Related
Hi... something happended with my Vario II or PC. Now when I connect my Vario II to the USB port, ActiveSync cant find it ('Not Connected') and Windows says: 'USB Device not Recognized'. I reinstalled all software that came with the Vario II, but its now working... Anyone help me, please!!!
Hi Jannen,
I've seen this before - but it usually cures itself after a PC and phone reboot (I would guess you have done this already. The issue appears to be either Windows USB host, your phone or the cable/connections on your USB cable.
I would suggest you try the following and see what happens...
1. On the TyTN goto Start > Settings > Connections > USB to PC - change the setting here from what it currently is.
2. Try a different USB cable if you have one.
3. Try a different USB port on the PC. Possibly on a different USB host if you can do that.
4. On Windows goto Control Panel > System > Hardware > Device Manager - look at the error appearing in the Universal Serial Bus Controllers. This might help identify the problem. Also try re-installing the drivers from here.
5. On the TyTN goto Start > Programs > Accessories > Wireless Modem - ensure this is not active. I think it automatically stops when you exit Wireless Modem but it does change the USB behaviour.
6. Install the latest ActiveSync program on your PC. I'm currently using 4.1 and 4.5 BETA and both are Ok. http://www.microsoft.com/windowsmobile/activesync/default.mspx
Post the response you see to each of the above and it will help diagnose and hopefully fix your issue.
Gav.
Works finally!
Thanks for your help! But took a while to sort it! I tried all those steps, again and again, with no result. I even updated the Active Sync etc. But after a soft boot of my Vario II - its finally working! No idea where the problem was though, one of those Windows mysteries is my guess.... :/
Thanks again!!!
Prior to upgrading to ARHD 3.2.1, I could plug my Transformer into my PC and see it each time. However, after I flashed ARHD, it no longer shows up in My Computer. It does show up in Device Manager as Android ADB Interface. Any ideas out there? I have installed SDK Manager and installed ASUS Synch still not showing up.
Try going into settings -> storage -> the 3 dots in upper-right corner -> usb computer connection -> check media device(MTP).
If its checked already, check Camera(PTP), then recheck MTP.
If that doesnt help, try reinstalling the drivers.
Goatshocker said:
Try going into settings -> storage -> the 3 dots in upper-right corner -> usb computer connection -> check media device(MTP).
If its checked already, check Camera(PTP), then recheck MTP.
If that doesnt help, try reinstalling the drivers.
Click to expand...
Click to collapse
Goatshocker....a million thanks my friend. that did it.
I have my sg4 plugged into my laptop, but it is not showing up in the android debug monitor. I ran it as administrator, and the device does show up in my computer.
Do you have debugging enabled in Developer options? Make sure you have the right drivers installed otherwise you may need a reboot on both devices
I have the Nexus 7 drivers installed, and the adb interface.
and I do have debugging enabled.
I think that you need the Samsung drivers. The Nexus 7 drivers are different ones. So download them here: http://www.samsung.com/us/support/downloads
They should also be installed if you install Kies.
sniper8752 said:
I have my sg4 plugged into my laptop, but it is not showing up in the android debug monitor. I ran it as administrator, and the device does show up in my computer.
Click to expand...
Click to collapse
There is a well-hidden menu that you may need to access.
Assuming you have developer mode enabled...
- Go to Settings, then Storage
- Click on the menu (top right)
- Select USB computer connection
You'll see 2 boxes:
- Tick 'media device'
I found that if neither box was ticked, I couldn't see my device...
Maybe the first time the dialog says "Allow this computer debugging" appears, you clicked NO.
Try go to Developer options and click "Revoke USB debugging authorizations", and reconnect the device.
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
U saved me BRO!!..was tired of using OTH
U saved me BRO!!..was tired of using OTH
Applying all things you said but yureka not connect with computer
USB Computer Connection is still not popping
Hi, I have tried all that is said above, but still I am unable to connect my Yureka to PC. USB Computer Connection is still not popping any options.. Please help
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
well i have tried that but it wont even detect my yureka. IT DOESNT EvEN SHOW A UN RECOGNIZED DEVICE. HOW TO RESOLVe
?
