Problems with SD card on XDA2 after unlocking - MDA II, XDA II, 2060 General

I started using a 512mb Apacer SD card a couple of months ago when I installed TomTom3. It worked fine. Yesterday I did a hard reset and ran the bootloader method of unlocking the XDA2 with the SD card left in. The device no longer recognises the card, but it does see an old (Hagiwara? -brand name too small to read properly) 64mb card if I put that in.
Can a hard reset or bootloader unlock damage an SD card? Any suggestions? :roll:

The card was faulty and the vendor replaced it.
I now have a new Tom Tom problem. "Cannot open Com1 port does not exist". I thought this might be to do with bluetooth headset, but that works fine. :shock: Did another hard reset. Re-installed Tom Tom 3 and the same message comes up. Any thoughts?

Related

SD Card not recognised in file explorer

Hi all,
I have searched hi and low for the resolution to my problem. I have owned a Magician (sold as Xda II Mini) for just under a year and have a 1Gb SD card (eagletec turbo 66x speed) which has worked beautifully until two days ago
File explorer does not recognise the SD card. I have tried the SD card in other devices (e.g. PC - using a card reader, digital camera, dvd player, my friend's pda etc...) and it works fine.
I have tried inserting different SD cards into the Magician and they all get recognised ok.
I have tried soft reset and hard reset to no avail.
I have formatted the SD card using a card reader on the PC (tried both FAT and FAT32) and also tried formatting it in my digital camera.
When I insert the card into the Magician (from power off state), the Magician does light up indicating to me that there is no problem with the spring load mechanism of the expansion slot. What is strange is that when I go to Settings->System->About, I get 'Expansion Slot: Not in use'
I also tried (after a suggestion in another post) to add a "shim" of plastic of paper on the contact side of the SD card. No use.
I am reluctant to flash the ROM as I have not had any other problems with the Magician to warrant it.
Any ideas?
Have you tried cleaning the contacts of the SD card? Try soft resetting with the SD card in it.
Hi thanks for replying.
Yes I have cleaned the contacts of the SD card and also tried many soft resets with the card in and also with the card out.
????
Hello,
Try formatting your card with a different reader or from a Nikia phone.
Regards
Carty..
I have tried formating the card in several card readers. Still not being recognised is file explorer. Again, the card does work in any other device I put it in - just not my mini
Anyhow, I'll just use a different card for now. Just wondered if any other people had the same issue as I do.
Thanks all.
for me the same **** happened with my new, exchanged, mdac. using the sd card with the previous machine was no problem, now the card is not being recognized at all. using it in notebook, camera ... no problem.
any ideas?
i dont want to start another thread but im having the exact same problem with my MDA Compact II. I have a 1gb Toshiba SD card that wont even work in the MDA but it works fine on my camera and PC. So I would like ot know if there is a solution to this
Thanks
Hi all
I am a newbie and am experiencing the same issue, external sd card not showing up in file explorer.
Sniffer can find it and I can play media files from there. Is this the norm or do I need to change something?
I am using C&C 1.5ghz Froyo Combo VERSION 8 final.
The 16GB card is seen by all other card readers I have tried.

