Related
Hello,
I will offer 15 Euro to whom will give me a solution to pass the GSM error (1% error).
I have a T-Mobile PW10B-Model. I tried to upgrade the RSU to RSU_V6.25.02. Maybe because the battery wasn't full, the upgrade failed.
I followed step-by-step the procedure from "http://wiki.xda-developers.com/index.php?pagename=Wallaby_HT_GSMError" but no success, I still have the 1% error...
I read that there is a tool called repair.zip, but I didn't find it.
Please try to help me...I don;t have money for another pocket
Thank you,
Flavius
Re: 10 Euro for helping me!!! (paypal)
15 EURO !!!!
Re: 10 Euro for helping me!!! (paypal)
this is what I did:
How to fix GSM Error Problem ....
Download the XDA-Developers ROM Version 1.1
Install the ROM on your Device via SD-Card and bootloader.
The phone should start up and give you the screen allignment and the whole menu!
Download an Upgrade for your device. This depends ont the model you are using. Check the sticker at the back of your device.
If it is a PW10A-Model download RSU Version 4.16
If it is a PW10B-Model download RSU Version 6.24.20
Extract the downloaded ZIP-File and copy all files to the /Windows directory of your device.
Copy the RSUpgrade.exe additional to the /windows/startup directory.
Make an soft reset of your device.
Maybe the upgrade will stop again at 1%, this may occur when you have an empty battery.
Re: 10 Euro for helping me!!! (paypal)
And this is what is not working:
Place your device in the cradle. Run Active Sync on your device. (I did this...the Active Sync runned for a lot of time)
------------------------------------------
The RSU Upgrade will run in the background.
Wait for about 10 Minutes. The upgrade should complete in the background....
Afterwards all should work again...
--------------------------------
HELP!!!!
Here are the repair files, and instructions are included. I hope this is what you're looking for.
You'll need WinRAR to extract the files.
grayhaze said:
Here are the repair files, and instructions are included. I hope this is what you're looking for.
You'll need WinRAR to extract the files.
Click to expand...
Click to collapse
thank you...I tried with both cabs but the same 1% error (
I think it's hardware problem
It seems that it is hardware....
who knows what should I change? the gsm module? the mainboard?
has anyone a service contact in Czech Republic?
Please try these:
IamGuest said:
Please try these:
Click to expand...
Click to collapse
thank you...I tried ..is not working...for sure the only posible way is to flash the GSM rom from SD card using bootoader...but I'm not sure if is posible..
Does anybody know how can I "modify" the mainboard to make the battery to recharge? (except the back connectors for extra battery)
All,
I've exchanged many emails with the imei.check.co.uk team and also met personally one of these guys in order to be able to upload a new ROM to my O2 Orbit. I had excatly the same problem as many of you with ending the uploding process with "model invalid id" error message.
Now I'm happy to say we do have a solution.
So if you want to change your ROM (any), simply follow these instructions:
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Of course you can publish the instructions...
BUT PLEASE put a BIG WARNING! It will crash the phone in case you don't have a valid key file to perfom the last step: RUN THE UNLOCKER AGAIN AFTER THE ROM MODEL SWITCH TO RECOVER FROM THE DATA CRASHED MESSAGE!
Hello,
we found a way to flash ANY artemis roms in ANY Artemis look alike device (HTC Hero too).
Tools you need:
-hexworkshop from http://www.bpsoft.com/downloads/
-Any rom
-winzip or winrar
-http://www.imei-check.co.uk/C3v1Unlock.zip
a valid UNL file for your phone.
install hexworkshop and winzip/winrar
Take any rom for example: ART_HTCWWE_11240501_026790_WWE_Ship.exe
in explorer, right click on it and select "Extract files..."
Now it will unpack all the files
You'll have now "HTCWWE_shipsigned.nbh"
right click on it and Click "Hex Edit with Hex Workshop"
You'll see on the 5th row ARTE10000
Make it ARTE***** and save file
Now right click on ROMUpdateUtility.exe and "Hex Edit with Hex Workshop"
Search for word password.it will find it at 0x3E0B0 after password replace "BsaD5SeoA" with "IMEICHECK" and save the .exe file
Now connect the phone to the pc (normal way). run the C3v1Unlock.exe
when is asking for UNL file, disconect the phone from pc, press cancel, and
close the unlocker.