Problem Solved
1. Proceed as Above.
2. Reboot your Phone.
3. Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
Problem Solved...
The problem is not in the phone, or can't be solved by it
Actually you have to do this via pc.
1)search update drivers and find the update device drivers option
2)in other devices find Android and double click
3)click the driver tab
4)click update driver
Worked for me ?????
PC connection Still its not working
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
Hi..
After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected"
can any one please help me ?
---------- Post added at 08:05 AM ---------- Previous post was at 07:59 AM ----------
Sahil Badal said:
1. Proceed as Above.
2. Reboot your Phone.
3. Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
Problem Solved...
Click to expand...
Click to collapse
After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected"
Yureka not connect to PC
[[/B][/B]
RAUSHAN0704 said:
Since many guys are not able to connect their yureka phone to PC so for them this thread might be helpful. I was also facing the same problem, even USB computer connection setting was not popping up. So following are the steps to resolve that problem.
1. Go to Settings -> About Phone -> Tap several times on Build Number to enable developer Options if you haven't enabled it yet.
2. Now You can see one setting titled "{ } Developer options" under Settings Menu. Tap on developer options and enable "Android Debugging".
3. Now connect your phone to PC via USB cable. Now You will see that your phone is successfully connected for debugging. Now without disconnection your phone from PC, go to settings->Storage->Menu (Three vertical Dots at top right corner of the screen). Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox.
4. Now you are ready to access your internal and external sd cards of your phone. Enjoy
Click to expand...
Click to collapse
I have followed all above steps, but not shows USB connection.
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", this problem is after getting my replacement handset.
Hi, I have tried all that is said a, but still I am unable to connect my Yureka to PC. USB Computer Connection is still not popping any options.. Please help vikas meena 9694746144
Dear Sir,
As per your instruction i go to the setting but as u written
"Now click on "USB computer connection", now the usb setting pop up will come. Now enable Media Device (MTP) checkbox. "
after tapping computer connection nothing pop up arises. I can not enable Media Device (MTP)
Please guide me.
Suresh
vertexpac said:
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", this problem is after getting my replacement handset.
Click to expand...
Click to collapse
did u get any solution bro????..... i cant copy files to pc and root
---------- Post added at 05:33 AM ---------- Previous post was at 05:30 AM ----------
shadowkill97 said:
well i have tried that but it wont even detect my yureka. IT DOESNT EvEN SHOW A UN RECOGNIZED DEVICE. HOW TO RESOLVe
?
Click to expand...
Click to collapse
did u got any solution bro... i cant connect my yureka to pc. i want to root it. But i cant connect it
USB connection problem
I am also getting the same problem "After pressing "USB computer connection" USB setting Popup is not coming. and it says "USB is now Disconnected" ", plz help me
yureka AO 5510
Sir,
My yureka AO 5510 hardbricked and i used emmc image and enter into fastboot mode ( by only pressing power button it can switch on and work) but to flash this is not shown in device manager. I tried with usb driver, adb driver, nothing happend.... and gave to shop and changed its usb port.... but no use....
i can power on it with this memory card or go to fastboot mode.... can not connect to PC.... Please help me....
thank you for your practical guidance, because since so many days and several times I tried to connect with my laptop, last i thought to install some yu drives in my laptop, but this is a very useful points, you are putforth in this moment. once again thank you for the substantial helping tendency you have shown. may proceed it in future to help others,
i am using yu yereka lolipop os and windows 10 x64 pro and tried all method to install drivers but even when i connect my yu yureka ao5510 then it shows me (device disciptor request fail)error code 43.i did all thing from disable driver enforcement and various adb drivers but not success yet..
and when normally connet phone to pc it also not showing the adb option and mtp driver.i aslo tried with different pc but same problem....
plz guy help me!!!!
Got ot developer tools and enable the android debugging.. reboot the mobile
After reboot a pop up window will be opening and asks for disable the android debugging .. disable it in developer tools and then connect the usb cable again . then the pop up will be coming as usual ...and problem got solved
Yureka not connect to any pc
Pc shows popup that the device is malfunctioned.
