Related
Just tried to upgrade my S200 with a 9100 ROM ver 2.8.7.1 WWE (by mistake of course) and I can't turn it on anymore. Somehow it didn't even warn about wrong ROM.
Tried to hardreset it but no luck. When I keep the camera button it goes to RGB only when connected to the charger.
When connected to PC, the red and blue leds keep flashing and my PC gives Error 260 when I try to revert back to the S200 RUU.
Does anyone know how to bring it back to life? Is there a way to boot it from SD card?
-
I-mate Jam
Qtek 9100
Qtek S200
Don't panic!
I did the same thing some time ago!
What you need to do is make sure that the battery is fully charged. (The flashing of the screen can be a result of the flat battery.) Unfortunately, it is not possible to charge the battery when the wrong ROM is installed, as the ROM obviously tells the Prophet how to charge.
Let's assume you have an okay battery.
1) Start the Prophet in Boot mode. This is done by pressing and holding the Camera button and then pressing the soft-reset button. Keep holding for about 7 seconds, and the coloured bands should appear.
2) Connect to PC using the UDB cable.
3) Run the correct ROM upgrade. You do not need to be paired with ActiveSync, as the update programs are intelligent.
4) If the update does not work (and it fails at 95%), then try again. If it still fails, try again and do a soft-reset mid-way through. This will kill the ROM upgrade and you should then be able to do it fine after that.
The really important thing is that the battery is charged before you do this. Unless anyone makes a USB cable that can charge AND connect to PC, then a fully charged battery is a must.
Let me know if this helped.
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Check this Out
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Re: Boot from SD?
zealerc said:
one more step need to be performed which by not ticking off the ALLOW USB CONNECTIONS in the connection settings of the file of the activesync. After configuring it, it would absolutely carry out thy upgrading of ROM for thy Prophet which is in Bootloader mode. Good Luck!
Click to expand...
Click to collapse
I am a bit confused, does that mean that ALLOW USB CONNECTIONS has to be chacked or unchecked?
I did the same exact mistake. Now, my baterry is fully chaged (which I can check on another phone) but when I put it in S200 it shows that the battery has 0%. Conseqeuntly, when i unplug the power cord the phone dies. I have no way of running the new ROM on it. I tried running a bootable SD but it only installed part of the software. i read on this forum that such a thing happens and that one would need to run a full version ROM from a computer. So, how do I do it??? I am almost giving up all hope of ever making this phone work
Does anyone have a file to boot from SD and is it possible to run a full ROM from SD. Please help!
Hello Everyone
I need big time help. I just bought Hp 6945 and I tried to update GSM rom from 1.02 to 1.08, while updating it says update fail and try to restart Ipaq and start again. Now My problem is Ipaq just stuck to Hp invent logo. I tried to reset and hard reset and remove battery but notthing work.
I need help
Could some please help me to How to fix this problem?
Thank you
same BS happened to me. the only way to fix it is to load the UK 6915 ROM. thats the ONLY way to fix it. AVOID this update do not try to update the radio. I bricked my phone doing this. STILL looking for a solution. Radio stack is daamged.
where Can I find Uk 6915 rom
Thank you for reply. Where can I found the UK 6915 rom. Is there any instruction to How to load rom?
Thank you
If is FIXEDDDDDDDDDD
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
No network connection
Ok everything work fine, but Now I cann't connect to tmobile. It keep showing me no service.
Any Help please
Ok It is fixed again
There is another update at HP website, which is software update. After installing that everything working fine.
can anyone help? i just bricked my ipaq 6965 too. had already followed those few instructions without any success.. what do you mean by "with or without SIM card"?
After a soft reset, mine's stuck at the initial blue/white boot screen.
Hard reset doesn't work (assuming its call + hang up + power + poke reset).
Ideas?
bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845/Ipaq_HW69XX_ENG_ROM.zip.html
download files from rapidshare posted by me ,r tested on my phone
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
garyakw said:
hi i have tried to dl the rom asi having the same prob but the file cannot be downloaded. is there any other way to get from you
Click to expand...
Click to collapse
If you are stuck on a HP Invent Screen, with G.39, etc.
And you have tried to hard reset and softreset with no luck, this is what you do.
