that with a statement on my bad memory ). It will occasionally latch onto something if I walk around the house, giving me a slow data connection with the G symbol showing - it will drop pretty quickly.
Messing around while I write this, I've just realised if I set my phone to GSM(2G) with roaming [Three UK phones need this on so they can connect to Orange towers], then it does establish a data connection at 1800mhz. If I force WCDMA only, I get NOTHING. Setting both/auto leads to it being dodgy/instable, as I've discribed above.
My Nokia 6600 supports 850mhz UMTS, which would explain why it's working well inside my house.
I don't think it's an app. I've flashed a few different firmwares in an effort to get this fixed, it's currently on official Froyo JPO (not even rooted!) with Multi-CSC and a few completely harmless apps. I'd try the stock Three firmware if it was available somewhere.
I'm hoping it's software like you suggest! I will tinker away for now!
Thanks for all the help, at least now I'm fairly sure I'm on the right track!