hi
I have downloaded the wm2003se from lumpinstefan and i could change the rom of my pocket pc to that version by using activesync.
Now i downloaded another version of the rom and i tried to install it on my qtek 1010 (wallaby) and it in the black window on my computer appears:
"ERROR: GetConnectionType - An existing connection was forcibly closed by the rem
ote host.
error getting connectiontype"
When i press the next button in the setup it says " cannot execute the remote communication prgram. please make sure that USB/Serial is properly connected". and the setup shuts down.
i Need You to know that before the new rom i downloaded from lumpistefan i was using pocket pc 2002 on my pocket pc.
Now it's clear that there is some problems in the connection. i tried it on several computers but i faced the same problem. is there any setting on my pocket pc to change??
Please somebody helps me i really need to know how to solve the problem.
Regards, and thank you.
hi ng!
i need a solution to use my pda qtek 2020i as "modem-device" for my linux pc.
i managed to get a rfcomm0, can send at-commands via this device, could dial out with a local software on my pc.... but,
if i try to use p.ex. efax - efax tells, that the modem does NOT support fax.
is there any way to solve my problem?
thanx a lot for any hints.
mario
ramsesii said:
i managed to get a rfcomm0, can send at-commands via this device, could dial out with a local software on my pc....
Click to expand...
Click to collapse
Can you do GPRS ? AFAIK, the gprs and fax data
go over different serial channel than the
AT command channel. You will find more
info here:
http://wiki.xda-developers.com/index.php?pagename=HTC_GSM
http://wiki.xda-developers.com/index.php?pagename=BlueangelProgress
hi!
yes - i can do gprs!
the problem is, that a sdp browse MAC only gives me channel 1 for serial connection, channel 2 for dial-up networking, and other channel (audio, file transfer,...).
thanx for the 2 links - but, the second is for mobile phones with linux on it - the first couldnt help me out.
i use normal windows mobile 2003 on my qtek 2020i - not linux (maybe i will sometimes )
any other ideas around?
thanx
ramses
ramsesii said:
the second is for mobile phones with linux on it
Click to expand...
Click to collapse
The hardware information doesn't depend on
the operating system
- the first couldnt help me out.
Click to expand...
Click to collapse
You can see that all the phones
use AT+FCLASS=0 as an init string.
What is the reply to 'AT+FCLASS=?' on alpine ?
You can also try:
AT+FMI?
AT+FMM?
AT+FMR?
AT+FCC=?
AT+FCQ=?
unfortunatly - nothing works.
my rfcomm is up: fcomm0: 00:09:2D:2B:EC:3F channel 2 connected [tty-attached]
but in minicom, which is connected via rfcomm0 all i get is...
Press CTRL-A Z for help on special keys
OK
at+fclass=?
ERROR
at+fmi?
ERROR
atdt
OK
AT+FCLASS=?
ERROR
AT+FMM?
ERROR
AT+FMR?
ERROR
AT+FCC?
ERROR
AT+FCC=?
ERROR
AT+FCQ=?
ERROR
quit
ERROR
exit
ERROR
bye
ERROR
AT+FCLASS=0
ERROR
this sounds.... not good
or am i doing something completely wrong?
thanx for your help.
ramsesii said:
at+fclass=?
ERROR
Click to expand...
Click to collapse
Hmm. Works as expected on my Universal.
It has something to do with your radio firmware,
maybe needs some special setup, or it is
simply not supported.
AT+FCLASS=0
ERROR
Click to expand...
Click to collapse
I don't know how the AT debug works on alpine (look up the registry keys in the wiki for himalaya), but
you may enable it, and PM me the log.
p.ex truefax works on my device... with it i can fax-out.
maybe i will go on that solution - is not what i wanted to have (faxout from the pc directlly) - but better then nothing.
hope RECEIVING fax will work with it.
thanx a lot for your nice help.
Hi,
I try to run gpsproxy on my m3100 and :" the garmin protocol output extension failed to start: CreateFile failed :55 "
I would appreciate any help
Thanks
Any one can help me on this issue, please?
Please help guys,
Every time I try to connect to the internet using Activesync I get the following Message:
"The page you are looking for cannot be found due to unknown error 0x80072f78"
I'm using activesync 4.5 and crystal v4 WM6 rom on I-mate Jamin
Please note that I have no problem connecting to the internet using WIFI
Please help
Thanks to all
H.S
It might be due to enabling the advanced settings of the USB connection.
Go to settings-connections-USB toPC and then disable the advanced network
Thanks man, it works
thanks again
i have jamin wm5 , and i have the same proplem
so if eny can help me in that
i try to do go settings-connections-USB toPC
but i didn't find usb to pc
so plz help me in that
i try found eny soleution from 2 weeks but i didn't
I'm new in windows mobile and i don't enything about it
thanks
ahmedara said:
i have jamin wm5 , and i have the same proplem
so if eny can help me in that
i try to do go settings-connections-USB toPC
but i didn't find usb to pc
so plz help me in that
i try found eny soleution from 2 weeks but i didn't
I'm new in windows mobile and i don't enything about it
thanks
Click to expand...
Click to collapse
try this reg fix. unzip file. copy to ppc and run
Hi Dear Friends.
I Installed the ****fPda 15 . all the things work properly.
I connected to my WLAN and The Web Browsing is OK. but when i want to Connect to My VPNs (which works in PC), An error like this appeared : "UNABLE TO CONNECT TO THE NETWORK. DO YOU WANT TO TRY AGAIN ?"
and when I want to Update Weather the "Network Timeout" error appear.
so what I have to do ?
please help me.
tnx
plz help me friends.
I really need this.