XP Instructions:
1. Download this link http://www.mediafire.com/?3ygfbx0sjdy
2. In the taskbar area in the right hand corner, right click on activesync, bare with me, I'm using Vista and have to remember this, click connections..., you need to uncheck everything click ok or apply...
3. press ctrl-alt-delete, end process wscescomm.exe, (named something like that, end the process.
4. Extract the file you downloaded if needed.
5. Connect your device to the usb port on your computer.
6. Run Uni Exit Bootloader Application. Done
Vista Instructions:
1. Download these 2 links, and extract them if necessary.
http://www.mediafire.com/?3ygfbx0sjdy
http://www.mediafire.com/?9pmjkponfsg
2. Start Device Manager, (Start-Control Panel, Class View[Far Left Corner])
3. Connect HW6900 to USB port, you should now see a Mobile Devices (Next to + sign), Double Click
4. Right-Click on the Device, Click Update Driver Software, Choose let me pick from a list, Uncheck compatible hardware box.
5. Click have disk, Browse to location where USBAS is extracted, choose the wceusbsh.inf file, Double Click.
6. You should see Microsoft USB Sync, if not and it reverts back to the already installed file, and the box rechecks itself, uncheck it, choose microsoft, and choose the latest Microsoft USB Sync to install
GOOD LUCK
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
i get error 402.... times out and no can do.... what was that about german language... maybe i just need it spelled out. which screen does the unit need to be in. there is two... monochrome serial vs usb and there is the hp logo blue and white screen frozen indefinitely... please help i love this phone...
Hi, the rapidshare file is missing!
Could you give working link or send me the file to mail, please?
ipaq dude said:
Ok
I got it fixed, very simple solution
found it here
http://pdaphonehome.com/forums/hp-h...dowloaded-rom-update-ipaq-dead-need-help.html
Solution:
this is what I did to get this fixed.
1) Get the battery out of the iPaq, and wait for a few minutes while the "serial" image fades away slowly.
2) In the meantime, prepare your cradle, plugged into the AC charger and plugged via USB to your PC.
3) After a few minutes, with the screen of the iPaq completely gray, put the battery and battery cap back on (with our without SIM card), and put it on the cradle immediately.
4) The iPaq should start coming back to life, as if it were being hard reset. Let is stay on the welcome screen (i.e., do not tap it or anything).
5) Restart the upgrade process, it should proceed from there OK
Thank you to origianl solution provider
Click to expand...
Click to collapse
Man,r u sure the above can work well???? Confusing......I did the above like u indicated,but it's not work on my device HP6915,could u make it in details how u fixed the problem of updating ur device,thanks!
Regards,
Brose
Thanks, This help get me out of freeze
Thanks for posting this link. It brought my hw 6945 back out of the freeze. Stay away from HP's site update. Bad news
johnnynomadic said:
in reference to
Default bring back to life hw6945
i'we tried like you to upgrade radio part and a got an freezed phone
Solution for repair was flashing firmware with this program..
Download-Link #1: http://rapidshare.com/files/96527845...G_ROM.zip.html
its a no go here...
Click to expand...
Click to collapse
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Maybe
Most Likely Yes
bmw2320 said:
Thanks for UNIEXITBOOTLOADER thing, it makes my 6965 rocks again! Btw, could this file be used on other pdaphone such as O2 Atom? Thx b4.
Click to expand...
Click to collapse
cdguider said:
Most Likely Yes
Click to expand...
Click to collapse
I don't think so,Curtis.....But as I know most of dopod device hardly be dead....
Hi: This is my first posting and I am new on this board. I have had an MDA that I got as a gift from my Dad and I love it. However, I used it last week and for some unkown reason, it is stuck in the:
'Press Send to Restore Factory Defaults, Other Key to Quit.'
I have been trying to get past this for 4 days and am not having any luck.
I got to the Align Screen and that happened only once. Then I could not get past that. It keep showing the Align Screen and I kept tapping and it just kept going round and round from the Center Tap to the sides and back.
My battery is fully charged, I have read this forum and still I am lost. I would really appreciate any help. Thank you so much.
Toni
Do a Soft Reset or Hard Reset.
Cheers!
zabardast_1 said:
Do a Soft Reset or Hard Reset. Cheers!
Click to expand...
