Hello everybody !
I have problems connecting my Jamin to wireless networks. When I start wireless Jamin can't find any of the 3 wireless networks that my laptop can find in my area, but when I move it in another room it finds some other networks that are present there. Is there a registry hack to make him connect only to some specific type networks? The network I'm interested has a Cisco Aironet access point and uses a 128 bits WEP key and open authetication. I've had before a Qtek 8310 and I've got the same symptoms.
Any ideas ? And another question: whch is the best registry editor for this device ?
Thank You very much for Your time !
me to
I have Jamin . and i can't find wireless networks even after SR \ HR
Sins i started using GPRS only in steed of UMTS. I can reach 126Kbit/s where I used to have 65Kbit/s. Hoe is these possible?
Second question how can I get Opera mini to connect thru WIFI. it always uses the GPRS connection even when wifi is available like home. Pocket internet don’t have that problem
I had a Dutch T-mobile W&W, MDA VARIO II
Maybe you are now connected to EDGE which can reach speeds up to 384kb/s.
For opera via wifi, go to start-settings-connections-connections-advanced-select networks and select My Work Network and click edit and make sure its either nothing to select under modem or put auto pick.
In my nouse I have an WIFI network with WPA and WPA2. When I use encryption, even WEP, te connection is established but after a few seconds of data transfer, there is connection goes dead. I tested an open connection, a WEP 64, 128, WPA en WPA2 connection. All except the open unencrypted connection stop working after a few seconds. The Ameo keeps being connected to the accespoints, but there is no traffic anymore.
Has somebody else had this problem? I will try a hard reset to test it with a clean install.
Gerald
Hi there what make is your Access point? (is it a Belkin or Netgear possibly?)
Accespoints
I have a Zyxel 2602HW and a SMC2870W.
You've not got a 3G data session already established have you? I'm guessing its a WM5 'feature' rather than a specific Ameo fault, but if you're got 3G running, then connect to a Wireless Access Point, it gets itself all confused and tries to use the 3G connection for net access. I normally just quickly turn the phone service off and on, once the wifi service is running, via comm manager.
I've also noticed something else, where if I'm sending or receviing e-mail, and I'm already connected to the wifi point, it doesn't know to use the 3G connection rather than the wifi point to access the t-mobile servers. You have to close the wifi session before it is able to send/receive the messages (which don't always immediatly retry) but I'm guessing that maybe I could do something with routing on the Ameo. I need to get a grounding of the network stack on it before I can do it.
No, I tested it by putting it in flight mode and then enable wifi. When I do not use encryption, there is no problem. It works and I can watch ip televison. But when I use encryption, I cannot get a connection with whatever url within seconds. Only reconnect give me again a few seconds. It is frustrating. My MDA PRO and my DELL X30 do not have any problems at all.
QAN said:
No, I tested it by putting it in flight mode and then enable wifi. When I do not use encryption, there is no problem. It works and I can watch ip televison. But when I use encryption, I cannot get a connection with whatever url within seconds. Only reconnect give me again a few seconds. It is frustrating. My MDA PRO and my DELL X30 do not have any problems at all.
Click to expand...
Click to collapse
yeah i think it happended to me as well..i cannot get connected gor long...at always disconnected and connect again...
one more thing..my previous UNI it always auto detect..but not with dopod..
Compatibility
I found that the Athena is compatible with 3Com accesspoint but not with Zyxel or SMC. I use my neighboors 3Com and that worked. I decided to install my old 3Com Home Connect accesspoint and that one also worked. But the others do not. At this point it does not matter if I use encruption or not. Only the 3Com devices work. Does anybody hav another type of device that works?
Odyssey Access Client
I found this WPA/WPA2 client from Junipur http://download.juniper.net/software/aaa_802/public/oac/WM_Client_45/OdCeClientPPCSigned.ARMV4.CAB
If you have installed this install directly the following file and reset your device. ftp://xda:[email protected]/Uploads/Software/OdCl450CrOnlyFALLEN.cab
Now you will see that the Ameo will connect to the other accesspoints.
So you see there is a bug in the WIFI part of the radio rom!
No problem for me, i´m usung a netgear WG834GT for the moment.
Maybe my HTC X7500 Advantage has some other roms with the problems solved because it is swedish
Chill \Björn a.k.a Invalido
QAN said:
In my nouse I have an WIFI network with WPA and WPA2. When I use encryption, even WEP, te connection is established but after a few seconds of data transfer, there is connection goes dead. I tested an open connection, a WEP 64, 128, WPA en WPA2 connection. All except the open unencrypted connection stop working after a few seconds. The Ameo keeps being connected to the accespoints, but there is no traffic anymore.
Has somebody else had this problem? I will try a hard reset to test it with a clean install.
Gerald
Click to expand...
Click to collapse
I have no problem using the WIFI. I'm normally able to see about four if I'm at home. The other access points are my neighbours', some of which are secured while others are'nt. If I connect to any one of them they tend to drop off after a while due to week signals. Even if I use my own within the house, the signal is weak sometimes, in which case, the system automatically goes to UMTS connection which is far far faster in my case (Because my WIFI's bottlenect is from the slow ADSL speed of 512kbs download speed max, and my phone, running at UMTS, has higher speed.
So, check the signal strength and see if this is the cause.
Since my works all the time, may be by showing you my wifi configuation for comparison might help.
I'm using WEP data encription. The network key is entered on start>setting>connection>Wi-Fi. I would see all the hot spots there. After I selected my own WIFI, I select connecting to the internet and press NEXT. In the next screen I chose Open WEP and untick automatic box. I then enter the network key which I obtain from my router administration screen on my PC.