Memory card problem

After using my vario 2 for a while the mem card becomes unusable.
It's shows no free space at all. I have a 1 gb memory that came with my t-mob vario 2.
My mp3 ring tone doesn't work anymore. I have to remove and reinsert the memory card or soft reset the device.
Radio 1.20.31.10
Rom: 1.21.114.3
Any idea's what could be the problem?
Thanks
The smilar problem occured with one of my XDA-II (Himaliya), Even though I have hard reseted the device. Finnaly I have backuped the card through the pc and format the card (on PC) and it wasn't working, even though I have tried 3 other cards and they were working absolutely fine with the device. What I did was to leave the card inside the device for overnight and it was recognisable in the morning, then I took out the card from the device to put the data back from the PC and once I have put the card back in the device the card wasn't recognisable again, So finaly I left the card again in the device overnight and it was recognisable again, then I left the card in the device and put the data back through the syncronisation.
I haven't taken out the card since then because I know there is some recognising problem between the device & the card, its working since then.
My Advice is : To check another card and if that would work then try to sell your current card and buy another.
My advice 02: Try to backup your device, leave the card inside the device and HARD Reset the device & once the device will install newly it should configure the card as well.
I have got very usefull software "storagetools" (trial) by which you can scan, format & defrag the card, you can try it.
GoodLuck
Sidd
Use chkdsk on the PC to check your storage card (instead of any PPC-based software, including Storage Tools). I also recommend the thread at http://www.pocketpcthoughts.com/forums/viewtopic.php?t=39583 on all these q's.
On a related issue concerning problems with microSD cards and the TyTn, I have a problem which I hope you can help me with:
I have a new TyTn (ROM Ver. 1.18.255.3) with a 512mb miniSD card. In the course of my usual usage, the device hanged and after a few minutes of unresponsiveness, I reset the device using the reset button. When it rebooted, the card is no longer recognized by the phone. I used a card reader and WinXP and Mac OSX cannot also recognize it. If I try to format it (XP), XP says that the card cannot be formatted. I tried using it in my Samsung D820 and it cannot also be formatted. I then concluded that the card was defective and bought a new one (512mb).
After using the new card for a week, my TyTn hanged while accessing a program installed in the card. Again after a few minutes of unresponsiveness, I rebooted the phone using the reboot button. When the device booted-- Bam!!! the card can no longer be recognized by my phone! Windows and Mac OSX cannot mount it. I tried the unrecognized card in my Samsung D820 and it is recognized! I inserted the miniSD card (128mb) originally in my D820 in my TyTn and it is recognized/read by the TyTn. I formatted the defective card in the D820 and copied a few files in it and the D820 can read those files but my TyTn can't! I tried the other 128mb card on my TyTn, formatted it and copied files into it and everything's fine.
How come then that the 512mb card can be read by my Samsung phone and not by the TyTn? My TyTn is certainly not defective because It can access the 128mb card that was originally in my D820. As I stated earlier, I have already formatted the 512mb card in my Samsung phone and have transferred files into it (The Samsung phone can read the files written on it).
I have re-inserted the 512mb card numerous times in my TyTn to no avail. I have also rebooted my TyTn several times and still it cannot recognize/read the 512mb card. I am now using the 128mb card that I originally use in my Samsung D820.
If it can help, I have enabled and unlocked my TyTn's extended ROM. I have a few programs that are installed in my Ext ROM.
Thanks!
Similar card problem
I recently purchased the T Mobile MDA Vario2 with the CoPilot 6 software. worked fine for about a week and then the CoPilot software which was running from the memory card started to hang intermittently. The first couple of times a soft reset cured it. Then after about the third soft reset, the memory card was no longer recognised. Tried reading the card via my pc and that couldn't recognise it either.
Took both the phone and card back to T Mobile where a new card was tried, this was recognised immediately so I now have to take the whole CoPilot package back to be replaced.
I have also just orderd a new 1GB sandisk card from Amazon and am now concerned that this is going to be a repeating issue. I wonder how many other owners have had this problem and if it is actually a fault with the Vario2 or wether I have just been unlucky with a dodgy memory card.
Would appreciate other thoughts on this.
Cheers
Matt
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
amf said:
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
Click to expand...
Click to collapse
How did you work that one out?
Elwyn M3100 said:
How did you work that one out?
Click to expand...
Click to collapse
Because when I enabled it, the corruption started.
amf said:
Because when I enabled it, the corruption started.
Click to expand...
Click to collapse
Hmm, yes, I can see where you worked that one out

