In the last night I flash file "os1.11wwe_bigstorage.nb1" form ftp.forum.xda-developers.com/Magician/BigStorage_ROMs in my xdaIImini by program romupdate.exe for make it to bigstorage
When it finish the device message "checksum errot"
after i reset my device it can't access to bootloader mode
Who can help me????? please!!!!!!!!!!!!!!!!!!!!!!!!
PS now i can't use my device because it can't switch off
Related
I was updating my new i-mate SP3 (typhoon) to the latest i-mate ROM 2.4.33.11 which completed successfully but now every time I turn on the phone it goes directly to the bootloader tri-color screen. I tried several times to update the ROM again but it does'nt help. It shows the proccess completed successfully but the phone is still stuck in bootloader mode.
In the bootloader screen it shows the following
IPL 1.00
SPL 2.5.0102
I even tried to flash the ROM through an image of Orange4114_ALL_SPL1010091 on a miniSD card but it gives an error message
"Not allowed update!"
Please help me figure out how to get my phone working again.
Same PROBLEM here HELP..!
Exactly the same problem if anybody can help ..please do.
spl
hi
same problem my sp3
SPL
Same problem on spv c500 stuck in bootloader but with 2.05.0130 SPL
sp3i stuck
Hi all,
I have the same problem, but I didn't try the mini-sd boot.
surfturtle, will you kindly send me the way?
Thanks
Hi guys...
I don't have the Typhoon and don't know if this will work for you, but this is at least how we fix this problem on the Hermes:
Enter into bootloader using mtty.exe and run the command "set 14 0" and "task 8". Phone will reboot and start OS.
If it doesn't work, then try the SD flash method mentioned by surfturtle. Keep in mind that if your device is not superCID the image file should match the CID of your phone (must be an original shipped update from your vendor). This method consist on:
1) extract the rom image from the rom upgrade exe (winrar or cabextract can be used for that) and you'll find a .nbf file.
2) Rename it to TYPHIMG.nbf
3) Format your SD card in FAT32
4) Put TYPHIMG.nbf on the root folder of your SD card
5) put sd card on the phone, and enter into bootloader
6) confirm flashing on screen, and wait until the process is finished (do not reset it, will take about 30min).
Check the hermes wiki if you need more information on any of this.
Good luck!
sp3i stuck
thanks pof,
but where would I get mtty.exe and where will I see "set 14 0" & "task 8"
thanks again.
Re: sp3i stuck
@Tall_Man: See the hermes wiki:
http://wiki.xda-developers.com/index.php?pagename=Hermes_BootLoader
http://wiki.xda-developers.com/index.php?pagename=Hermes_UpgradeProblems
http://wiki.xda-developers.com/index.php?pagename=Hermes_SDCardFlashing
I-mate ROM
Hi, I did the upgrade through the PC but the device info still shows the old ROM: 2.1.33.13 No error messages and the phone keeps hanging on me.
Is this version of ROM the Arabic one? If not, can someone post or point to where I can download the arabic version? I did not find it on the I-mate website.
Thanks in advance,
I-mate SP3 (?rom 2.1.33.13)
A disaster!
My very good friend (Qtek S100 Italian) have a big trouble!!!!
Now it's on boot loader and no way to go out :shock:
I think that the rom was f**ked, I try with a SD with the rom(I used Multi-port/USB TTY Ver1.11a to do it with another Qtek) but the PDA don't show the download menu
I tried with the original ROM from Dangard but the program say that the rom was not for my device
I used the MaUpgradeUt_noID, but it's not working
the pda screen is always on boot loader, changing only from serial to USB (when I Connect)
I don't know if I can use Multi-port/USB TTY to solve my situation, I tried to use the lnb command but the answer was that I have not the permission
By the way, I disconnect the battery and wait, but when I give power I have always the boot loader
Any way to help me? tnx
Stefano
Hello,
I was trying to upgrade the O2 XDA II and in the process, it created an error. The upgrade was terminated, when I try to hardest the device and put it in boot loader the screen went blank. The Mtty.exe doesn’t work with USB anymore it gives an error “USB port can not open”. Any suggestions will be appreciated.
Thanks
after the charmer rebooted, there is a white screeen on it. i did hard reset but i did not help me. i got the battery out too but no no.
please help me.
Try entering bootloader mode and flashing the rom once more.
bootloader
yes i did it but couldnt be successful
i doesnt
Bootloader mode:
[Record] or + [Power] + [Soft reset]
[camera]
screen is always white and is not connected with activesynce.
thanks
call to your phone see if unit is working
when i call the charmer i hear the mail box .
it is not connected to pc too.
i dont know why i cannot be succees bootloader
now i can bootloader mode,
i did it but got this error while i upgrade my rom to newest rom 3.3...
it means in english : please check your NBF data, this NBF data cannot be used for your PDA Phone.
and if i want to install the rom version of compactII_AKU2.0_05-2006 i get such as error error 296 :this NBF file cannot be used for your PDA phone.please get newer NBF file.
what does it mean boys...
please help....
You probably have the 3.xx bootloader, find the german AKU 3.3 and flash it.
yes i found it
if i want to install the newest rom also ger.3.3 i get such as error what there write on jpeg at attachment mean in english
"please check your NBF data, this NBF data cannot be used for your PDA Phone".
Try some prophet rom with noid RUU.
where i can get it from.
please give the link.
thanks.
sorry, I'm sick and tired of providing everything for everyone. Go to prophet section and find a wm5 rom.
<salute vlodeck!>
danke an alle
thanks friends espacially vlodeck
my problem is solved.
use this link to solve it
http://forum.xda-developers.com/showthread.php?t=301323&page=2
Hello, please can you help me! I only had my PDA repaired a couple of days ago, i needed to unlock it and i used your intructions for unlocking the XDA II but it did not work.
After following your instructions and opening the program xda2unlock and typing "yes" the program came up with the message:
"ERROR: OpenComport \\.\WCEUSBSH001 - the system cannot find the file specified"
The PDA is showing "serial v1.06" and "usb v1.06 when in cradle, it wont do anything like before i had to get it "reflashed" by the company.
What can i do??
Thank you!!
Nieko
connect it to usb and falsh a rom on it
the wifi and the readme of the rom file describe step by step how you do it
Struck on Serial
I do have the same problem. What would be the best ROM plz. All the ROMs I downloaded gives error as "102 Image File Checksum Error" or Language ID Error". Pls give me a good link for a working ROM.