Click to collapse
Thank you for trying to help me. However, I have done both of the resets over and over and I keep getting the same result. 'Press send to restore factory defaults, other key to quit.'
I can get no further than that display regardless of what key or keys that I hit.
I have even tried the two ways of doing a Hard Reset:
1. Hold Com and Voice while pressing Soft Reset Button for 5 or more seconds until I get that display.
2. Hold Com, Voice and Camera while pressing Soft Reset Button for 5 or more seconds until I get that display.
I cannot get past that display regardless of what key or keys I press.
It seems frozen at that display point.
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Tonis said:
Tried again this am to hard reset my MDA. Now it goes and shows the T-Mobile screen with the IPL/SPL etc. Then goes into Windows and to the Align Screen and for some reason will not recognize the Screen Tapping to align the screen.
I did try to use my PC to recognize the MDA, but it would not. Downloaded WST and that would not recognize my MDA either. I understand that until I get past the Hard Rest my MDA will not be recognized by my PC due to ActiveSync being requried to connect my MDA to the PC. I don't know what else I can try. Search all day yesterday and could not find any solutions. Will continue today. Any suggestions, Please. Thank you.
Click to expand...
Click to collapse
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
sleurhut said:
Use the love rom to set phone back to "zero". Therefore you must press press the voice and camera buttons if joy reset youre phone.
You get some collored bloks om youre phone and then you can use the love rom.
After that you can use youre original rom updater
Click to expand...
Click to collapse
Did a search for Love Rom and Wizard_Love ROM and only came up with 103 results consisting of some Threads with 1570, 898, 618,787, 893, 464........postings on the first page for Threads 1-25.
Now I do have a Red, Green, Blue, White Screen with RUU in the top right corner of the Red Bar with IPL 2.26 and SPL 2.26 in the Red Bar. Nothing is in the Green, Blue or White bar.
I tried to Hard Reset and Soft Rest and nothing happens. I removed my Battery and then tried again and still nothing happens?
Where can I find Wizard_Love ROM and what do I do when I find it. My PC will not recognize my MDA and I used WST and that cannot located my MDA.
I am at a complete loss of what to do next.
Thank you in advance for taking the time to try to help me get my phone operational.
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
Thank you again for your help. Prior to this posting I found:
epimazzo Posting at: http://forum.xda-developers.com/showthread.php?t=294107&highlight=bootloader #1 and this is what cleared up my problem and now my MDA is running GREAT!!!!!!!!
This was the same thing that you posted for me, too.
Maybe some of you are already aware of this procedure, maybe not.
Anyway, it worked for me and I decided to share how to do it. Simple.
This procedure should only be used in case you really need enter into a bootloader mode (Red, Green, Blue, White Screen) and all other ways to do it has failed! Hold Camera button is one of these I am mentioning.
1. Make sure your Phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your Phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Don’t use the IrDA or Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
So, Thank you all for your time and help. I do hope this helps others to find a way to correct their problems.
Thanks !
Yes.thats exactly what I wanted you to do
I'm glad you got it up and running fine
Cheers!
zabardast_1 said:
sleurhut
Use the love rom to set phone back to "zero".
do not confuse guys with this statement.Wizard_love_Rom is a patched rom which is flashed to recover back the phone in some stuck up phones,but it doesn't set the phone back to 'ZERO',but its an italian language rom.
Tonis
The multicolor screen is the bootloaders with IPL/SPL 2.26 displayed,this is the mode from where you can flash another rom.There's no need to get the phone activesync,cuz it won't activesync in bootloaders.But when in bootloaders,connect the phone with pc via usb cable and watch small usb appear at the bottom of the bootloaders,if its there then you are good to go and can flash a rom.
Now,download the official T-mobile 2.26 from the link below and get the phone in bootloaders,check usb appear at the bottom and flash it to recover back to the default status of the phone.
http://forum.xda-developers.com/showthread.php?t=342744
Cheers!
Click to expand...
Click to collapse
I does everything you do but
I don't have the cradle :S
so that means a problem?
or there a nother way?
Hi!
I got an mada vario 4. How can I upgrade the rom on it? Or can I change the t-mobile touch flo to manila 2.5? Thx! Zoli
Hi all.
I just a got a HD2 today. And the first thing that came in my mind was "Let's go to xdaDev to get a nice custom rom". I downloaded one.