Help SD card Problem

Hello! Although this is my first post on the forums, I have been reading extensively through these forums for the past ferw weeks since my acquisition of my new to me MDA (i.e wizard G3). Yesterday, I took out the sd card for a few hours and now when I put the card back in the wizard is not recognizing the sd card in the file explorer. I put the card in the PC and it is recognized fine there. I reformatted the sd card via FAT and inserted it back into the wizard but no luck. I soft reset the phone several times but in vain. I then eventually hard reset the wizard and THEN inserted the sd card but still not read. I tried going through the My computer--> Manage --> Disk Management but the sd card is not showing up on it.
The sd card is clicking in and out fine from the wizard. Any help would be greatly appreciated. All my medical programs were on the SD card. And with that many programs I cant just work off of the memory.
Thanks in advance
Sohaib
update
I installed the wm5storage and the program does not recognize the sd card either
Update
-Tried formatting to FAT with computer and re inserting did not work
-Tried Formatting with WM5storage and THAT didnt work either
-CID unlocked the phone, installed 3.08 ROM, and then "Crossbow reloaded" with 2,19 UK Radio Rom, tried inserting the sd card and still not work
-Tried formatting with "Flash Format" and the program says "no storage card detected"
I am thinking that I may have damaged the pins or something when I was reinserting the SD card, initially when I noticed the problem
2 options in front of me now!
1. buy another mini SD card and see if that works
2. Open up the Wizard to see if it is a hardware issue
Opinions etc would be greatly appreciated
thanks
sohaib
Ive got the same problem with my Qtek 9100
hi i had a near identical problem occur with my xda mini, as in after removing and reinserting my sd card it was not being recognized. i happened to have a old mini sd card (only 64mb tho!) and that was recognized. so i just bought another 2gb sd and its been fine ever since, but saying that i have not removed it from my mini yet! which is getting a little annoying now as i was given a copilot kit and the software is on a mini sd card
Try removing all formatting and then allow the phone to format your card. I had a problem with my second MiniSD card after formatting on my PC.
Insert your card into your card reader. Right click "My Computer" and click on "Manage". Then left click "Disk Management", find your card and delete the partition. At this point, you can then stick the card into the phone and it will ask if you would like to format the card. Even though the computer will not recognize the card, your phone will.
Snapin Disabled
I tried the approach of right click my computer--> manage --> disk management --> but it tells me that the snappin is disabled and when I go into start--> run--> gpedit.msc --> to enable the disk management it still does not recognize my storage card in the disk management. Hence I am unable to remove the partition.
Thanks for the replies guys, any suggestions on how to enable the specific snapin on XP?
Thanks
Sohaib
New Mini SD Card
OK, so in attempts to diagnose the problem, I went out today and purchased another 1gb minisd card, inserted it into the wizard and................NOTHING. Still no luck. Does this narrow down to the problem to a hardware pin related issue? Or could this still be a software problem. I figured that a new sd card may resolve the issue but unfortunately not, any suggestions would be greatly appreciated.
Thanks
Sohaib
Bump
Ideas? Suggestions? Recommendations?
Thanks in advance
Sohaib
If you tried another card and a new ROM, I would say it is a hardware issue, if it's still under warrantee then I would send it in. If it's not and you want to try to fix it yourself, there is the HTC wizard maintenance manual (Google search) that will give you step by step instructions on how to disassemble it. Or sell it on eBay then use the money to buy a new one.

SD card issue?!