Now connect the phone back to the pc (in this mode it is) and run the
ROMUpdateUtility.exe
Now follow the instructions as the upgrade it will work.
After upgrade done, run the unlocker again and this time select the correct UNLfile.
Task Done.
C3 after flashing with any WIFI roms it will STILL not have WIFI!!!
Regards,
IMEI-CHECK Team
xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx
Cheers, Martin
YESS, I have changed my GER rom to new HTC official ENG Rom, you are the best!!!!!! It's very simple to do...
yuppyyyyyyyyyyyyyyyyyy
the next step is.... backup the ROM I'm search ITA ROM form my HTC 3300.
see you later...
Good Discovery,
But the key is: We will have to pay 38USD for the "Proper UNL file" which is unique for every IMEI. Is it right?
Yeah, Thanks mr. Martin who is from Imei-Check Team. But we are still looking for a free solution.
Regards!
Tamagochi,
yes, first you have to go to imei.check and pay for the unlocking program and the unique .unl file.
P.S. I'm not a member of imei.check, just had the same problem as many Orbit users here...you can find my previous thread.
Works great on all versions.
Great support from the boys from emeicheck
Question about directions
Okay, I'm gonna try this. Do I still follow these directions exactly even though I have already unlocked the CID?
Also, when you see the line "ARTE1000" do you actually replace the "1000" part with the little stars? Sorry, I'm really new at this!
Thanks!
Yes you must do it all.
HELP
Everything went smoothly but when the device rebooted, it want me to "align the screen". It doesn't seem to be able to detect the stylus touching the screen! Can't get past that screen! Anybody know what I could have done wrong?
REF: HELP (Never Mind...)
I DID IT, I DID IT, I DID IT!!!! Just had to wait a minute or two and then everything seemed to work fine!!! TomTom is there, my WiFi is working! Thank you MAROSV and FRANCOBANCO!!!! If I can do it, ANYBODY can!! THANK YOU!!!
Hi KleineMaus,
I am wondering which ROM u used on your orbit that includes tomtom?
Or do you just mean you still had tomtom stored on your menory card?
Cheers, Towelie.
towelie said:
Hi KleineMaus,
I am wondering which ROM u used on your orbit that includes tomtom?
Or do you just mean you still had tomtom stored on your menory card?
Cheers, Towelie.
Click to expand...
Click to collapse
hi, I've just used the last HTC offical Rom (see xda ftp site..) that include TomTOm + 1 city map
byebye
Hi, I used the ROM on the Wiki page Dopod|English|DOPOD001|ARTE1****|1.25.707.2 ??/??/0?|1.25.707.104|1.25.0000|02.69.90|4.1.13.30| [Download|ftp://xda:[email protected]/Artemis/Shipped_Complete_Updates/ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe]|[Thread|http://forum.xda-developers.com/showthread.php?t=286639]
It worked like a charm. The only problem I had was that when the Orbit re-booted after the process finished, it didn't seem to detect the sylus. I just waited five minutes and then it worked. Guess it was still getting settled in with it's new ROM. I don't know where I had the TomTom before I started the update, but it installed the German maps which were there before but as a bonus it gave me a English speaking voice which I didn't have before. It came with a German voice and I couldn't change because I had not yet upgraded the memory and had no room. So, my update was super! The only little thing is that once I changed the screen color back to blue instead of that terrible green, I couldn't get the phone part (dialing pad) to change to blue. No biggie, as now I can use my Orbit in English. I can live with the green phone pad! Maybe somebody will tweak that one. Hope this wasn't more info than you needed....
KleinMouse,
the dialing pad can be easily changed as well....just do a little seach on this Artemis forum and you will find many links pointing to skins available for WM5 phone edition.
O2 Orbit ROM upgrade info
Hi,
my o2 orbit has ROM 1.25.206.2 WWE. I wanted to know if this is the latest ROM available for my phone. I got my phone 10 days ago and i gotta do a soft reset on it every day. I had the same kind of problems with o2 Atom. But most of the issues were corrected once the ROM was upgraded. Please someone update me on my situation. Thanks
I tried the steps but i'm always getting the ERROR[300] : INVALID UPDATE TOOL - This Update Utility cannot be used for your PDA Phone. Please get newer Update Utility
Anyone who can help me here? I already tried different ROMs but always the same message
Did you unlock with imei-check? What is your model ID ARTExxxx ?