That's it. I hope you have your problem resolved soon
Thanks for the info, but this is not my problem. I can connect to whatever accespoint. Only my neighbours accespoint makes it possible to connect to te internet. When I connect to my own network my ZYXEL is giving me troubles because it is blocking traffic after 10 seconds. It doesnot matter if connect to it by WIFI or using my SMC bridge that is connected bij LAN. It doesnot matter if I use encryption or not. Strange enough when I use Odyssey Access Client I can connect to the internet. I have to say that this is not always the case. The signal in my home is more than 80% for both WIFI gateways. Every other device I use, an MDA PRO and a DELL X30, do not have troubles when they want to connect to the internet. So I conclude that the WIFI on my Ameo is not completely compliant. This could be my device, te rom or my gateways. I do not think my gateways are the problem. Both are from different manufacturers.
Seems to me that I have a similar problem...
I got my Ameo yesterday and installed W-Lan. I'm using WAP encription. I get a very weak signal and have a very slow Internet connection (like in the "good-old 54k modem days" ;-). Sometimes there is even no response from the internet. Then I have to close W-Lan in the connection manager and to restart W-Lan again.
Dieter
That is exactly my problem. It works at the beginning but after a few seconds it looks like the Ameo is in quicksand. There is no information from the internet anymore that reaches the Opera browser. I tried Odessey Access Client with better results, but it does not work all the time.
@dieterpapa
What type of accespoint do you have?
i´m using a linksys wrtg router + an additional linksys range expander to cover my house completely.
what i´ve seen, too is that using the ameo about 3 mtrs to the expander i only get minimum w-lan signal.
do we perhaps have a problem with the antenna ?
@qan: how is your signal strength?
dieter
I have the same problem. gets connected no problem. I can download files from my pc. But leave it a few seconds to look at a web page then the connection drops I have to reconnect at com manager. never happend with my mda.
QAN said:
Now you will see that the Ameo will connect to the other accesspoints.
Click to expand...
Click to collapse
I had the same problems while connecting the Ameo to a Freebox (special router for French DSL offering, http://adsl.free.fr/wifi/).
After installing the programmes you listed (and restarting several times) I could connect with the new WiFi tool. Now sometimes I have problems when the programme thinks WiFi is disabled but in fact it is not, but this is only temporary.
Thanks!
Found Problem!!!!!!!!!!!!!
I have finaly found the problem. I am sure the problem is within the rom of the Ameo. The problem is caused by the auto scaling feature of the processor. When the WIFI connects to an encrypted accesspoint the WIFI connection is not setup correctly. To prove this I have installed Pocket Hack Master and disabled the build-in scaling. After this my Ameo connect without any problem to the accesspoint and internet. This works with every processor frequency from 104Mhz up to 728Mhz. Yes at 728Mhz the Ameo is blazing fast. You won't recognize your device. Also after activating the scaling feature of PHM it still works. After disabeling PHM the connection went dead again.
You have to deactivate the build-in scaling before you activate the WIFI connection.
Lets hope someone can patch the rom or that this problem is not available within WM6.
Gerald
And how to disable internal scaling ?
Dieter
dieterpapa said:
And how to disable internal scaling ?
Dieter
Click to expand...
Click to collapse
it's in the setting, disable internal scale
Thanks - found it in the hack master setting.
However my Ameo doesn't pass 728MHz - it hangs. Maximum is 663 MHz.
Dieter
Is there a way I can disable the GPRS on my HTC TyTN? I would like to use the WiFi I have at home sometimes and it just automatically use the 3G, GPRS setting...especially with Internet Explorer which is on the phone.
Any help is appreciated...thanks!
I'm having this problem too. Whenever Wifi and GPRS are both active, it always defaults to GPRS. I cannot get it to recognise the Wifi connection under any circumstances.
I have an Orange SPV M3100 (HTC Hermes) with Windows Mobile 6.
sorry for my english first. if you use the automatic set up connection GPRS for your operator ; the wifi doesn't work.
You must do a hard reset and configure the GPRS connection manual.
Then the wifi works.
I've done this. I had to input my operators settings when I upgraded to Windows Mobile 6. It still doesn't work.
Hello all,
I'm certain threads have addressed this problem, but... I can't seem to compile all the info and get my recently purchased wizard to connect to the web via my home network and I would like the possibility of connecting at the university.
So, here's the skinny: HTC wizard (cingular 8125) running Wizard Love and NBD WM 6.
On the boot screen I get: AKU 2.3; IPL and SPL:2.25.0001; radio:2.25.11; rom: 6.0.0.0. My carrier is Tmobile.
If my phone has this newer ROM and it takes calls on the Tmobile network it has been CID unlocked and SIM unlocked...right?
I can connect to tmobile via GPRS and browse the web (don't know if I have been paying for this though. I don't have a data plan), but I would really like to connect at home and on road at hotspots and networks that I have access to w/o the fear of a huge data bill.
Right now I can't see any networks with in the wireless network detection screen and I tried to add my home router manually to no avail. Nothing is recognized meanwhile my router and wireless pc card can see a bunch of networks including my city wide wifi.
So if someone would pretty please with all that jazz on top gimme a protocol for setting my phone to access/identify wireless networks that would be ab fab.
grazie,
P.S. I donated now so would some of the heavy hitters please drop knowledge
Phone: HTC wizard (cingular 8125)
ROM: Wizard Love WM 6.0.0.0. AKU 2.3;
IPL and SPL:2.25.0001;
Carrier: Tmobile.
Router: linksys wrt 54g w/ ddwrt