After that I put the usb and try to make it syncronize. And the problem is here : ActiveSync dont reconize the phone. I spent the last 4 hours to google why it shall not work. I tried to unstick option at "Start=>Settings=> Usb to PC" but it dont work. Nothing more after perfoming a hard reset and reinstall ActivSync.
But something is strange : When I go in the bootloader, there is the 3 color screen and the phone Display "Serial" at the bottom of the screen ; and when I start it again with USB plugged, it doesnt display "USB" instead of "Serial" it's just void and if I remove the USB "Serial" is displayed.
Plz help me to make the phone syncronize .
I use Windows XP (no firewall, no antivirus) and an official Orange Rom. My SPL is 1.42.0000. I just hope there is no hardware problem ...
Some news ...
The HD2 isnt detected on 2 other PC (Both Win XP). I managed to syncronize my old Diamond too, and it worked well. Same with a HTC Touch and a Touch Cruise, the 3 ones works.
I also tried to use Bluetooth to get an Activesync connection and this time, it noticed the HD2 but no way to get a synchronization.
Any ideas ?
Try this: goto Settings, Other (Miscellaneous settings), USB to PC, Enable faster data data synchronization. Try to tick and untick the last setting.
It doesnt work . I'm trying to follow a "GoldCard" tutorial to flash to an official HTC rom. Maybe it's Orange operator rom ... But if you have any other suggestion, let me know
I can't believe that it's such a s*** to just connect the last HTC phone to a computer. The tutorial need ActiveSync to get the SD card ID so I will not succes in this way.
Is there another software that can be used instead of ActiveSync ?
Did you flash any rom at all or are you still stock?
If you have flashed already, Have you tried to go back to the default shipped rom using sd card (not goldcard)?
Find the rom that shipped with your device, extract the RUU_Signed.nbh file from it, copy it to your fat32 formatted sd card, rename leoimg.nbh, put card in phone, boot phone with down volume held, hopefully you get the message on the three colour screen saying something like 'press volume up to start' or somesuch.
THis should not only flash the rom, but also fix spl if it has become corruptted(which appart from hardware errors is the only reason i can see that it wouldn't recognise a USB connection)
Make sure it is the correct rom for your phone, though, correct vendor and region id.
I must say if you havent flashed yet it sounds like a hardware fault with teh usb cable/connector
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Phoque_You said:
I'm currently running a stock Rom from a french operator nammed "Orange". I haven't flashed anything since ActiveSync just dont want to know anything about my HD2.
Maybe I shall send it back to the seller. That's so frustating ...
If i dont find a way to solve this problem until the end of the day, I will return the phone.
Anyway thx for trying to help me
Click to expand...
Click to collapse
Ah in that case then i'd seriously consider taking it back /sending it back. Especially if you have tried more than one computer, sounds to me like faulty cable or USB socket.
kilrah said:
To me either the cable or the phone is faulty. Try another cable if you have one, if not just have the phone exchanged.
Click to expand...
Click to collapse
You must be right. I tried everything and I never had so much pain with my others HTC to get syncronization
I had the same problem not beeing able to connect to the internet via computer. After playing with the activesync settings on the Computer -> conection settings-> ticking on and off some of the boxes->ok, it worked again.
I have connected to three of these phones ( 2 french 1 english) and no problem whatsoever, everything happens without needing to touch any of the settings...is your pc even recognising that something is being plugged in on the USB?
Have you installed the latest version of activesync?
If you have done all the obvious things and it still does not work, the phone or the cable is defective...It should connect straight out of the box with a standard, un changed version of activesync.
Send it back!
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
nzane said:
Hello,
I have a problem, when I connect my phone with the USB cable to my computer, it doesn't do anything. He don't recognize the phone, doesn't make any connection nor see the SD card.
I've already tried to clear the box: Enable faster data synchronization, and tried to choose Disk Drive (Faster file transfer), it all doesn't do anything.
Tried different PC's, with WMC and Active Sync 4.5, with different OS's.
The cable isn't broker or something because the only thing that happens when I connect the phone with my PC is that the orange light (battery charge) is on.
I've installed Shadowline ROM, but it did work with that rom (active sync and disk transfer).
I think it is a problem of the ROM tho, so is there any way to flash my ROM without using a PC?