Yes i did. My Model ID is ARTE100
Hmm, but the steps described above are necessary to follow only if your model is Orbit (ARTE200). If you have HTC P3300 or Dopod p800W or Artemis or MDA compact 3, then you don't need to do it this way. The only thing you need to do is to unlock with Imei-check. If it still doesnt work, contact their help desk.
Ok i see, very strange indeed. I did the unlock with the stuff from Imei-check but i still get the message ERROR [244] : INVALID MODEL ID . If i try the steps from your post #1 , i get the described error obove. I'll try to contact the guys from imei-check, i hope they can help me
Hi Kleine Maus, I read with great joy that you succeeded and I would like to feel the same way.... Could you kindly reply to me and give me some detailed instructions to follow? Hopefully this will work for my HTC P3300....Thanks in advance.... I really appreciate it. Best SiperX
All you need:
http://www.geocities.com/gggbitonti
SORRY! fixing the link.. the site will be on line back WORKING! in 10 minutes!
thank you for segnalation
regards!
i followed the guide.
but when i turned the phone on for first time to load.
its loads slow and stays freezed...then i get an error
"Unknown SIM status.(Error 262144)
i think my radio rom maybe wrong.
if u know where to get a bin file..which i can upload via mtty1.42.exe
because i think my radio rom is old and i update to wm6 with old radio rom.
also it was a locked branded orange phone.
however before i proceeded with your tutorial i done the neseccary procedure such as regedit,,,super cid change and unlock sim
using spv services tools etc
so if you could help please i would much appreciate it..
because atm the phone is in operable and i would like to at least flash back to another rom or whateva....but it looks like i will have to do it through UI and mytt142.exe as these are the only things i can access via phone and pc.
thanks
...works fine with my sda music...only this horrible joysticbug
sandman: the .bin file for mTTY is on the last download link in the archive with WM6, here you can find mtty 1.42 to load the rom.. but to load the rom you need my SPL i share.. i don't know why it say you this sim problem rom.. the only tip i could give you is try to restart the procedure! my starting test was on a Typhoon WM5 updated.. but with the initial procedure you erase any old SPL... so, retry procedure step by step it work, i tested it 3 times before share and there are people who had success good luck!
...is there a way to solve this joystick-bug?
giuseppebitonti said:
All you need:
http://www.geocities.com/gggbitonti
Click to expand...
Click to collapse
could my make this work for htc monet
It work good at 565 but has some problems at 575 585,because the joystick and drivers are different.
weikey said:
It work good at 565 but has some problems at 575 585,because the joystick and drivers are different.
Click to expand...
Click to collapse
yessss t-mobile SDA (imate sp3i) rom update bad error joystic
keyboard dll problems wm6 rom not using
giuseppebitonti said:
All you need:
http://www.geocities.com/gggbitonti
Click to expand...
Click to collapse
Thank you so much I followed your instructions ang got a wm 6.0 typhoon ..its so cool dude...thxxx
but could be better I think if someone who know how to improve this wm 6.0 stuff...thxx
is there a way to application unlock in wm6
other than that it seems to work fine
works on imate sp3 now..
double blah
giuseppebitonti said:
All you need:
http://www.geocities.com/gggbitonti
Click to expand...
Click to collapse
Hi, thanks for the guide.
I am following the below steps in order to upgrade my untouched SPV C500.
Go to the folder where you extracted files from TyphoonNBFTools_0.3_SPL1010064_SPVServices.zip and run TyphoonNBFTools.exe
In menu select File > Open NBF... and load SPL1010064.nbf.
Right click on SPL1010064.nbf and select 'Emergency Flash' in popup menu.
Click to expand...
Click to collapse
Now, after loading SPL1010064.nbf, I am unable to proceed further. The reason is there is no SPL1010064.nbf visible there, so that I can right-click it... Could you please advise?