I'm going to buy Gene and read a lot of possitive oppinions abiut it. But there is a discussion on a russion forum www.4pda.ru about SD card problem. As I understood sometimes it looses SD card and everything on it. The files are shown in wrong symbols and even more - sometimes all data are lost. Does anybody had the problemm? know the solution? Thank you.
Get a reputable brand. I once had that problem with a 512MB in Imate JAM, but my Gene has a 1GB Apacer and Ive never had problems. Get a miniSD with an adapter for more versatility.
i have sumtin to tell
hey i bought my gene say three months back.put a 1 gb Transcend SD...but after some days when i took it out and again inserted it...the memory was lost and it was not formatting also....one fine day suddenly my treo recognized the card..but with only 480 MB.....i had to finally buy a new SD for my Gene...
They say SD card should be inserted after soft reset and will work fine. Also there e few guys tested MMC cards and said there wew no problems.
same here
makler1981 said:
I'm going to buy Gene and read a lot of possitive oppinions abiut it. But there is a discussion on a russion forum www.4pda.ru about SD card problem. As I understood sometimes it looses SD card and everything on it. The files are shown in wrong symbols and even more - sometimes all data are lost. Does anybody had the problemm? know the solution? Thank you.
Click to expand...
Click to collapse
hey i got the same problem to. talk to the HTC CustomerCare. they asked me to get my PPC reflashed. it might be due to some ROM error.
but if u try restarting (soft reset) ur PPC. it will work normally. i have used this technice. it works fine with me.
I recently came to a big problem. my storage card is not working correctly. my ppc takes a lot of time in accessing and reading it and sometimes gets hangs while doing it. i tried formating my device but the problem still exists. then i tried formating the memory card with my PC but again something strange happened. While formatting my pc gave an error msg "Windows Can't Format" or something like tht. i tried to manually delete the contents of my memory card but it says can not access device. I am sure tht my card is not Password lock. i think the problem occured after i used "WM5 Storage" software for my PPC to act as a "Mass Storage Device".
plz some1 tell me how can i fix my memory card.
plz plz plz plz plz help..........
yes, it is definitely a big problem with the SD card problem, i mean not the SD card problem, but the Gene's Problem! i bought it 2 months ago for my wife, comes with a brand new Transcend 1GB SD card, after i've installed all the programs into the SD card, its seems ok at first...BUT, when the Gene go to the standby mode, & u wake up the Gene, the program u have installed in the SD card all GONE!! the device can't find any thing in SD card & it finally hang! it is definitely not bcos i m using lousy brand SD card, i've tried Kingston, Pendrive, Sandisk & it has the same problem! i've called HTC service centre in Malaysia (i m from Malaysia) & they dun even knew about this (& even they gave me taiwan HTC email address, & told me to get an answer from taiwan).....
i have no choice, i have hard reset the device for more than 10 times, believe me, i started my pda phone live 5 years ago, i knew what is hard reset...& i tried more than 5 SD cards... same problem, some of the cards facing difference problem - the data saved in the card became unreadable & weird symbol.
since the service center does not has any solution for it, i have to use my own silly stupid way to prevent the Gene Hang, i have set the device all the time alive & avoid going to standby mode, & the problem solved...never hang again...but...imagine...the battery life ....(sigh).....
i sincerely hope that there is somebody in this forum could help to solve this BIG problem.....
At me too a problem with SD card... Very often on a card some files and folders are renamed in not clear symbols and data vanish.... A problem not only at me.... It at many, and it does not depend on a card memory from insertion Gene...
SD Card got Locked
I installed a software on my Gene, named "WM5 Storage".
it allows u to access ur memory card without activesync, as Mass Storage Device.
after the first use i found my card locked. it was unreadable. my ppc also started hanging. i tried restarting my ppc. now i was able to acces my storage card from file explorer, but it takes around 15-20 minutes and another 15minutes to access the files. when i connect it with my pc, active sync does not detect the SD card. i also tried to format the SD card through a card reader. the card reader reads its root files but couldn't access/open them. when i tried to format it give an error "device not accessible. device not ready.".
i also checked the lock button on the card, it was unlocked. plz some1 help.
plz plz plz..
mee too
GUYS I HAVE ONE CARD WITH ME THAT IS PERFECTLY OK...BUT DOES NOT GET READ IN MY GENE.....IN MY TREO 680 IT SHOWS ONLY HALF MEMORY....AND MY LAPTOP IS ALSO NOT RECOGNISING IT...WAT TO DO....???
I have the same sd card problem.......can anybody tell me the solution?is there same problem with mmc card? if no them i'll buy a new mmc card....plz help me.
Count me in
I had this problem for 5 times and still has it. Actually this happens(based on my experiences and opinion only) when u install some software on the SD card and it damages the file system.
Solution might be not to install apps on SD card or use a RS-DV-MMC which is used in recent Symbian phones.
Give it a try...
And plz post feedback.
Enjoy....

SD Card Woes

Hi,
I've had a 1GB SD card in my wizard for months with no problems at all. I had some software installed on the card and the other day I wanted to free up some space so I uninstalled the apps that were on the card (SPB time, SPB shell and Brain school)...Since then, my phone does not recognise the SD card. There are no errors or anything it just doesn't register that the card is there. I've done a factory reset but this has not helped.
I'm running WM5 with a moleski updated ROM that has been on the phone probably a year or so
Any ideas?
I guess the card must be knackered, I tried it in my camera and the camera wouldn't work either. weird how just removing software could kill the SD card...
Run the card in a card reader on a computer. There, you should be able to do a long format/bad sector search. This will tell you once and for all if it's dead. It's the only way to be sure.
i have exactly the same problem and its happened twice now. the data is fine on the card just wm5 doesnt recognise its existence any more... if you wipe your phone and start again it pops back to life
I've tried a factory reset (hold the four buttons then press send) but this hasn't fixed the problem....I need to buy a card reader I guess to check for sure

Categories

Resources