Answers would be realy appreciated.
Thank you.
Click to expand...
Click to collapse
You can flash from the storage card, just rename the .nbh file to TOPAIMG.nbh and put on the root of your storage card, go to bootloader mode and it will flash.
Your cable can be bad and still charge. I would try a different cable.
Also try deleteing the partnership in Active Sync and try to reestablish it.
I assume you hard reset after you flashed the ROM.
I do not think its a ROM issue.
Ok thanks for your reply.
I did what you sad but when I loaded the TOPAIMG.nbh in the bootloader, it came up with an error and freezes on: Loading ...
When I restarted it It Only shows:
___________________________
RUUNBH
TOPA100 32M
SPL-1.83.000
MicroP-Topaz (LED) v10
TURBO HW/TURBO SW
TP MFG DATA
510,547 180,883
177,209 842,207
844,844 Calibrated
Upgrade ROM code Error
Please try again
_______________________________
And then he goes to the white screen with the blue letters saying: Loading...
(I waited many times, one time for 2 hours but nothing happend).
When I put out my SD-card and the battery and connect the phone with the USB (my pc still don't see recognize anything) it will boot to the exact same screen as I typed here above but then he stays at that one.
I can't do anything, already tried to hard reset him but that also didn't work.
It feels like im pretty screwed..
Please help!
Maybe you have a problem with the mini USB.
Happen to me with Touch HD.
If so take it to a reppair shop.
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
nzane said:
Well, I borrowed and USB cable from my friend and now he indeed makes an connection. But no active sync connection. I also can't see my SD card in My Computer. He still only shows the screen that I typed here above, but then under in the white area a little text: USB
What do I have to do next to fix it,
please help
thanks
Click to expand...
Click to collapse
I am concerned that you screen shot shows SPL 1.83.00, but you have flashed Shadowline's ROM.
It should say SPL: 1.83.00Olinex which would mean you have HSPL installed which is absolutely required to flash a custom ROM.
Did you have that ROM operational and just couldn't sync, or has the device not worked since you flashed this ROM?
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
nzane said:
Yes, I had the shadowline ROM, and it al worked good. I also could connect my mobile to my pc with the USB cable.
I don't know what happend, I didn't install any other program or something else but I suddently couldn't connect my mobile phone to my pc anymore.
But I wanted another ROM because I noticed that the Shadowline ROM feld a little bit laggy, so I found out that you can do that by your booting with the SD card.
And I know that you have to install hardSPL first, so I downloaded that one from the big post in this ROM forum from Topaz.
Booted with the SD card, and then when I started to flash the ROM he gave an error and now I have to problem that I can't do anything anymore.
Click to expand...
Click to collapse
I guess my point was if you had Shadowlines ROM, you were already HSPL'd, no need to do again.
Hard reset the phone and try to install ROM from SD.
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
nzane said:
Well, If I'm hard resetting, the only thing he does is show the percentages, then he says completed, then he reboot en I'm back at the tri-color screen again.
And I can't enter the bootloader, so I also can't install the ROM from the Sd-card.
And taking out the memory card while the phone is on also dont work
Any other options what maby will work?
Click to expand...
Click to collapse
Just some points;
Make sure the .nbh file is named excatly TOPAIMG.nbh paying attention to the case of the letters.
When you attempt to go into Bootloader, Holding Voume Down and Power buttons at the same time when phone is off, what screen appears?
[Q] my handset doesn´t recognize sd apps
I had the same problem as well, so I deactivated and reactivated the SD card from the phone, actually I cant take out the sd with the turned on phone. It worked once, but it happened again so i tried to the same but know the deactivate function in settings doesnt worked. Now i dont know what to do. if anyone could help me i would be very thankful.
My handset is a xperia x10 with 2.1 generic flashed bb 2.1.54, and 2.2 wolbreak gingerbread rom.
eiffeltom said:
Hi,
i had once the same problem. No connection with PC anywhere. I couldnt do nothing with that and was quite desperate about that.
But once suddenly it came to work again. I am not sure what made it work again but the only thing I can guess was that I took out and gave back the memory card with the turned on phone. Since then I have never had this problem again.
I wish you that this taking out of memory card helped you too.
Click to expand...
Click to collapse