Never mind about previous post, I now got it to work. Looks fantastic so far, thanks a lot!
My mistake was I hadn't application unlocked the phone before.
This phone had been in a drawer for 2 years, and I believe it will again be in my hands, at least on week-ends.
Mega GREAT WORK !!!
It runs smooth on my dutch SPV C500
Who would have thought that WM6 on C500..
grtz!
didnt work for me. failed at first step with reliability test failed. Perhaps its cause i'm using vista.
I Have Application And Sim Unlocked My Phone But I Do Not Know If I Have To Do Something With The Cid Tool
FLORINOX, you have to SuperCID your phone
Hi to all...
I have flashed wm6 to my SPV C500 but my miniSD card is not working now...
???
EDIT:
I try other one and everything is ok....
well i made this a while ago, and finally got around to get it fully tested and release it.
this HardSPL is based on version 1.26 SPL. and is version 2 (2.00.cmon). also i *think* this one will not hard reset the phone
it's for any OPAL***** modelid now,
thanks to wlinsong and PhamQuang for testing
instructions:
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/...fd-ae52-4e35-b531-508d977d32a6&DisplayLang=en
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder (Opal_HardSPL_v2_0.zip).
2) you must have the phone synced with your PC, i.e. device must be in Windows Mobile!
3) run Opal_HardSPL_v2.exe.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) device should go to a grey screen
6) go on with RUU, Hard-SPL flashes, device automatically reboots, job done.
7 ) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 2.00.cmon
+1: if the screen won't go to grey mode (SSPL), then try manually entering SSPL by using the Opal-SSPL-Manual.zip - run the EXE on the phone then when it went to grey screen, run the HardSPL exe on PC and flash.
finally, donations are always appreciated to the "To Cmonex" link in my signature
now, enjoy the hardspl and cooked roms
UPDATE: How to flash stock SPL back for warranty purposes - please use this only if you need to return device for repair!
steps:
0. first flash entire stock ROM, then after that you can flash stock SPL as *last step*. do not reverse this flashing order please
1. get the RUU_Signed.NBH file from attachment (opalstockspl126.zip (185.3 KB))
2. run hardspl package from attachment (Opal_HardSPL_v2_0.zip)
3. *after* Opal HardSPL EXE extracts files, replace extracted RUU_Signed.NBH with the one from opalstockspl126.zip i.e. when asked to overwrite, say Yes, if it doesn't ask, then you are trying to copy it before running the HardSPL EXE, which is the wrong order.
4. flash just like you flashed HardSPL (see original instructions above)
5. device reboots, you can now check if it says 1.26.0000 or still 1.26.cmon or 2.02.cmon, in the latter case you did something wrong, it has to show 1.26.0000.
Great work, thanks for CMONEX !!!
I don't fully understand what this is for, but looks important soo THANKS
lupacche said:
I don't fully understand what this is for, but looks important soo THANKS
Click to expand...
Click to collapse
it's to allow you to flash any rom PhamQuang is already cooking some rom for opal i believe
OPAL10000 modelid
how do i check modelid?
FINALLY!!!!Congratulation !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
cmonex said:
well i made this a while ago, and finally got around to get it fully tested and release it.
this HardSPL is based on version 1.26 SPL.
it's for OPAL10000 modelid, if anyone has a different model, report in this thread... those should be tested out before doing anything.
thanks for wlinsong and PhamQuang for testing
instructions:
0a) make sure you have .NET framework installed on your PC! if not, get it from http://www.microsoft.com/downloads/...fd-ae52-4e35-b531-508d977d32a6&DisplayLang=en
0b) if you have vista, WMDC update is recommended: http://www.microsoft.com/windowsmobile/en-us/help/synchronize/device-center.mspx
1) download Hard-SPL package from attachment, extract to an empty folder.
2) you must have the phone synced with your PC, i.e. device must be in Windows Mobile!
3) run Opal_HardSPL_v1.exe.
4) follow steps in the RUU, and check on the device for prompts after PC shows loading bar.
5) device should go to a grey screen
6) go on with RUU, Hard-SPL flashes, device automatically reboots, job done.