In device manager it says device dicriptor request failed.
vrishabhv2 said:
i am using yu yereka lolipop os and windows 10 x64 pro and tried all method to install drivers but even when i connect my yu yureka ao5510 then it shows me (device disciptor request fail)error code 43.i did all thing from disable driver enforcement and various adb drivers but not success yet..
and when normally connet phone to pc it also not showing the adb option and mtp driver.i aslo tried with different pc but same problem....
plz guy help me!!!!
Click to expand...
Click to collapse
did you find any solution?
Hi, just a slight problem. I happen to select charge only for the USB connection and now I can't unselect it to transfer files. I checked online and see in storage in the overflow menu when I select it USB computer connection comes up put when I press it I just get a message "USB is now disconnected". Nothing else. How do I reselect MTP again?
Thanks,
cactrx said:
Hi, just a slight problem. I happen to select charge only for the USB connection and now I can't unselect it to transfer files. I checked online and see in storage in the overflow menu when I select it USB computer connection comes up put when I press it I just get a message "USB is now disconnected". Nothing else. How do I reselect MTP again?
Thanks,
Click to expand...
Click to collapse
Just go to Settings than select Developer Options, scroll down to find Select USB Configuration. It's a long page, so scroll down slowly and carefully.
sanctitude888 said:
Just go to Settings than select Developer Options, scroll down to find Select USB Configuration. It's a long page, so scroll down slowly and carefully.
Click to expand...
Click to collapse
No, I don't have that option under the Developer Option.
cactrx said:
No, I don't have that option under the Developer Option.
Click to expand...
Click to collapse
Anyway my ZE551ML is on Android M.
Follow this link for screenshot : https://photos.smugmug.com/photos/i-xhLrFLf/0/M/i-xhLrFLf-M.jpg
sanctitude888 said:
Anyway my ZE551ML is on Android M.
Follow this link for screenshot : https://photos.smugmug.com/photos/i-xhLrFLf/0/M/i-xhLrFLf-M.jpg
Click to expand...
Click to collapse
Sent from my ASUS_Z00AD using Tapatalk
kenbo111 said:
Sent from my ASUS_Z00AD using Tapatalk
Click to expand...
Click to collapse
My developer options doesn't have this setting. I'm not sure how to do a screen shot but under that section is:
On
Development tools
Take bug report
Advanced reboot
Desktop backup password
Stay awake
HDCP checking
Enable Bluetooth HCI snoop log
Process stat
Root access
Updaye Cyanogen recovery.
Then it goes into Debugging.
Should I be looking somewhere else?
Thanks,
I have found that I can't enable Android Debugging which has the switch greyed out.
I see it says in the subheading "Device is in charging mode, USB debugging is disabled".
Maybe if I can enable the debugging somehow I can get the phone out of charge only mode.
Any ideas?
Thanks,
I have found its not actually greyed out. Just not responding to tapping.
Hi see this problem has been mentioned here:
http://android.stackexchange.com/qu...sb-debugging-after-upgrading-to-android-5-1-1.
'm trying to find "persist.sys.usb.config" to delete it as a fix but haven't found it yet.
Already tried that. Selecting 'USB Computer Connection' displaying message 'USB is now disconnected' (even when it's not connected to a cable)
cactrx said:
Hi see this problem has been mentioned here:
http://android.stackexchange.com/qu...sb-debugging-after-upgrading-to-android-5-1-1.
'm trying to find "persist.sys.usb.config" to delete it as a fix but haven't found it yet.
Already tried that. Selecting 'USB Computer Connection' displaying message 'USB is now disconnected' (even when it's not connected to a cable)
Click to expand...
Click to collapse
Seems like you are using custom ROM, I'm on stock, nothing much I can do to help. Is the driver correctly installed? How did the Windows response to USB connection with USB debugging off? With the USB debugging on, it will ask for authorization when connected. I believe "persist.sys.usb.config" is part of build.prop, so it's kinda risky to play with, but if you manage to find that line (you may simply add # in front of it, just to be safe and in case you need it in the future).
Hi, thanks for your reply.
Windows shows nothing when I plug the phone in. It use to come up with the phone and SD card fine.
I'ts just that I can't turn debugging on. I'll have a look in build.prop and try the #
Thanks,
Any ideas where I put the #? I have attached the build.prop file.
Thanks,