7 ) to confirm you got it installed, go into bootloader mode (tricolour screen!) and verify the screen shows 1.26.cmon
+1: if the screen won't go to grey mode (SSPL), then try manually entering SSPL by using the Opal-SSPL-Manual.zip - run the EXE on the phone then when it went to grey screen, run the HardSPL exe on PC and flash.
finally, donations are always appreciated to the "To Cmonex" link in my signature
now, enjoy the hardspl and cooked roms
Click to expand...
Click to collapse
Thank for your hard working, but there's new issue occour.
When I tried to dump the hardspl, the error message appear"image file corrupted", then the work has been ceased.
If you have any idea about it, please kindly guide me!!
dpauser said:
Thank for your hard working, but there's new issue occour.
When I tried to dump the hardspl, the error message appear"image file corrupted", then the work has been ceased.
If you have any idea about it, please kindly guide me!!
Click to expand...
Click to collapse
Heihei~~ Just read the guide instruction carefully, I have fixed the problem.
And currently, I flashed a HK Rom code on my device.
However, I found a new issue. The this device has Compatibility with the BT ear price. I'm using a Itech D-Clip Radio one. When the call is coming, the call will be actived.But after the call, the BT connection will disconnect.
Any one has idea about this? Thanks a lot to all.
itaychi said:
how do i check modelid?
Click to expand...
Click to collapse
see bootloader screen (tricolour) it will say OPAL100 or similar... if the number is 100 then ok. if not, post in this thread
EDIT: oops, possibly for opal there is no modelid displayed there (could someone verify - i dont have an opal). use getdevinfo in mtty. but easiest is just try the spl package and if you get modelid error, post.
Hi cmonex, can you please make a HardSPL for the Touch 3G (Jade).
congratulations
hope to get fresh news on blackstone
thanks Cmonex
can it be used for htc T2223?
another question:
Can the rom upgrade file in the following link be burnt into my htc t2223?
http://www.htc.com/hk-en/SupportDownload.aspx?p_id=175&cat=2&dl_id=422
hi cmonex ! i've try ur hardspl , and i got a problem , my VIVA is hardspl now , but i try to use NBHTOOLS to dump the os.nb out of a WWE official rom and then use htc rom tools to rebuild a nbh file, but can not flash in to my viva . but i try flash that original official rom ,it works , is it my bad ? something i miss?
here is my htc rom tool setting:
[Opal]
ModelId=OPAL100**
SignMaxChunkSize=64
SPL=$200
SPLN=SPL
Splash1=$600
Splash1N=Splash
Radio=$301
RadioN=Radio
System=$400
SystemN=System
when i flash my edit rom , the ruu erro is "code 270 Updata erro the image is incorrect"
thanx alot for your hardwork
terry888_1978 said:
hi cmonex ! i've try ur hardspl , and i got a problem , my VIVA is hardspl now , but i try to use NBHTOOLS to dump the os.nb out of a WWE official rom and then use htc rom tools to rebuild a nbh file, but can not flash in to my viva . but i try flash that original official rom ,it works , is it my bad ? something i miss?
here is my htc rom tool setting:
[Opal]
ModelId=OPAL100**
SignMaxChunkSize=64
SPL=$200
SPLN=SPL
Splash1=$600
Splash1N=Splash
Radio=$301
RadioN=Radio
System=$400
SystemN=System
when i flash my edit rom , the ruu erro is "code 270 Updata erro the image is incorrect"
Click to expand...
Click to collapse
flash the radio as 0x300..
dr33 said:
can it be used for htc T2223?
another question:
Can the rom upgrade file in the following link be burnt into my htc t2223?
http://www.htc.com/hk-en/SupportDownload.aspx?p_id=175&cat=2&dl_id=422
Click to expand...
Click to collapse
if htc T2223 is htc viva, then yes
cmonex said:
flash the radio as 0x300..
Click to expand...
Click to collapse
but i've tried flash the os only , still not work ! u means i need to add the radio into it?
Stickied.
Ta
Dave
terry888_1978 said:
hi cmonex ! i've try ur hardspl , and i got a problem , my VIVA is hardspl now , but i try to use NBHTOOLS to dump the os.nb out of a WWE official rom and then use htc rom tools to rebuild a nbh file, but can not flash in to my viva . but i try flash that original official rom ,it works , is it my bad ? something i miss?
here is my htc rom tool setting:
[Opal]
ModelId=OPAL100**
SignMaxChunkSize=64
SPL=$200
SPLN=SPL
Splash1=$600
Splash1N=Splash
Radio=$301
RadioN=Radio
System=$400
SystemN=System
when i flash my edit rom , the ruu erro is "code 270 Updata erro the image is incorrect"
Click to expand...
Click to collapse
terry888_1978 said:
but i've tried flash the os only , still not work ! u means i need to add the radio into it?
Click to expand...
Click to collapse
terry ,
I've got the same problem as you.
vivi
terry888_1978 said:
hi cmonex ! i've try ur hardspl , and i got a problem , my VIVA is hardspl now , but i try to use NBHTOOLS to dump the os.nb out of a WWE official rom and then use htc rom tools to rebuild a nbh file, but can not flash in to my viva . but i try flash that original official rom ,it works , is it my bad ? something i miss?
here is my htc rom tool setting:
[Opal]
ModelId=OPAL100**
SignMaxChunkSize=64
SPL=$200
SPLN=SPL
Splash1=$600
Splash1N=Splash
Radio=$301
RadioN=Radio
System=$400
SystemN=System
when i flash my edit rom , the ruu erro is "code 270 Updata erro the image is incorrect"
Click to expand...
Click to collapse
%1 Get a error270,image file corrupted!!!
htcrt.ini
[Opal]
ModelId=OPAL100**
SignMaxChunkSize=1024
SPL=$200
SPLN=SPL
Splash1=$600
Splash1N=Splash
Radio=$300
RadioN=Radio
System=$400
SystemN=System
Hi everyone, I just recieved my brand new Diamond2 in Czech localisation (original from retailer) and after first boot I got this error:
Error
Install
\Windows\OpenCZ_Settings_Topaz.CAB
failed, code=0x80090006
I assume its the czech localisation but any advice? If I dont solve the problem, Ill send it on monday back
Regards
Pylorus
There are a couple of things you can do:
- Manually try to install it using the file explorer: \Windows\OpenCZ_Settings_Topac.CAB
- Make a hard-reset (hold Vol-up & Vol-Down and press the reset button under the battery case to see if it happens again.
Thx for swift reply ...
- I tried several hard resets and booting with / without SIM and or microSD - still the same error
- I managed to get the phone partially working, because you can move the error window aside and access the startmenu and open explorer. I executed the file manually, but got the error message: "The program cannot be installed because it is not digitally signed with a trusted certificate."
Unfortunately I can not access the phone via USB (first customisation hasnt finished and active sync does not open) and I'm afraid flashing the device with another ROM because of warranty
Any Idea how to tweak the phone to lower the phones security allowing installing not signed cabs?
Thx...
well if you get this error even after a hardreset, you should definitely send it back..
OliveJeans said:
well if you get this error even after a hardreset, you should definitely send it back..
Click to expand...
Click to collapse
I will ... but any idea how to lower phones security?
pylorus said:
Hi everyone, I just recieved my brand new Diamond2 in Czech localisation (original from retailer) and after first boot I got this error:
Error
Install
\Windows\OpenCZ_Settings_Topaz.CAB
failed, code=0x80090006
I assume its the czech localisation but any advice? If I dont solve the problem, Ill send it on monday back
Regards
Pylorus
Click to expand...
Click to collapse
My device from Czech too. I found this cab file in Windows folder, if you need it i'll upload it for you.
pylorus said:
Thx for swift reply ...
I executed the file manually, but got the error message: "The program cannot be installed because it is not digitally signed with a trusted certificate."
Any Idea how to tweak the phone to lower the phones security allowing installing not signed cabs?
Thx...
Click to expand...
Click to collapse
Try sdkcert. That should do what you want install it before installing your .cab what is needed
Problem solved - i sent the device back and the whole board was replaced - new IMEI, but now its working like a charm
for the future..I have had a same problem with my TD2..After few hours I found out that I could this error off in taskmanager. Then it worked.. It was just some czech layout for my topaz but I did not want it either.. So for those who will buy TD2 with this error and don´t want chzech langugage on it, just close it in taskmanager..